Study on Subsynchronous Vibration With Tilting Pad Journal Bearing Under Starved Lubrication

2018 ◽  
Author(s):  
Rimpei Kawashita ◽  
Tadasuke Nishioka ◽  
Shimpei Yokoyama ◽  
Makoto Iwasaki ◽  
Shuichi Isayama ◽  
...  
Keyword(s):  
Flow Rate ◽  
Journal Bearing ◽  
Damping Ratio ◽  
Leading Edge ◽  
Rotor System ◽  
Experimental Results ◽  
Oil Film ◽  
Tilting Pad ◽  
Oil Flow ◽  
Starved Lubrication

Industrial machines such as gas and steam turbines require high efficiency and reliability. Direct lubricated bearings have been developed and installed to reduce mechanical losses. In recent years, it has been reported in the literature that subsynchronous vibration can occur to rotor shafts with direct lubricated tilting pad journal bearings under reduced oil flow rate conditions. In this study, a test rig with a 200 mm diameter and 3.5 meter long rotor supported by a direct lubricated tilting two pad journal bearing was constructed. The primary critical speed is 2100rpm and rotational speed is 3600rpm. The oil-starved area, the non-oil film layer region at the leading edge of the bearing pads, was measured by observing oil film pressure in the bearing clearance with pressure transducers on the rotor surface. A sine sweep excitation test was carried out by using an inertial shaker installed on the bearing housing and the damping ratio of the rotor system was measured. Measured data showed that a larger starved area at the leading edge of the bearing pads due to reduced oil feeding results in a smaller damping ratio, and an increase in the natural frequency of the rotor. Experimental results of two types of oil feeding nozzles were compared with respect to the correlation between starved area and damping ratio of the rotor system, and a relationship between oil flow rate and starved area was discussed. A method for modeling bearing coefficients under starved lubrication has been proposed based on thermo-hydrodynamic lubrication (THL) analysis. A numerical analysis of a finite element-transfer matrix model of the test rotor with the bearing coefficients calculated by the proposed method is carried out, and it is found that the analytical results are in broad agreement with the experimental results.

Oil Flow in a Full Journal Bearing

1961 ◽  
Vol 83 (2) ◽  
pp. 312-314
Author(s):  
Donald F. Hays
Keyword(s):  
Flow Rate ◽  
Journal Bearing ◽  
Hydrodynamic Pressure ◽  
Leakage Rate ◽  
Positive Pressure ◽  
Pressure Gradients ◽  
Oil Film ◽  
Oil Flow ◽  
Pressure Area ◽  
Side Flow

An analysis was made of the oil flows occurring in a full journal bearing with a continuous oil film. The flow rate into the bearing was determined at the section of greatest clearance and the rate of outflow was determined at the section of least clearance. The rate of side flow or leakage rate was determined by considering the flow across the boundary of the positive pressure area only and is the flow resulting from the hydrodynamic pressure gradients. It does not include the effects of any specific oil feed mechanism.

Identification of Dynamic Coefficients of a Five-Pad Tilting Pad Journal Bearing up to Highest Surface Speeds

2020 ◽  
Author(s):  
Philipp Zemella ◽  
Thomas Hagemann ◽  
Bastian Pfau ◽  
Hubert Schwarze
Keyword(s):  
Flow Rate ◽  
Time Domain ◽  
Static Load ◽  
Journal Bearing ◽  
Damping Coefficients ◽  
Dynamic Coefficients ◽  
Tilting Pad ◽  
Oil Flow ◽  
Tilting Pad Journal Bearing ◽  
The Impact

Abstract Tilting-pad journal bearings are widely used in turbomachinery industry due to their positive dynamic properties at high rotor speeds. However, the exact description of this dynamic behavior is still part of current research. This paper presents measurement results for a five-pad tilting-pad journal bearing in load between pivot configuration. The bearing is characterized by a nominal diameter of 100 mm, a length of 90 mm, and a pivot offset of 0.6. Investigations include results for surface speeds between 25 and 120 m/s and specific bearing loads ranging from 0.0 to 3.0 MPa. Results of theoretical predictions are commonly derived from perturbation of stationary operation under static load. Therefore, experimental results for stationary operation including pad deflection under static load are presented first to characterize the investigated bearing. Measured results indicate considerable non-laminar flow in the upper region of the investigated range of rotor speeds. Second, dynamic excitation test are performed with excitation frequencies up to 400 Hz to evaluate dynamic coefficients of a stiffness (K) and damping (C) KC-model, and additionally, a KCM-model using additional virtual mass (M) coefficients. KCM-coefficients are obtained by fitting frequency dependent KC-characteristics to the KCM-model structure using least square approach. The wide range of rotating and excitation frequencies leads to subsynchronous as well as supersynchronous vibrations. Excitation forces are applied with multi-sinus and single-sinus characteristics. The latter one allows evaluation of KC-coefficients at the particular frequency ratio in the time domain. Here, frequency and time domain evaluation algorithms for dynamic coefficients are used in order to assess their special properties and quality. The impact of surface speed, bearing load, and oil flow rate on measured and predicted KCM-coefficients is investigated. Measured and predicted results can be well fitted to a KCM-model and show a significant influence of the ratio between fluid film and pivot support stiffness on the speed dependent characteristic of bearing stiffness coefficients. However, the impact of this ratio on damping coefficients is considerably lower. Further investigations on the impact of oil flow rates indicate that a significant decrease of direct damping coefficients exists below a certain level of starvation. Above this limit, direct damping coefficients are nearly independent of oil flow rate. Results are analyzed in detail and demands on improvements for predictions are derived.

