Effect of Stiff Coatings on EHL Film Thickness in Point Contacts

2007 ◽  
Author(s):  
Yuchuan Liu ◽  
Q. Jane Wang ◽  
Dong Zhu
Keyword(s):  
Film Thickness ◽  
Working Conditions ◽  
Coating Thickness ◽  
Point Contact ◽  
Thickness Variation ◽  
Point Contacts ◽  
Lubricant Film Thickness ◽  
Wide Range ◽  
Minimum Film Thickness ◽  
Coating Material Properties

This study investigates the influences of coating material properties and coating thickness on lubricant film thickness based on a point-contact isothermal EHL model developed recently by the authors. The results present the trend of minimum film thickness variation as a function of coating thickness and elastic modulus under a wide range of working conditions. Numerical results indicates that the increase in minimum film thickness, Imax, and the corresponding optimal dimensionless coating thickness, H2, can be expressed in the following formulas: Imax=0.766M0.0248R20.0296L0.1379exp(−0.0245ln2L)H2=0.049M0.4557R2−0.1722L0.7611exp(−0.0504ln2M−0.0921ln2L) These formulas can be used to estimate the effect of a coating on EHL film thickness.

Effect of Stiff Coatings on EHL Film Thickness in Point Contacts

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Yuchuan Liu ◽  
Q. Jane Wang ◽  
Dong Zhu
Keyword(s):  
Film Thickness ◽  
Coating Thickness ◽  
Performance Enhancement ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Thickness Variation ◽  
Grand Challenge ◽  
Maximum Increase ◽  
Wide Range ◽  
Minimum Film Thickness

Coatings are widely used for interface performance enhancement and component life improvement, as well as for corrosion prevention and surface decoration. More and more mechanical components, especially those working under severe conditions, are coated with stiff (hard) thin coatings. However, the effects of coatings on lubrication characteristics, such as film thickness and friction, have not been well understood, and designing coating for optimal tribological performance is a grand challenge. In this paper, the influences of coating material properties and coating thickness on lubricant film thickness are investigated based on a point-contact isothermal elastohydrodynamic lubrication (EHL) model developed recently by the authors. The results present the trend of minimum film thickness variation as a function of coating thickness and elastic modulus under a wide range of working conditions. Curve fitting of numerical results indicates that the maximum increase in minimum film thickness, Imax, and the corresponding optimal dimensionless coating thickness, H2max, can be expressed in the following forms: Imax=0.769M0.0238R20.0297L0.1376exp(−0.0243ln2L) and H2max=0.049M0.4557R2−0.1722L0.7611exp(−0.0504ln2M−0.0921ln2L). These formulas can be used to estimate the effect of coatings on film thickness for EHL applications.

An Experimental Evaluation of the Hamrock and Dowson Minimum Film Thickness Equation for Fully Flooded EHD Point Contacts

1981 ◽  
Vol 103 (2) ◽  
pp. 284-294 ◽  
Author(s):  
K. A. Koye ◽  
W. O. Winer
Keyword(s):  
Experimental Data ◽  
Statistical Analysis ◽  
Film Thickness ◽  
Experimental Evaluation ◽  
Point Contact ◽  
Major Axis ◽  
Point Contacts ◽  
Lubricant Film Thickness ◽  
Minimum Film Thickness ◽  
Ellipticity Ratio

Fifty-seven measurements of the minimum lubricant film thickness separating the elastohydrodynamically lubricated point contact of a steel crowned roller and a flat sapphire disk were made by an optical interferometry technique. The data collected were used to evaluate the Hamrock and Dowson minimum EHD film thickness model over a practical range of contact ellipticity ratio where the major axis of the contact ellipse is aligned both parallel and perpendicular to the direction of motion. A statistical analysis of the measured film thickness data showed that the experimental data averaged 30 percent greater film thickness than the Hamrock and Dowson model predicts.

The Elastohydrodynamic Lubrication of Elliptical Point Contacts Operating in the Isoviscous Region

1995 ◽  
Vol 209 (4) ◽  
pp. 225-234 ◽  
Author(s):  
C J Hooke
Keyword(s):  
Film Thickness ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Radius Ratio ◽  
Point Contacts ◽  
Reasonable Estimate ◽  
Wide Range ◽  
Minimum Film Thickness

The elastohydrodynamic lubrication of point contacts is examined and results for the minimum film thickness are presented for a wide range of radius ratios and operating conditions. The results are compared with the predictions of the appropriate regime formulae. Although these formulae give a reasonable estimate of the contact's behaviour, the actual clearances are often substantially different, particularly close to the regime boundaries. Interpolation equations for seven values of radius ratio are given and these should be sufficient to allow the minimum clearance to be estimated for most isoviscous point contacts.

