Two-Phase Flow Induced Force Fluctuations on Pipe Bend

Author(s):  
Shuichiro Miwa ◽  
Yang Liu ◽  
Takashi Hibiki ◽  
Mamoru Ishii ◽  
Yoshiyuki Kondo ◽  
...  

In this study, fluctuating force induced by both upward and horizontal gas-liquid two-phase flow on 90 degree pipe bend at atmospheric condition was investigated. First, the database comprised of dynamic force signals and two-phase flow parameters such as volumetric fluxes, area averaged void fraction and pressure fluctuations covering entire two-phase flow regimes was developed for both flow orientations. Then, study was conducted to develop a model which is capable of predicting the force fluctuation frequency and magnitudes particularly for the slug flow regime. The model was fundamentally developed from the local instantaneous two-fluid model which was applied to the control volume around the elbow test section. Main contribution of the force fluctuation of two-phase flow is from the momentum and pressure fluctuations for most of the flow regimes. For slug flow regime, however, water-hammer like impact was produced by the collision of liquid slug against the structure surface. In order to consider that effect, the liquid slug impact force model was developed. The model utilizes two-group interfacial area concentration correlation to treat the flow regime transition without an abrupt discontinuity. It was found that the newly developed model is capable of predicting two-phase flow induced force fluctuation and dominant frequency range with satisfactory accuracy for flow regimes up to churn-turbulent.

1994 ◽  
Vol 59 (12) ◽  
pp. 2595-2603
Author(s):  
Lothar Ebner ◽  
Marie Fialová

Two regions of instabilities in horizontal two-phase flow were detected. The first was found in the transition from slug to annular flow, the second between stratified and slug flow. The existence of oscillations between the slug and annular flows can explain the differences in the limitation of the slug flow in flow regime maps proposed by different authors. Coexistence of these two regimes is similar to bistable behaviour of some differential equation solutions.


2011 ◽  
Vol 133 (9) ◽  
Author(s):  
Sidharth Paranjape ◽  
Shao-Wen Chen ◽  
Takashi Hibiki ◽  
Mamoru Ishii

Flow regime maps were obtained for adiabatic air-water two-phase flow through a flow channel with 8 × 8 rod bundle, which simulated a typical rod bundle in a boiling water reactor. Impedance void meters were used to measure the area averaged void fraction at various axial locations in the flow channel. The Cumulative Probability Distribution Functions of the signals from the impedance meters were utilized along with self organizing neural network methodology to identify the flow regimes. The flow regimes were identified at five axial locations in the channel in order to understand the development of the flow regimes in axial direction. The experimental flow regime transition boundaries for bubbly to cap-bubbly and part of the cap-turbulent to churn-turbulent agreed with the theoretical boundaries of bubbly to slug and slug to churn-turbulent in round pipes. In addition, the two impedance void meters located across a spacer grid, revealed the nature of change in the flow regime across the spacer grid.


Author(s):  
Darin J. Sharar ◽  
Arthur E. Bergles ◽  
Nicholas R. Jankowski ◽  
Avram Bar-Cohen

A non-intrusive optical method for two-phase flow pattern identification was developed to validate flow regime maps for two-phase adiabatic flow in a small diameter tube. Empirical measurements of film thickness have been shown to provide objective identification of the dominant two-phase flow regimes, representing a significant improvement over the traditional use of exclusively visual and verbal descriptions. Use of this technique has shown the Taitel-Dukler, Ullmann-Brauner, and Wojtan et al. phenomenological flow regime mapping methodologies to be applicable, with varying accuracy, to small diameter two-phase flow.


