Numerical Investigation on Flow and Heat Transfer in Matrix Cooling Channels for Turbine Blades

2016 ◽  
Author(s):  
Yigang Luan ◽  
Shi Bu ◽  
Haiou Sun ◽  
Tao Sun
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Pressure Drop ◽  
Heat Transfer Performance ◽  
Structural Parameters ◽  
Turbine Blades ◽  
Channel Width ◽  
Transfer Performance ◽  
Cooling Channel ◽  
Cooling Channels

Matrix cooling is one kind of internal cooling structures applied to protect turbine blades. This paper investigated the flow field and heat transfer performance in matrix cooling channels experimentally and numerically. A testing section (rib angle of 45-deg, rib thickness of 30mm, rib height of 30mm and sub-channel width of 30mm) made of Plexiglas was build and connected to a wind tunnel sysytem. And Transient Liquid Crystal (TLC) technique was applied to obtain the detailed heat transfer distribution on the primary surface inside the matrix cooling channel. The experiment was performed under different Reynolds numbers varying from 18428 to 28327, based on the channel inlet hydraulic diameter; also the overall pressure drop across the channel was measured. Experimental results were used to calibrate the numerical solution obtained by computational fluid dynamics (CFD) method. During the numerical simulation process, structured grids and k-w turbulence model was employed. And a good agreement is obtained between experimental and CFD results for both pressure drop and heat transfer performance. Channels of various structural parameters (rib angle, rib thickness and sub-channel width) were then studied by numerical simulation, three rib angles (30-deg, 45-deg and 60-deg), three rib thicknesses (1.8mm, 3mm and 5mm) and three sub-channel widths (3mm, 5mm and 9mm) were considered, with the rib height 3mm for all the cases. Numerical results showed that the sidewall turnings made the greatest contribution to heat transfer enhancement but caused very large pressure drop meanwhile. The overall heat transfer and pressure drop increase with rib angle and rib width but decrease with sub-channel width. The thermal performance factor decreases with rib angle and rib width, while it showed a non-monotonic dependency on sub-channel width. Among the three structural parameters, rib angle has the most significant effect on the performance of matrix cooling channel.

Optimization of a U-Bend for Minimal Pressure Loss in Internal Cooling Channels—Part II: Experimental Validation

2013 ◽  
Vol 135 (5) ◽  
Author(s):  
Filippo Coletti ◽  
Tom Verstraete ◽  
Jérémy Bulle ◽  
Timothée Van der Wielen ◽  
Nicolas Van den Berge ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Loss ◽  
Heat Transfer Performance ◽  
Internal Cooling ◽  
Transfer Performance ◽  
Cooling Channel ◽  
Piv Measurements ◽  
Cooling Channels ◽  
Numerical Predictions ◽  
The Impact

This two-part paper addresses the design of a U-bend for serpentine internal cooling channels optimized for minimal pressure loss. The total pressure loss for the flow in a U-bend is a critical design parameter, as it augments the pressure required at the inlet of the cooling system, resulting in a lower global efficiency. In the first part of the paper, the design methodology of the cooling channel was presented. In this second part, the optimized design is validated. The results obtained with the numerical methodology described in Part I are checked against pressure measurements and particle image velocimetry (PIV) measurements. The experimental campaign is carried out on a magnified model of a two-legged cooling channel that reproduces the geometrical and aerodynamical features of its numerical counterpart. Both the original profile and the optimized profile are tested. The latter proves to outperform the original geometry by about 36%, in good agreement with the numerical predictions. Two-dimensional PIV measurements performed in planes parallel to the plane of the bend highlight merits and limits of the computational model. Despite the well-known limits of the employed eddy viscosity model, the overall trends are captured. To assess the impact of the aerodynamic optimization on the heat transfer performance, detailed heat transfer measurements are carried out by means of liquid crystals thermography. The optimized geometry presents overall Nusselt number levels only 6% lower with respect to the standard U-bend. The study demonstrates that the proposed optimization method based on an evolutionary algorithm, a Navier–Stokes solver, and a metamodel of it is a valid design tool to minimize the pressure loss across a U-bend in internal cooling channels without leading to a substantial loss in heat transfer performance.

Effect of Protuberances in the Heat Transfer Enhancement in Mini-Channels

2021 ◽  
Author(s):  
Ariel Cruz Diaz ◽  
Gerardo Carbajal
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Pressure Drop ◽  
Heat Transfer Enhancement ◽  
Heat Transfer Performance ◽  
Heat Removal ◽  
Working Fluid ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Mini Channels

Abstract This study presents the effects of adding an array of protrusions in a microchannel for heat transfer enhancement. The presence of mini-channels increases the overall heat transfer area and boosts the mixing development near the solid-fluid interaction; therefore, it can remove more heat than conventional mini-channels without protuberances. A numerical study proved that protuberances in a mini-channel increase the heat transfer performance by disturbing the relative fluid motion near the solid wall. The numerical simulation was performed with three different protuberances arrays: aligned, staggered, and angular. Each array consists of a thin flat plate with a hemispherical shape; the working fluid and the solid materials were water and copper. The study also includes the effect of different Reynolds numbers: 1,000, 1,500, and 2,000. Three heat inputs were applied in the numerical simulation; these were 1W, 3W, and 5W. The study was compared with a simple microchannel with non-protuberances to analyze the microchannel performance regarding heat removal and pressure drop. For heat transfer performance, the best array was the staggering array with a maximum heat removal increase of 5.26 percent. In terms of pressure drop performance, the best array was the aligned array, with a maximum increase of 34.73 percent.