scholarly journals Analysis of Starvation Effects on Hydrodynamic Lubrication in Nonconforming Contacts

1982 ◽  
Vol 104 (3) ◽  
pp. 410-417 ◽  
Author(s):  
D. E. Brewe ◽  
B. J. Hamrock
Keyword(s):  
Film Thickness ◽  
Hydrodynamic Lubrication ◽  
Three Dimensional ◽  
Point Contact ◽  
Sharp Decrease ◽  
Reduction Factor ◽  
Wide Range ◽  
Minimum Film Thickness ◽  
Contour Plots ◽  
Starvation Effects

Numerical methods were used to determine the effects of lubricant starvation on the minimum film thickness under conditions of a hydrodynamic point contact. Starvation was effected by varying the fluid inlet level. The Reynolds boundary conditions were applied at the cavitation boundary and zero pressure was stipulated at the meniscus or inlet boundary. The analysis is considered valid for a range of speeds and loads for which thermal, piezoviscous, and deformation effects are negligible. It is applied to a wide range of geometries (i.e., from a ball-on-plate configuration to a ball in a conforming groove). Seventy-four cases were used to numerically determine a minimum-film-thickness equation as a function of the ratio of dimensionless load to dimensionless speed for varying degrees of starvation. From this, a film reduction factor was determined as a function of the fluid inlet level. Further, a starved fully flooded boundary was defined and an expression determining the onset of starvation was derived. As the degree of starvation was increased, the minimum film thickness decreased gradually until the fluid inlet level became critical. Reducing the fluid inlet level still further led to a sharp decrease in the minimum film thickness. An expression determining the critically starved fluid inlet level was derived. The changes in the inlet pressure buildup due to changing the available lubricant supply are presented in the form of three-dimensional isometric plots and also in the form of contour plots.

Numerical Solution of Mixed Thermal Elastohydrodynamic Lubrication in Point Contacts With Three-Dimensional Surface Roughness

2016 ◽  
Vol 139 (1) ◽  
Author(s):  
Xiaopeng Wang ◽  
Yuchuan Liu ◽  
Dong Zhu
Keyword(s):  
Surface Roughness ◽  
Film Thickness ◽  
Three Dimensional ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Lubricant Film ◽  
Operating Conditions ◽  
Thickness Variation ◽  
Wide Range ◽  
Film Lubrication

Elastohydrodynamic lubrication (EHL) is a common mode of fluid-film lubrication in which many machine elements operate. Its thermal behavior is an important concern especially for components working under extreme conditions such as high speeds, heavy loads, and surfaces with significant roughness. Previous thermal EHL (TEHL) studies focused only on the cases with smooth surfaces under the full-film lubrication condition. The present study intends to develop a more realistic unified TEHL model for point contact problems that is capable of simulating the entire transition of lubrication status from the full-film and mixed lubrication all the way down to boundary lubrication with real machined roughness. The model consists of the generalized Reynolds equation, elasticity equation, film thickness equation, and those for lubricant rheology in combination with the energy equation for the lubricant film and the surface temperature equations. The solution algorithms based on the improved semi-system approach have demonstrated a good ability to achieve stable solutions with fast convergence under severe operating conditions. Lubricant film thickness variation and temperature rises in the lubricant film and on the surfaces during the entire transition have been investigated. It appears that this model can be used to predict mixed TEHL characteristics in a wide range of operating conditions with or without three-dimensional (3D) surface roughness involved. Therefore, it can be employed as a useful tool in engineering analyses.

Temperature Measurements in Sliding Elastohydrodynamic Point Contacts

1974 ◽  
Vol 96 (3) ◽  
pp. 464-469 ◽  
Author(s):  
V. Turchina ◽  
D. M. Sanborn ◽  
W. O. Winer
Keyword(s):  
Film Thickness ◽  
Surface Temperature ◽  
Infrared Radiation ◽  
Point Contact ◽  
Mineral Oil ◽  
Temperature Measurements ◽  
Point Contacts ◽  
Oil Film ◽  
Temperature Distributions ◽  
Minimum Film Thickness

Techniques using the infrared radiation emitted by a sliding EHD point contact to measure oil film and surface temperature are discussed. Temperature distributions in the EHD contact are presented for a naphthenic mineral oil at 1.04 × 109 N/m2 (150,000 psi) Hertz pressure and several sliding velocities. Film temperatures as high as 360 C are reported at locations near the points of minimum film thickness in the contact side lobes.

