Numerical Investigation of the Effect of Purge Flow on Aerodynamic Performance and Film Cooling Effectiveness on a Rotating Turbine With Non-Axisymmetric Endwall Contouring

2012 ◽  
Author(s):  
M. T. Schobeiri ◽  
K. Lu ◽  
J. C. Han
Keyword(s):  
Numerical Investigation ◽  
Mass Flow ◽  
Flow Injection ◽  
Film Cooling ◽  
Preceding Paper ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Purge Flow ◽  
Endwall Contouring ◽  
The Impact

The impact of the purge flow injection on aerodynamics and film cooling effectiveness of a high pressure turbine with non-axisymmetric endwall contouring has been numerically investigated. For this purpose, the geometry and boundary condition of a three-stage turbine at the Turbomachinery Performance and Flow Research Laboratory (TPFL), Texas A&M University is utilized. The turbine is being prepared to experimentally verify the results of the current numerical investigations. Its rotor includes non-axisymmetric endwall contouring on the first and second rotor row. In the preceding paper [1] it was shown that the endwall contouring of the second rotor contouring was able to substantially increase the turbine efficiency. To investigate the film cooling in conjunction with a purge flow injection, the first turbine rotor hub was contoured. Applying the same contouring method, however, different aerodynamic behavior of the first rotor was observed due to its immediate exposure to the purge flow injection. Consequently, the endwall design of the first rotor row required particular attention. The purge flow investigation involves the reference case without endwall contouring followed by the investigation with endwall contouring. The turbine used for this numerical investigation has two independent cooling loops. The first loop supplies coolant air to the stator-rotor gap, while the second loop provides cooling air to the downstream discrete film-cooling holes and blade tip cooling injection holes. For the current investigations the second loop is closed. Film cooling effectiveness is numerically simulated for rotor frequency of 2400 rpm. Efficiency, pressure, temperature and film cooling effectiveness distributions are determined for purge mass flow ratios of MFR = 0.5%, 1.0% and 2.0%. The small amount of the injected mass flow drastically changes the development of the secondary flow structure of the contoured first turbine row partially reversing the improvement tendency obtained from the endwall contouring.

Experimental Investigation of the Effect of Purge Flow on Film Cooling Effectiveness on a Rotating Turbine With Non-Axisymmetric Endwall Contouring

2013 ◽  
Author(s):  
M. Rezasoltani ◽  
M. T. Schobeiri ◽  
J. C. Han
Keyword(s):  
Experimental Investigation ◽  
Film Cooling ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Efficiency ◽  
Purge Flow ◽  
Endwall Contouring ◽  
And Performance ◽  
Cooling Loops ◽  
The Impact

The impact of the purge flow injection on aerodynamics and film cooling effectiveness of a three-stage high pressure turbine with non-axisymmetric endwall contouring has been experimentally investigated. As a continuation of the previously published work involving stator-rotor gap purge cooling, this study investigates film cooling effectiveness on the first stage rotor contoured platform due to a coolant gas injection. Film cooling effectiveness measurements are performed on the rotor blade platform using a pressure sensitive paint (PSP) technique. The present study examines, in particular, the film cooling effectiveness due to injection of coolant from the rotor cavity through the circumferential gap between the first stator followed by the first rotor. Efficiency and performance experiments were conducted with and without cooling injection to show (a) the impact of endwall contouring on the turbine efficiency and (b) the impact of film cooling injection in association with the endwall contouring. The experimental investigation is carried out in a three-stage turbine facility at the Turbomachinery Performance and Flow Research Laboratory (TPFL) at Texas A&M University. Its rotor includes non-axisymmetric endwall contouring on the first and second rotor row [1]. The turbine has two independent cooling loops. Film cooling effectiveness measurements are performed for three coolant-to-mainstream mass flow ratios of 0.5%, 1.0% and 1.5%. Film cooling data is also obtained for three rotational speeds, 3000 rpm (reference condition), 2550 rpm and 2400 rpm and compared with non-contoured endwall data.