Research on the Effects of Dimples and Protrusions on Flow and Heat Transfer in Matrix Cooling Channels in Turbine Blades

2019 ◽  
Author(s):  
Yigang Luan ◽  
Lianfeng Yang ◽  
Yue Yin ◽  
Pietro Zunino
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Heat Transfer Performance ◽  
Turbine Blades ◽  
Inlet Temperature ◽  
Transfer Performance ◽  
Turbine Inlet Temperature ◽  
Turbine Engine ◽  
Cooling Channels ◽  
Flow And Heat Transfer

Abstract Nowadays, gas turbine engines play an indispensable role in modern industry, which have been widely used especially in the aviation, marine and energy fields. The turbine inlet temperature is one of the most important factors that influences the performance of the turbine engine. It’s acknowledged that the higher turbine inlet temperature contributes to the overall gas turbine engine efficiency. Therefore, the internal cooling technology of turbine blades is of vital importance. This paper mainly studies the effects of dimples and protrusions on flow and heat transfer in matrix cooling channels and optimize the performance of the matrix cooling structure by numerical simulation and experiment methods. Thirteen cases have been calculated under Re = 10,000∼80,000 by the commercial code ANSYS Fluent. Structures with different layouts of dimples and protrusions were considered, such as the number, distance and the depth ratio. The original model has been strengthened due to the dimple and protrusion structure, which improves heat transfer performance as well as the thermal performance factor (TPF) on condition that the pressure loss increases slightly. Meanwhile, the optimized structures have been made and tested by the transient liquid crystal technique (TLC). A comparison between the CFD results and the experimental data is made. Note that the heat transfer performance is much better when the ratio of the dimple depth and the dimple diameter is equal to 0.3, compared with the ratio of 0.1 and 0.2. In terms of the cases with two sides dimples, the heat transfer can be enhanced by increasing the number of the dimples. In addition, the heat transfer performance is the best when both of dimples and protrusions are applied. Nu/Nu0 and TPF increase by up to approximately 7% and 5% respectively.

scholarly journals Optimization Design of Lattice Structures in Internal Cooling Channel with Variable Aspect Ratio of Gas Turbine Blade

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3954
Author(s):  
Liang Xu ◽  
Qicheng Ruan ◽  
Qingyun Shen ◽  
Lei Xi ◽  
Jianmin Gao ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Aspect Ratio ◽  
Optimization Model ◽  
Lattice Structure ◽  
Turbine Blades ◽  
Internal Cooling ◽  
Cooling Channel ◽  
Cooling Channels ◽  
Mechanical Performances ◽  
Type Lattice

Traditional cooling structures in gas turbines greatly improve the high temperature resistance of turbine blades; however, few cooling structures concern both heat transfer and mechanical performances. A lattice structure (LS) can solve this issue because of its advantages of being lightweight and having high porosity and strength. Although the topology of LS is complex, it can be manufactured with metal 3D printing technology in the future. In this study, an integral optimization model concerning both heat transfer and mechanical performances was presented to design the LS cooling channel with a variable aspect ratio in gas turbine blades. Firstly, some internal cooling channels with the thin walls were built up and a simple raw of five LS cores was taken as an insert or a turbulator in these cooling channels. Secondly, relations between geometric variables (height (H), diameter (D) and inclination angle(ω)) and objectives/functions of this research, including the first-order natural frequency (freq1), equivalent elastic modulus (E), relative density (ρ¯) and Nusselt number (Nu), were established for a pyramid-type lattice structure (PLS) and Kagome-type lattice structure (KLS). Finally, the ISIGHT platform was introduced to construct the frame of the integral optimization model. Two selected optimization problems (Op-I and Op-II) were solved based on the third-order response model with an accuracy of more than 0.97, and optimization results were analyzed. The results showed that the change of Nu and freq1 had the highest overall sensitivity Op-I and Op-II, respectively, and the change of D and H had the highest single sensitivity for Nu and freq1, respectively. Compared to the initial LS, the LS of Op-I increased Nu and E by 24.1% and 29.8%, respectively, and decreased ρ¯ by 71%; the LS of Op-II increased Nu and E by 30.8% and 45.2%, respectively, and slightly increased ρ¯; the LS of both Op-I and Op-II decreased freq1 by 27.9% and 19.3%, respectively. These results suggested that the heat transfer, load bearing and lightweight performances of the LS were greatly improved by the optimization model (except for the lightweight performance for the optimal LS of Op-II, which became slightly worse), while it failed to improve vibration performance of the optimal LS.