Pad attitude adjusting moment in large multi-pocket pivoted pad used in static oil journal bearing

2017 ◽  
Vol 69 (4) ◽  
pp. 605-611
Author(s):  
Xizhi Ma ◽  
Miaomiao Li
Keyword(s):  
Flow Rate ◽  
Ball Mill ◽  
Large Scale ◽  
Journal Bearing ◽  
Operating Conditions ◽  
Content Type ◽  
Oil Film ◽  
Hydrostatic Bearing ◽  
Attitude Adjustment ◽  
Oil Flow

Purpose Large scale is a trend of the ball mill, so the loads on their bearings become very large, bearing operating conditions turn into more severe. The moment of inertia to their pivot of the pad increase significantly, so it leads to the difficult of the pad attitude adjustment and makes the pad tilting angles time response slow, the key factor to effects attitude adjustment is the oil film moment to the pad pivot at unbalance position. the oil film moment and its effect factors must be studied in the design of the bearing used in ball mill. Design/methodology/approach Models about the lubrication of multi-pocket pivoted pad hydrostatic bearing is established, the complicated relationship of the oil flow rate between the oil pockets are taken into account. Finite differential method is used to solv the model, and theroy of finite element method is use to calculate the oil flow rate out of the pocket edges. Newton’s methods are used to determine the pressure of pockets.The pad tilting moment to its pivot is numerically analyzed. Findings The tilting moment to its pivot is set as an indicator of the ability for a pad to adjust its attitude. The effects of the diameter of throttling capillary and the pocket area on the attitude adjusting capacity is studied. Relations between the attitude adjustment capacity for a pad and there effects factors are presented. Practical implications The methods and results have the special reference to the design and operation of multiple pockets tilted pad hydrostatic journal bearing. Originality/value Methods to studied the pad attitude adjustment are given in the article for the multi-pocket pivot pad hydrostatic beairng.The influence factors on pad attitude adjusting capacity are discussed for a this specail kind hydrostatic bearing, the how the factors influence the pad tilting angle adjustment are presented.

Identification of Dynamic Coefficients of a Five-Pad Tilting Pad Journal Bearing Up to Highest Surface Speeds

2021 ◽  
Author(s):  
Philipp Zemella ◽  
Thomas Hagemann ◽  
Bastian Pfau ◽  
Hubert Schwarze
Keyword(s):  
Flow Rate ◽  
Journal Bearing ◽  
Flow Rates ◽  
Damping Coefficients ◽  
Dynamic Coefficients ◽  
Tilting Pad ◽  
Oil Flow ◽  
Bearing Loads ◽  
Tilting Pad Journal Bearing ◽  
The Impact

Abstract This paper presents measurement results for a five-pad tilting-pad journal bearing in load between pivot configuration. The bearing is characterized by a nominal diameter of 100 mm, a length of 90 mm, and a pivot offset of 0.6. Investigations include results for surface speeds between 25 and 120 m/s and specific bearing loads ranging from 0.0 to 3.0 MPa and different lube oil flow rates. Dynamic excitation test are performed with excitation frequencies up to 400 Hz to evaluate dynamic coefficients of a stiffness (K) and damping (C) KC-model, and additionally, a KCM-model using additional virtual mass (M) coefficients. The impact of surface speed, bearing load, and oil flow rate on measured and predicted KCM-coefficients is investigated. Measured and predicted results can be well fitted to a KCM-model and show a significant influence of the ratio between fluid film and pivot support stiffness on the speed dependent characteristic of bearing stiffness coefficients. However, the impact of this ratio on damping coefficients is considerably lower. Further investigations on the impact of oil flow rates indicate that a significant decrease of direct damping coefficients exists below a certain level of starvation. Above this limit, direct damping coefficients are nearly independent of oil flow rate. Results are analyzed in detail and demands on improvements for predictions are derived.