Experimental Study on the Effects of Slot Jet on Film Cooling Performance in the Cascade Endwall With Purge Flow

2019 ◽  
Author(s):  
Yao Yunjia ◽  
Zhu Peiyuan ◽  
Tao Zhi ◽  
Song Liming ◽  
Li Jun
Keyword(s):  
Mass Flow ◽  
Film Cooling ◽  
Flow Ratio ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Ejection Angle ◽  
Purge Flow ◽  
Endwall Film Cooling ◽  
Mass Flow Ratio

Abstract Based on the infrared temperature measurement technology, in this paper, the effect of the purge flow from the upstream slot on the film cooling performance of the annular cascade endwall was studied experimentally. GE‘s E3 turbine first stage stator blades is selected as the experimental reference blade type in this experiment. In the current experiment, effects of different slot locations, slot ejection angles and slot profiles on the endwall film cooling effectiveness were taken into account. Under the influence of endwall secondary flow, the film cooling is mainly concentrated on the front part of the channel and close to the suction side of the blade, while there is almost no cooling effect close to the pressure side of the blade in the channel. With the increase of the distance between the blade leading edge and the slot, the endwall film cooling performance is reduced. While the distance increasing from 0.15Cx to 0.45Cx, and the peak endwall film cooling effectiveness is reduced by 78%, 68% and 58% respectively when the mass flow ratio (MFR) is 1.0%, 1.5%, and 2.0%. As the slot ejection angle is reduced, the endwall film cooling performance can be effectively improved. When the slot ejection angle increased from 45° to 90°, the peak endwall film cooling effectiveness decreases by 17%, 15%, and 13% respectively at the mass flow ratio (MFR) = 1.0%,1.5% and 2.0%. And the convergent slot can effectively improve the endwall cooling film formed by slot jet compared to the reference slot. When the mass flow ratio are MFR = 1.0%, 1.5%, and 2.0%, the peak endwall film cooling effectiveness at the convergent slot is increased by 50%, 20%, and 15% comparing to the reference slot.

A Combined Numerical and Experimental Study of the Effect of Non-Axisymmetric Contouring on Performance and Film Cooling Behavior of a Rotating Turbine Endwall

2014 ◽  
Author(s):  
K. Lu ◽  
M. Rezasoltani ◽  
M. T. Schobeiri ◽  
J. C. Han
Keyword(s):  
Rotational Speed ◽  
Film Cooling ◽  
Experimental Investigations ◽  
Performance Measurements ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Turbine Efficiency ◽  
Speed Performance ◽  
Endwall Contouring ◽  
The Impact

Applying a new non-axisymmetric endwall contouring technology introduced by Turbomachinery Performance and Flow Research Laboratory (TPFL) at Texas A&M University to the second rotor row of a three-stage research turbine, has shown that for a single rotor row a major turbine efficiency improvement can be achieved [1]. Motivated by these results, comprehensive numerical and experimental investigations on the TPFL research turbine were conducted to determine the impact of the endwall contouring on film cooling effectiveness. For this investigation, the first rotor row directly subjected to the purge flow injection was chosen to which the new contouring technology was applied. Performing an extensive RANS simulation by using the boundary conditions from the experiments, aerodynamics, performance and film cooling effectiveness studies were performed by varying the injection blowing ratio and turbine rotational speed. Performance measurements were carried out within a rotational speed range of 1800 to 3000 RPM. The corresponding CFD simulations were carried out for four rotational speeds, 2000, 2400, 2600, and 3000 rpm. Comparison of the RANS aerodynamics simulation with experiments reveals noticeable differences. Considering the film cooling effectiveness, major differences between experiment and numerical results were observed and discussed in the paper.

Experimental Investigation of the Effect of Purge Flow on Film Cooling Effectiveness on a Rotating Turbine With Nonaxisymmetric End Wall Contouring

2014 ◽  
Vol 136 (9) ◽  
Author(s):  
M. Rezasoltani ◽  
M. T. Schobeiri ◽  
J. C. Han
Keyword(s):  
Experimental Investigation ◽  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Pressure Sensitive ◽  
Purge Flow ◽  
Cooling Loops ◽  
End Wall ◽  
The Impact