Non-Newtonian Elastohydrodynamic Lubrication of Point Contact

1991 ◽  
Vol 113 (4) ◽  
pp. 703-711 ◽  
Author(s):  
Kyung Hoon Kim ◽  
Farshid Sadeghi
Keyword(s):  
Film Thickness ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Two Dimensional ◽  
Point Contacts ◽  
Dimensionless Velocity ◽  
Simultaneous System ◽  
Elasticity Equations ◽  
Minimum Film Thickness ◽  
Pressure Spike

A numerical solution to the problem of isothermal non-Newtonian elastohydrodynamic lubrication of rolling/sliding point contacts has been obtained. The multigrid technique is used to solve the simultaneous system of two-dimensional modified Reynolds and elasticity equations. The effects of various loads, speeds, and slide to roll ratios on the pressure distribution, film thickness, and friction force have been investigated. Results for the dimensionless load W = 4.6 × 10−6 and 1.1 × 10−6, and the dimensionless velocity U = 3 × 10−10 and 3 × 10−11 are presented. The results indicate that slide to roll ratio has negligible effect on the minimum film thickness, however, it significantly reduces the pressure spike.

Multigrid, an Alternative Method of Solution for Two-Dimensional Elastohydrodynamically Lubricated Point Contact Calculations

1987 ◽  
Vol 109 (3) ◽  
pp. 437-443 ◽  
Author(s):  
A. A. Lubrecht ◽  
W. E. ten Napel ◽  
R. Bosma
Keyword(s):  
Film Thickness ◽  
Iterative Methods ◽  
Multigrid Method ◽  
Computing Time ◽  
Point Contact ◽  
Two Dimensional ◽  
Point Contacts ◽  
Pressure Profiles ◽  
Minimum Film Thickness ◽  
Method Of Solution

Detailed and accurate film thickness and pressure profiles have been calculated for point contacts at moderate and high loads, using a multigrid method. The influence of the compressibility of the lubricant and of the number of nodal points on the calculated minimum film thickness and maximum spike pressure have been examined. The required computing time is two orders of magnitude less, compared with the calculations using “classical” iterative methods.

scholarly journals A thermal resistances-based approach for thermal-elastohydrodynamic calculations in point contacts

2017 ◽  
Vol 232 (11) ◽  
pp. 2088-2102 ◽  
Author(s):  
Eduardo de la Guerra Ochoa ◽  
Javier Echávarri Otero ◽  
Enrique Chacón Tanarro ◽  
Benito del Río López
Keyword(s):  
Friction Coefficient ◽  
Film Thickness ◽  
Thermal Effects ◽  
Good Accuracy ◽  
Computational Cost ◽  
Point Contact ◽  
Elastohydrodynamic Lubrication ◽  
Point Contacts ◽  
New Approach ◽  
Ball On Disc

This article presents a thermal resistances-based approach for solving the thermal-elastohydrodynamic lubrication problem in point contact, taking the lubricant rheology into account. The friction coefficient in the contact is estimated, along with the distribution of both film thickness and temperature. A commercial tribometer is used in order to measure the friction coefficient at a ball-on-disc point contact lubricated with a polyalphaolefin base. These data and other experimental results available in the bibliography are compared to those obtained by using the proposed methodology, and thermal effects are analysed. The new approach shows good accuracy for predicting the friction coefficient and requires less computational cost than full thermal-elastohydrodynamic simulations.

scholarly journals Analytical Formula for the Ratio of Central to Minimum Film Thickness in a Circular EHL Contact

Lubricants ◽  
2018 ◽  
Vol 6 (3) ◽  
pp. 80 ◽  
Author(s):  
Petr Sperka ◽  
Ivan Krupka ◽  
Martin Hartl
Keyword(s):  
Experimental Data ◽  
Film Thickness ◽  
Analytical Formula ◽  
Numerical Calculations ◽  
Constant Ratio ◽  
Viscosity Coefficients ◽  
Wide Range ◽  
Minimum Film Thickness ◽  
Film Parameter ◽  
Ehl Contact

Prediction of minimum film thickness is often used in practice for calculation of film parameter to design machine operation in full film regime. It was reported several times that majority of prediction formulas cannot match experimental data in terms of minimum film thickness. These standard prediction formulas give almost constant ratio between central and minimum film thickness while numerical calculations show ratio which spans from 1 to more than 3 depending on M and L parameters. In this paper, an analytical formula of this ratio is presented for lubricants with various pressure–viscosity coefficients. The analytical formula is compared with optical interferometry measurements and differences are discussed. It allows better prediction, compared to standard formulas, of minimum film thickness for wide range of M and L parameters.

Sign in / Sign up

Export Citation Format

Share Document