2016 ◽  
Vol 138 (9) ◽  
Author(s):  
Shuichiro Miwa ◽  
Takashi Hibiki ◽  
Michitsugu Mori

Fluctuating force induced by horizontal gas–liquid two-phase flow on 90 deg pipe bend at atmospheric pressure condition is considered. Analysis was conducted to develop a model which is capable of predicting the peak force fluctuation frequency and magnitudes, particularly at the stratified wavy two-phase flow regime. The proposed model was developed from the local instantaneous two-fluid model, and adopting guided acoustic theory and dynamic properties of one-dimensional (1D) waves to consider the collisional force due to the interaction between dynamic waves and structure. Comparing the developed model with experimental database, it was found that the main contribution of the force fluctuation due to stratified wavy flow is from the momentum and pressure fluctuations, and collisional effects. The collisional effect is due to the fluid–solid interaction of dynamic wave, which is named as the wave collision force. Newly developed model is capable of predicting the force fluctuations and dominant frequency range with satisfactory accuracy for the flow induced vibration (FIV) caused by stratified wavy two-phase flow in 52.5 mm inner diameter (ID) pipe bend.


Author(s):  
Christian Weinmu¨ller ◽  
Dimos Poulikakos

Microfluidics has experienced a significant increase in research activities in recent years with a wide range of applications emerging, such as micro heat exchangers, energy conversion devices, microreactors, lab-on-chip devices and micro total chemical analysis systems (μTAS). Efforts to enhance or extend the performance of single phase microfluidic devices are met by two-phase flow systems [1, 2]. Essential for the design and control of microfluidic systems is the understanding of the fluid/hydrodynamic behavior, especially pressure drop correlations. These are well established for single phase flow, however, analytical correlations for two-phase flow only reflect experimentally obtained values within an accuracy of ± 50% [3, 4]. The present study illustrates the effect of two-phase flow regimes on the pressure drop. Experimental measurement data is put into relation of calculated values based on established correlations of Lockhart-Martinelli with Chisholm modifications for macroscopic flows [5, 6] and Mishima-Hibiki modifications for microscale flows [7]. Further, the experimental pressure drop data is superimposed onto two-phase flow maps to identify apparent correlations of pressure drop abnormalities and flow regimes. The experiments were conducted in a square microchannel with a width of 200 μm. Optical access is guaranteed by an anodically bonded glass plate on a MEMS fabricated silicon chip. Superficial velocities range from 0.01 m/s to 1 m/s for the gas flow and from 0.0001 m/s to 1 m/s for the liquid flow with water as liquid feed and CO2 as gas. The analysis of the flow regimes was performed by imaging the distinct flow regimes by laser induced fluorescence microscopy, employing Rhodamine B as the photosensitive dye. The pressure drop was synchronically recorded with a 200 mbar, 2.5 bar and 25 bar differential pressure transmitter and the data was exported via a LabView based software environment, see Figure 1. Figure 2 illustrates the experimentally obtained pressure drop in comparison to the calculated values based on the Lockhard-Martinelli correlation with the Chisholm modification and the Mishima-Hibiki modification. For both cases the predications underestimate the two-phase pressure drop by more than 50%. Nevertheless, the regression of the experimental data has an offset of linear nature. Two-phase flow is assigned to flow regime maps of bubbly, wedging, slug or annular flow defined by superficial gas and liquid velocities. In Figure 3 the pressure drop is plotted as a surface over the corresponding flow regime map. Transition lines indicate a change of flow regimes enclosing an area of an anticline in the pressure data. In the direct comparison between the calculated and the measured values, the two surfaces show a distinct deviation. Especially, the anticline of the experimental data is not explained by the analytical correlations. Figure 4 depicts the findings of Figure 3 at a constant superficial velocity of 0.0232 m/s. The dominant influence of the flow regimes on the pressure drop becomes apparent, especially in the wedging flow regime. The evident deviation of two-phase flow correlations for the pressure drop is based on omitting the influence of the flow regimes. In conclusion, the study reveals a strong divergence of pressure drop measurements in microscale two-phase flow from established correlations of Lockhart-Martinelli and recognized modifications. In reference to [8, 9], an analytical model incorporating the flow regimes and, hence, predicting the precise pressure drop would be of great benefit for hydrodynamic considerations in microfluidics.