The impact of the purge flow injection on aerodynamics and film cooling effectiveness of a three-stage, high-pressure turbine with nonaxisymmetric end wall contouring has been experimentally investigated. As a continuation of the previously published work involving stator-rotor gap purge cooling, this study investigates film cooling effectiveness on the first-stage rotor contoured platform due to a coolant gas injection. Film cooling effectiveness measurements are performed on the rotor blade platform using a pressure-sensitive paint (PSP) technique. The present study examines, in particular, the film cooling effectiveness due to injection of coolant from the rotor cavity through the circumferential gap between the first stator followed by the first rotor. Effects of the presence of contouring, blowing ratios, rotational speeds, and coolant density ratio are studied and compared to a noncontouring platform. The experimental investigation is carried out in a three-stage turbine facility at the Turbomachinery Performance and Flow Research Laboratory (TPFL) at Texas A&M University. Its rotor includes nonaxisymmetric end wall contouring on the first and second rotor row. The turbine has two independent cooling loops. Film cooling effectiveness measurements are performed for three coolant-to-mainstream mass flow ratios of 0.5%, 1.0%, and 1.5%. Film cooling data is obtained for three rotational speeds, 3000 rpm (reference condition), 2550 rpm, and 2400 rpm, and compared with noncontoured end wall data. Effect of density ratio for coolant-to-mainstream density ratio (DR) = 1.0 and DR = 1.5 is also investigated. The comparisons of film effectiveness results show that contoured cases have a noticeable quantitative improvement compared to those of noncontoured ones.

Influence of Coolant Jet Pulsation on the Convective Film Cooling of an Adiabatic Wall

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Qaiser Sultan ◽  
Gildas Lalizel ◽  
Matthieu Fénot ◽  
Eva Dorignac
Keyword(s):  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Film Cooling ◽  
Convective Heat Transfer Coefficient ◽  
Time Interval ◽  
Adiabatic Wall ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
The Impact

This study investigates the effects of sinusoidal pulsations externally imposed to an oblique round jet. The effectiveness of film coverage of an adiabatic wall onset for a thermally uniform bulk flow is presented in the perspective of gas turbine film cooling. For the injectant fluid, both the temperature and the mass flow rate are controlled prior to entrance to the periodic forcing system using a loudspeaker drive. The characteristic film cooling parameters including the blowing ratios and the temperature ratio are maintained at M=ρiUi/ρ∞U∞ = 0.65, 1, and 1.25, and Ti/T∞=2 respectively. The injection fluid is pulsated to a nondimensionalized frequency of St=f⋅d/U = 0, 0.2, 0.3, and 0.5. In the present investigation, the impact of injectant film modulation is figured out by analyzing the velocity fields measured by a system of time-resolved particle image velocimetry (TR-PIV), as well as analyzing the adiabatic wall temperature and the convective heat transfer coefficient measured by a system of infrared thermography. The overall film-cooling effectiveness is revealed by the time-averaged analysis, in which altered time-averaged jet trajectories and wake behavior are focused. It is observed that the pulsations tend to result in lower effectiveness when the flow remained attached to the wall in steady blowing case. In steady blowing cases with jet liftoff, such as for M= 1.25, rendering low-frequency pulsation helps in increasing film-cooling effectiveness due to the discharge of lower mass flow rate coolant during the significant time interval of the respective pulse cycle.

Influence of Coolant Density on Turbine Platform Film-Cooling With Stator–Rotor Purge Flow and Compound-Angle Holes

2014 ◽  
Vol 6 (4) ◽  
Author(s):  
Kevin Liu ◽  
Shang-Feng Yang ◽  
Je-Chin Han
Keyword(s):  
Film Cooling ◽  
Density Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Fundamental Parameters ◽  
Blowing Ratio ◽  
Purge Flow ◽  
Cylindrical Holes ◽  
Exit Mach Number ◽  
Compound Angle

A detailed parametric study of film-cooling effectiveness was carried out on a turbine blade platform. The platform was cooled by purge flow from a simulated stator–rotor seal combined with discrete hole film-cooling. The cylindrical holes and laidback fan-shaped holes were accessed in terms of film-cooling effectiveness. This paper focuses on the effect of coolant-to-mainstream density ratio on platform film-cooling (DR = 1 to 2). Other fundamental parameters were also examined in this study—a fixed purge flow of 0.5%, three discrete-hole film-cooling blowing ratios between 1.0 and 2.0, and two freestream turbulence intensities of 4.2% and 10.5%. Experiments were done in a five-blade linear cascade with inlet and exit Mach number of 0.27 and 0.44, respectively. Reynolds number of the mainstream flow was 750,000 and was based on the exit velocity and chord length of the blade. The measurement technique adopted was the conduction-free pressure sensitive paint (PSP) technique. Results indicated that with the same density ratio, shaped holes present higher film-cooling effectiveness and wider film coverage than the cylindrical holes, particularly at higher blowing ratios. The optimum blowing ratio of 1.5 exists for the cylindrical holes, whereas the effectiveness for the shaped holes increases with an increase of blowing ratio. Results also indicate that the platform film-cooling effectiveness increases with density ratio but decreases with turbulence intensity.