Heat Transfer Performance of Different Nanofluids Flows in a Helically Coiled Heat Exchanger

2013 ◽  
Vol 832 ◽  
pp. 160-165 ◽  
Author(s):  
Mohammad Alam Khairul ◽  
Rahman Saidur ◽  
Altab Hossain ◽  
Mohammad Abdul Alim ◽  
Islam Mohammed Mahbubul
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Pressure Drop ◽  
Transfer Coefficient ◽  
Friction Factor ◽  
Heat Exchangers ◽  
Heat Transfer Performance ◽  
Volume Concentration ◽  
Transfer Performance

Helically coiled heat exchangers are globally used in various industrial applications for their high heat transfer performance and compact size. Nanofluids can provide excellent thermal performance of this type of heat exchangers. In the present study, the effect of different nanofluids on the heat transfer performance in a helically coiled heat exchanger is examined. Four different types of nanofluids CuO/water, Al2O3/water, SiO2/water, and ZnO/water with volume fractions 1 vol.% to 4 vol.% was used throughout this analysis and volume flow rate was remained constant at 3 LPM. Results show that the heat transfer coefficient is high for higher particle volume concentration of CuO/water, Al2O3/water and ZnO/water nanofluids, while the values of the friction factor and pressure drop significantly increase with the increase of nanoparticle volume concentration. On the contrary, low heat transfer coefficient was found in higher concentration of SiO2/water nanofluids. The highest enhancement of heat transfer coefficient and lowest friction factor occurred for CuO/water nanofluids among the four nanofluids. However, highest friction factor and lowest heat transfer coefficient were found for SiO2/water nanofluids. The results reveal that, CuO/water nanofluids indicate significant heat transfer performance for helically coiled heat exchanger systems though this nanofluids exhibits higher pressure drop.

A Study on Flow Boiling in Microchannel With Piranha Pin Fin

2015 ◽  
Author(s):  
X. Yu ◽  
C. Woodcock ◽  
Y. Wang ◽  
J. Plawsky ◽  
Y. Peles
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Fluid Flow ◽  
Pressure Drop ◽  
Heat Transfer Performance ◽  
Flow Boiling ◽  
Transfer Performance ◽  
Flow Conditions ◽  
Pin Fin ◽  
Flow And Heat Transfer

In this paper we reported an advanced structure, the Piranha Pin Fin (PPF), for microchannel flow boiling. Fluid flow and heat transfer performance were evaluated in detail with HFE7000 as working fluid. Surface temperature, pressure drop, heat transfer coefficient and critical heat flux (CHF) were experimentally obtained and discussed. Furthermore, microchannels with different PPF geometrical configurations were investigated. At the same time, tests for different flow conditions were conducted and analyzed. It turned out that microchannel with PPF can realize high-heat flux dissipation with reasonable pressure drop. Both flow conditions and PPF configuration played important roles for both fluid flow and heat transfer performance. This study provided useful reference for further PPF design in microchannel for flow boiling.

scholarly journals Entropy Generation and Heat Transfer Performance in Microchannel Cooling

Entropy ◽  
2019 ◽  
Vol 21 (2) ◽  
pp. 191 ◽  
Author(s):  
Jundika Kurnia ◽  
Desmond Lim ◽  
Lianjun Chen ◽  
Lishuai Jiang ◽  
Agus Sasmito
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Heat Transfer Performance ◽  
Second Law Of Thermodynamics ◽  
High Heat ◽  
Heat Fluxes ◽  
Transfer Performance ◽  
Cooling Channel ◽  
High Heat Transfer ◽  
Microchannel Cooling

Owing to its relatively high heat transfer performance and simple configurations, liquid cooling remains the preferred choice for electronic cooling and other applications. In this cooling approach, channel design plays an important role in dictating the cooling performance of the heat sink. Most cooling channel studies evaluate the performance in view of the first thermodynamics aspect. This study is conducted to investigate flow behaviour and heat transfer performance of an incompressible fluid in a cooling channel with oblique fins with regards to first law and second law of thermodynamics. The effect of oblique fin angle and inlet Reynolds number are investigated. In addition, the performance of the cooling channels for different heat fluxes is evaluated. The results indicate that the oblique fin channel with 20° angle yields the highest figure of merit, especially at higher Re (250–1000). The entropy generation is found to be lowest for an oblique fin channel with 90° angle, which is about twice than that of a conventional parallel channel. Increasing Re decreases the entropy generation, while increasing heat flux increases the entropy generation.

Sign in / Sign up

Export Citation Format

Share Document