2000 ◽  
Author(s):  
Bofeng Bai ◽  
Tiejun Wu ◽  
Liejin Guo ◽  
Xuejun Chen

Abstract The fluctuating pressure drop for air-water two-phase flow was measured in the vertical upward section of U-type tube with 0.05m I.D. The feature of the fluctuations was extracted by means of statistical and chaotic theories. The influence of liquid superficial velocity on the features was also investigated. The results showed that the mean, root mean square, fractal dimension of pressure drop fluctuations is function of flow regimes. The fractal dimension can be larger than 1.5 in annular flow with great liquid superficial velocity which is reported for the first time. Furthermore, the present paper provided a feasible solution, which the gas-liquid two-phase flow regimes can be recognized automatically and objectively on basis of the combination of the Counter Propagation Network (CPN) and the FFT coefficients of the differential pressure fluctuations. The recognition possibility is determined by the clustering results of the Kohonen layer in the CPN. With the presented test cases, the possibility can be greater than 90 percent for different liquid phase velocity.


Author(s):  
Stamatis Kalogerakos ◽  
Mustapha Gourma ◽  
Chris Thompson

Severe limitations of the use of three-dimensional computational fluid dynamics codes (CFD) arise when trying to simulate multiphase flow in long pipes due to time constraints. 1D codes for two-phase flow, based on two-fluid models, are fast but are known to be accurate only when the velocities are within the Kelvin-Helmholtz inviscid limit [1]. An alternative is to carry out a two-dimensional CFD simulation of a channel based on the Volume of Fluid (VOF) model. 2D CFD has a wider applicability range compared to 1D, it does not have the issue of ill-posedness and it also has better turbulence models built in. Again compared to 1D the 2D VOF model has a better interface description and wall treatment. In this paper a novel method is introduced that allows swift simulations of pipeline two-phase flow in the stratified and slug flow regime, by approximating the pipe as a channel and with a methodology that solves the problem of the interfacial velocity differences, inherent in the volume of fluid model. An initial validation using the wave growth problem has already been carried out [2]. Here a set consisting of 92 experimental cases in the slug flow regime has been simulated with 2D CFD, and the simulation results showed a good agreement with experimental results. Discussions in the paper include also the question of the range of applicability for 2D CFD, and the advantages and disadvantages compared to 3D CFD and also to 1D code based on the two-fluid model. Shear stresses are then extracted from the 2D CFD simulations and used to recalibrate the friction factors [3] used in the 1D code.


Author(s):  
Zhaoxu Li ◽  
Hongye Zhu

Two-phase flow in helically coiled tubes is becoming the interest of many investigators because of its importance in various applications, such as nuclear engineering, chemical engineering, refrigerating engineering and power engineering. Compared with U-type tubes used in pressurized water reactor (PWR), helically coiled tubes have advantages in size, heat transfer capacity, thermal stress toleration and two-phase stability. Accordingly the helically coiled tubes have been utilized in the steam generators of the next general reactors, such as gas-cooled reactor, fast breeder reactor and integrated pressurized water reactor. In helically coiled tubes the characteristics of momentum and heat transfer are distinct from those in straight tubes due to the presence of centrifugal force, especially for two-phase flow. Meanwhile, the transitions of flow regime, which is the crucial knowledge for the designers to determine the heat transfer rates and flow resistance, are also significantly affected by the centrifugal force. In this study, two-phase flow regimes in helically coiled tubes are investigated. Computational fluid dynamics (CFD), using fractional volume of fluid (VOF) model, is carried out to simulate wavy and slug flow regimes in helically coiled tubes. The corresponding experiment is also conducted to visualize these flow regimes at different superficial flow velocities. Numerical simulation results actually reflect the influence of centrifugal force on the two-phase flow and show a good agreement with the photographs captured from the experiment. Based on the simulations at different superficial flow velocities, the boundary between the slug and wavy flow regimes is predicted, in addition, compared with that in inclined tubes. The comparison indicates that centrifugal force could induce the appearance of wavy flows in advance and prompt the transition from slug flow to wavy flow.


Sign in / Sign up

Export Citation Format

Share Document