Analysis of Single-Phase Convective Heat Transfer and System COP at Higher Power Levels in Thermoelectric-Based Hydronic Cooling and Heating Device

2009 ◽  
Author(s):  
Michael J. Kazmierczak ◽  
Abhishek Gupta
Keyword(s):  
Heat Transfer ◽  
Heat Pump ◽  
Flow Rate ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
System Component ◽  
Pump System ◽  
Heat Pump System ◽  
Higher Power ◽  
Te Modules

Experiments were performed on a heat exchanger equipped with multiple thermoelectric (TE) modules. The TE-HX serves as the basic system component in a simple hydronic modular Peltier heat pump system designed to provide chilled or hot water for domestic use (or supplementary building climate control) of small residences [1]. The present work focuses on the detailed convection analysis inside the TE-HX component when 10 thermoelectric modules are utilized. The local heat transfer coefficient at different points along the channel are measured at steady-state, first, when a continuous heater is installed and then when replaced with 10 TE modules. The experimental heat transfer coefficients obtained are compared with available empirical correlations for “transition” (3000 < ReDh < 7000) turbulent flow inside the channel with fair-to-good results. Next, the resulting coefficient-of-performance of the TE heat pump system is measured with its value depending both on system input power and water flow rate. Testing showed that performance degradation, i.e. reduced COPs, occurred when operated at higher power levels but remains satisfactory for up to 688 Watts with higher flow rate.

Experimental Study of Heating-Cooling Combined Ground Source Heat Pump System with Horizontal Ground Heat Exchanger

2011 ◽  
Vol 374-377 ◽  
pp. 398-404 ◽  
Author(s):  
Ying Ning Hu ◽  
Ban Jun Peng ◽  
Shan Shan Hu ◽  
Jun Lin
Keyword(s):  
Heat Exchanger ◽  
Heat Exchange ◽  
Heat Pump ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Ground Heat Exchanger ◽  
Pipe Length ◽  
Pump System ◽  
Heat Pump System ◽  
Heating And Cooling

A hot-water and air-conditioning (HWAC) combined ground sourse heat pump(GSHP) system with horizontal ground heat exchanger self-designed and actualized was presented in this paper. The heat transfer performance for the heat exchanger of two different pipe arrangements, three layers and four layers, respectively, was compared. It showed that the heat exchange quantity per pipe length for the pipe arrangement of three layers and four layers are 18.0 W/m and 15.0 W/m. The coefficient of performance (COP) of unit and system could remain 4.8 and 4.2 as GSHP system for heating water, and the COP of heating and cooling combination are up to 8.5 and 7.5, respectively. The power consumption of hot-water in a whole year is 9.0 kwh/t. The economy and feasibility analysis on vertical and horizontal ground heat exchanger were made, which showed that the investment cost per heat exchange quantity of horizontal ground heat exchanger is 51.4% lower than that of the vertical ground heat exchanger, but the occupied area of the former is 7 times larger than the latter's.

scholarly journals Feasibility Analysis and Performance Evaluation and Optimization of a DXSAHP Water Heater Based on the Thermal Capacity of the System: A Case Study

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3883
Author(s):  
Jorge E. De León-Ruiz ◽  
Ignacio Carvajal-Mariscal ◽  
Antonin Ponsich
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Heat Pump ◽  
Thermal Capacity ◽  
Hot Water ◽  
Outlet Temperature ◽  
Solar Collectors ◽  
Pump System ◽  
Heat Pump System