Cooling Effect and Dynamic Characteristics of Oil Film of Partial Tilting Pad Bearing

2007 ◽  
Author(s):  
Kyung-Bo Bang ◽  
Jeong-Hun Kim ◽  
Cheol-Hong Kim
Keyword(s):  
Dynamic Characteristics ◽  
Journal Bearing ◽  
Hydrodynamic Pressure ◽  
Oil Film ◽  
Rotating Speed ◽  
Damping Coefficients ◽  
Tilting Pad ◽  
Oil Flow ◽  
Stiffness And Damping ◽  
Tilting Pad Journal Bearing

In the present paper, we suggest a new type of tilting pad journal bearing to decrease oil film temperature and eliminate pad fluttering during operation. This bearing consists of tilting pad journal bearing at low casing and fixed arc type journal bearing at upper casing. Namely we changed a tilting pad bearing with a fixed arc type bearing at upper casing. To investigate the effects of changing the bearing shape, the static and dynamic characteristics were compared experimentally with conventional tilting pad journal bearing. For the static characteristics, oil film temperature, hydrodynamic pressure and oil film thickness were measured with the variation of rotating speed, bearing load and oil flow rate. The stiffness and damping coefficients of oil film were also obtained using the response subjected to harmonic external force to evaluating the dynamic characteristics. The results show that the suggested type of bearing has effect on reducing oil film temperature and increasing stiffness and damping coefficients of oil film.

scholarly journals Study of Injection Method for Maximizing Oil-Cooling Performance of Electric Vehicle Motor with Hairpin Winding

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 747
Author(s):  
Taewook Ha ◽  
Dong Kyu Kim
Keyword(s):  
Electric Vehicle ◽  
Flow Rate ◽  
Film Formation ◽  
Formation Rate ◽  
Cooling Performance ◽  
Oil Film ◽  
Injection Method ◽  
Cooling Method ◽  
Oil Flow ◽  
Oil Injection

The oil injection method was studied to maximize the cooling performance of an electric vehicle motor with a hairpin winding. The cooling performance of the motor using the oil cooling method is proportional to the contact area of the oil and the coil. A numerical analysis was conducted to examine the effect of the spray nozzle type on the oil flow. The dripping nozzle forms the thickest oil film on the coil, making it the most effective for cooling of hairpin-type motors. Subsequently, an experimental study was conducted to optimize the nozzle diameter and number of nozzles. When the inlet diameter and number was 6.35 mm and 6, the oil film formation rate was 53%, yielding the most uniform oil film. Next, an experiment was performed to investigate the effects of the oil temperature and flow rate on the oil flow. The oil film formation rate was the highest (83%) when the oil temperature was 40 °C and the flow rate was 6 LPM.

scholarly journals Multiphase CFD Modeling of External Oil Flow From a Journal Bearing

2018 ◽  
Author(s):  
Martin Berthold ◽  
Hervé Morvan ◽  
Richard Jefferson-Loveday ◽  
Benjamin C. Rothwell ◽  
Colin Young
Keyword(s):  
Boundary Conditions ◽  
Journal Bearing ◽  
Flow Behavior ◽  
Phase Interface ◽  
Numerical Schemes ◽  
Ansys Fluent ◽  
Oil Film ◽  
Reconstruction Scheme ◽  
Geometric Reconstruction ◽  
Oil Flow

High loads and bearing life requirements make journal bearings a potential choice for use in high power, epicyclic gearboxes in jet engines. Particularly in a planetary configuration the kinematic conditions are complex. With the planet gears rotating about their own axis and orbiting around the sun gear, centrifugal forces generated by both motions interact with each other and affect the external flow behavior of the oil exiting the journal bearing. Computational Fluid Dynamics (CFD) simulations using the Volume of Fluid (VoF) method are carried out in ANSYS Fluent [1] to numerically model the two-phase flow behavior of the oil exiting the bearing and merging into the air surrounding the bearing. This paper presents an investigation of two numerical schemes that are available in ANSYS Fluent to track or capture the air-oil phase interface: the geometric reconstruction scheme and the compressive scheme. Both numerical schemes are used to model the oil outflow behavior in the most simplistic approximation of a journal bearing: a representation, rotating about its own axis, with a circumferentially constant, i.e. concentric, lubricating gap. Based on these simplifications, a three dimensional (3D) CFD sector model with rotationally periodic boundaries is considered. A comparison of the geometric reconstruction scheme and the compressive scheme is presented with regards to the accuracy of the phase interface reconstruction and the time required to reach steady state flow field conditions. The CFD predictions are validated against existing literature data with respect to the flow regime, the direction of the predicted oil flow path and the oil film thickness. Based on the findings and considerations of industrial requirements, a recommendation is made for the most suitable scheme to be used. With a robust and partially validated CFD model in place, the model fidelity can be enhanced to include journal bearing eccentricity. Due to the convergent-divergent gap and the resultant pressure field within the lubricating oil film, the outflow behavior can be expected to be very different compared to that of a concentric journal bearing. Naturally, the inlet boundary conditions for the oil emerging from the journal bearing into the external environment must be consistent with the outlet conditions from the bearing. The second part of this paper therefore focuses on providing a method to generate appropriate inlet boundary conditions for external oil flow from an eccentric journal bearing.

Sign in / Sign up

Export Citation Format

Share Document