Numerical Investigation of Film Cooling Effectiveness Including Shockwave Interaction in a Supersonic Nozzle Flow

2022 ◽  
Author(s):  
Manoj Prabakar Sargunaraj ◽  
Andres Torres ◽  
Jose Garduna ◽  
Marcel Otto ◽  
Jayanta S. Kapat ◽  
...  
Keyword(s):  
Numerical Investigation ◽  
Film Cooling ◽  
Supersonic Nozzle ◽  
Nozzle Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness

Account of Film Turbulence for Predicting Film Cooling Effectiveness in Gas Turbine Combustors

1979 ◽  
Author(s):  
G. J. Sturgess
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Cooling Effectiveness ◽  
Turbine Engine ◽  
Film Cooling Effectiveness ◽  
Wide Range ◽  
Engine Combustion ◽  
Turbulence Effects ◽  
The Impact ◽  
Combustor Liner

The paper deals with a small but important part of the overall gas turbine engine combustion system and continues earlier published work on turbulence effects in film cooling to cover the case of film turbulence. Film cooling of the gas turbine combustor liner imposes certain geometric limitations on the coolant injection device. The impact of practical film injection geometry on the cooling is one of increased rates of film decay when compared to the performance from idealized injection geometries at similar injection conditions. It is important to combustor durability and life estimation to be able to predict accurately the performance obtainable from a given practical slot. The coolant film is modeled as three distinct regions, and the effects of injection slot geometry on the development of each region are described in terms of film turbulence intensity and initial circumferential non-uniformity of the injected coolant. The concept of the well-designed slot is introduced and film effectiveness is shown to be dependent on it. Only slots which can be described as well-designed are of interest in practical equipment design. A prediction procedure is provided for well-designed slots which describes growth of the film downstream of the first of the three film regions. Comparisons of predictions with measured data are made for several very different well-designed slots over a relatively wide range of injection conditions, and good agreement is shown.

Film Cooling Effectiveness on a Rotating Turbine Platform Using Pressure Sensitive Paint Technique

2007 ◽  
Author(s):  
A. Suryanarayanan ◽  
B. Ozturk ◽  
M. T. Schobeiri ◽  
J. C. Han
Keyword(s):  
Film Cooling ◽  
Gas Injection ◽  
Turbine Rotor ◽  
Pressure Sensitive Paint ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Pressure Sensitive ◽  
Coolant Injection ◽  
Purge Flow ◽  
Effects Of Rotation

Film cooling effectiveness is measured on a rotating turbine blade platform for coolant injection through discrete holes using pressure sensitive paint technique (PSP). Most of the existing literatures provide information only for stationary end-walls. The effects of rotation on the platform film cooling effectiveness are not well documented. Hence, the existing 3-stage turbine research facility at TPFL, Texas A&M University was re-designed and installed to enable coolant gas injection on the 1st stage rotor platform. Two distinct coolant supply loops were incorporated into the rotor to facilitate separate feeds for upstream cooling using stator-rotor gap purge flow and downstream discrete-hole film cooling. As a continuation of the previously published work involving stator-rotor gap purge cooling, this study investigates film cooling effectiveness on the 1st stage rotor platform due to coolant gas injection through nine discrete holes located downstream within the passage region. Film cooling effectiveness is measured for turbine rotor frequencies of 2400rpm, 2550rpm and 3000rpm corresponding to rotation numbers of Ro = 0.18, 0.19 and 0.23 respectively. For each of the turbine rotational frequencies, film cooling effectiveness is determined for average film-hole blowing ratios of Mholes = 0.5, 0.75, 1.0, 1.25, 1.5 and 2.0. To provide a complete picture of hub cooling under rotating conditions, simultaneous injection of coolant gas through upstream stator-rotor purge gap and downstream discrete film-hole is also studied. The combined tests are conducted for gap purge flow corresponding to coolant to mainstream mass flow ratio of MFR = 1% with three downstream film-hole blowing ratios of Mholes = 0.75, 1.0 and 1.25 for each of the three turbine speeds. The results for combined upstream stator-rotor gap purge flow and downstream discrete holes provide information about the optimum purge flow coolant mass, average coolant hole blowing ratios for each rotational speed and coolant injection location along the passage to obtain efficient platform film cooling.

Sign in / Sign up

Export Citation Format

Share Document