The present work conducts an evaluation of the feasibility and the overall performance and consequent optimization of a direct expansion solar assisted heat pump (DXSAHP) employed for domestic water heating. For the study conducted R134a, R404A, R407C and R410A working fluids were evaluated as well as the use of four, six and eight flat-plate solar collectors and a worktime ranging from 1 to 6 h. The case study is based in Mexico City with a 300 L container and a hot water outlet temperature of 51 °C. The paper introduces a new evaluation criterion based on the thermal capacity and all the evaluations conducted throughout this research revolve around this performance metric. The results show that, the system would require at least 4 h of operation to achieve the outlet temperature. Additionally, it was found that the R410A refrigerant has the best heat transfer properties; with an average condensation heat rate of 6.31 kW, followed by the R407C with 5.72 kW, the R404A with 5.42 kW and the R134a with 5.18 kW. Diversely, the R134a refrigerant requires 0.402 kW of compression work, 62% less than the R410A, which requires 1.06 kW. Consequently, R134a delivers the highest COP, which ranges from 7 to 14, followed by the R407C and R404A refrigerants, which present a similar behaviour between them, with COP ranging from 5 to 9 and 4 to 8, respectively, and finally the R410A, achieving the lowest COP, ranging from 3.5 to 6.5. Moreover, it was found that the R134a presents a higher dispersion regarding the energy exchange rate, which reveals that it is the fluid most susceptible to external factors, such as the weather. Contrarily, the remaining refrigerants present a more consistent performance. Finally, the optimization revealed that the R407C refrigerant is the most suitable given that it requires 20% less compression work than the R404A. This provides the heat pump system with a steadier behaviour, a COP ranging from 7 to 8, 30% higher than R410A, a worktime decrease of 1.5 h and heat transfer area of 5.5 flat-plate solar collectors, equivalent to a 31% reduction, both compared to R134a.

Photovoltaic thermal building skin: effect of condensing and evaporating temperature on flow rate and heat transfer

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Ahmad Riaz ◽  
Chao Zhou ◽  
Ruobing Liang ◽  
Jili Zhang
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Mass Flow Rate ◽  
Heat Pump ◽  
Flow Rate ◽  
Pump System ◽  
Content Type ◽  
Heat Pump System ◽  
Double Skin ◽  
Air Channel

Purpose This paper aims to present a numerical study on the natural convection, which operates either as an evaporator or condenser unit of the heat pump system to pre-cool and pre-heat the ambient fresh air. Design/methodology/approach This study focuses on natural air cooling or heating within the air channel considering the double skin configuration. Particular focus is given to the analysis of airflow and the heat transfer processes in an air channel to cool or heat the ambient fresh air. In this study, the physical model consists of one wall, either heated uniformly or cooled uniformly, whereas the other wall is adiabatic. Findings The results show that the variation of both velocity and temperature is observed as the flow transition occurs at the evaporator or condenser wall. In either case, the temperature rises in the range of 6.3–8.4°C with an increase in mass flow rate from 0.07–0.08 kg/s in the photovoltaic thermal condenser part, while in the photovoltaic thermal evaporator part, the change in mass flow rate from 0.048–0.061 kg/s causes a decrease in temperature from 7.1–4.5°C. Practical implications The solar-assisted photovoltaic thermal heat pump system, in building façade having an air layer application, is feasible for pre-heating and pre-cooling the ambient fresh air and also reduces the energy needed to treat the fresh air. Originality/value The influence of condensing and evaporating temperature under natural convection mode in double skin conformation is considered for pre-heating and pre-cooling of ambient fresh air.

Thermoeconomic Analysis on the Performance Characteristics of a Multi-Stage Irreversible Combined Heat Pump System

2000 ◽  
Vol 122 (4) ◽  
pp. 212-216 ◽  
Author(s):  
Jincan Chen ◽  
Chih Wu
Keyword(s):  
Heat Transfer ◽  
Heat Pump ◽  
Heat Exchangers ◽  
Power Input ◽  
Coefficient Of Performance ◽  
Working Fluid ◽  
Pump System ◽  
Heat Pump System ◽  
Maximum Profit ◽  
Multi Stage

A cycle model of a multi-stage combined heat pump system, which includes the irreversibility of finite rate heat transfer across finite temperature differences and the irreversibilities inside the working fluid, is established and used to investigate the influence of these irreversibilities on the performance of the system. The profit of operating the heat pump system is taken as an objective function for optimization. The maximum profit is calculated for a given total heat transfer area or total thermal conductance of heat exchangers. The coefficient of performance, heating load, and power input at the maximum profit are determined. The distribution of the heat transfer areas or the thermal conductances of heat exchangers and the temperature ratios of the working fluids of two adjacent cycles in heat exchange processes are optimized. The results obtained here are generally significant. They are suitable for an arbitrary-stage irreversible and endo- reversible combined heat pump system. [S0195-0738(00)01104-3]

Heat Pump Using a Solar Collector With Photovoltaic Modules on the Surface

1997 ◽  
Vol 119 (2) ◽  
pp. 147-151 ◽  
Author(s):  
Sadasuke Ito ◽  
Nakatsu Miura ◽  
Jin Qi Wang ◽  
Miwako Nishikawa
Keyword(s):  
Electric Power ◽  
Heat Pump ◽  
Convective Heat Transfer Coefficient ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Pump System ◽  
Heat Pump System ◽  
Photovoltaic Modules ◽  
Photovoltaic Array ◽  
Hot Water Supply

It is known that the higher the evaporation temperature, the higher the coefficient of performance of a heat pump for hot water supply. Flat-plate solar collectors which were insulated on the back and bonded with flexible polycrystalline silicon-type photovoltaic modules on the upper surfaces were used in a heat pump system as the evaporator in order to increase the coefficient of performance and to generate electric power. The total area of the collectors was 3.24 m2 and the photovoltaic modules covered 76 percent of the area. The characteristics of the photovoltaic array and the thermal performance of the heat pump were studied experimentally. The results indicated that a coefficient of performance (COP) of the heat pump as high as six could be obtained at 40°C of the water temperature at the inlet of the condenser in the daytime in winter. The peak electric power generated was 120 W. It was found that the photovoltaic modules on the collectors did not influence the performance of the heat pump appreciably. When there was little solar radiation, the COP of the heat pump became two which was very low. This defect was improved by using an evaporator, which had a high convective heat transfer coefficient, arranged in parallel with the fiat-plate collectors.

Simulative Study on Solar-Assisted Air Source Heat Pump System

2013 ◽  
Vol 671-674 ◽  
pp. 2141-2144 ◽  
Author(s):  
Qiang Wang ◽  
Feng Zhen Liu ◽  
Li Jun Hou ◽  
Jian Hua Gao
Keyword(s):  
Heat Pump ◽  
Operating Conditions ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Pump Unit ◽  
Pump System ◽  
Heat Pump System ◽  
Air Source Heat Pump ◽  
Heat Pump Unit ◽  
The Stability

A solar assisted air source heat pump unit is designed. The mathematical model of the unit is established and two hybrid operating conditions of the system are simulated. The simulative studying results shows that in winter the solar assisted air source heat pump unit can make full use of solar energy and the coefficient of performance (COP) of air source heat pump can be improved. In summer the cooling heat of air source heat pump could be recovered to improve the stability of solar hot water collector and the COP of the air source heat pump unit is greatly improved. The performance of solar assisted air source heat pump unit is better than that of with no solar assisted air source heat pump.

DETERMINING THE PROFITABILITY OF GREENHOUSE ELECTROTECHNOLOGIES: A MODELING APPROACH

HortScience ◽  
1994 ◽  
Vol 29 (4) ◽  
pp. 249a-249
Author(s):  
Eric A. Lavoie ◽  
Damien de Halleux ◽  
André Gosselin ◽  
Jean-Claude Dufour
Keyword(s):  
Energy Consumption ◽  
Heat Pump ◽  
Water System ◽  
Heat Pumps ◽  
Hot Water ◽  
Pump System ◽  
Heat Pump System ◽  
Artificial Lighting ◽  
Hot Air ◽  
Marketable Fruit

The main objective of this research was to produce a simulated model that permitted the evaluation of operating costs of commercial greenhouse tomato growers with respect to heating methods (hot air, hot water, radiant and heat pumps) and the use of artificial lighting for 1991 and 1992. This research showed that the main factors that negatively influence profitability were energy consumption during cold periods and the price of tomatoes during the summer season. The conventional hot water system consumed less energy than the heat pump system and produced marketable fruit yields similar to those from the heat pump system. The hot water system was generally more profitable in regards to energy consumption and productivity. Moreover, investment costs were less; therefore, this system gives best overall financial savings. As for radiant and hot air systems, their overall financial status falls between that of the hot water system and the heat pump. The radiant system proved to be more energy efficient that the hot air system, but the latter produced a higher marketable fruit yield over the 2-year study.

scholarly journals Performance testing of a heat pump system with auxiliary hot water under different ambient temperatures

2021 ◽  
Author(s):  
Xuejuan Li ◽  
Yunfeng Wang ◽  
Ming Li ◽  
Mengxiao Hang ◽  
Wenkui Zhao ◽  
...  
Keyword(s):  
Heat Pump ◽  
Performance Testing ◽  
Hot Water ◽  
Pump System ◽  
Heat Pump System ◽  
Ambient Temperatures
Sign in / Sign up

Export Citation Format

Share Document