Particle Dispersion and Deposition in a Curved Duct

2009 ◽  
Author(s):  
C. M. Winkler ◽  
S. P. Vanka
Keyword(s):  
Particle Deposition ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Outer Wall ◽  
Particle Dispersion ◽  
Radius Of Curvature ◽  
Dean Number ◽  
Particle Volume ◽  
Particle Tracking Method ◽  
Dean Vortex

Particle transport in ducts of square cross-section with constant streamwise curvature is studied using numerical simulations. The flow is laminar, with Reynolds numbers of Reτ = 40 and 67, based on the friction velocity and duct width. The corresponding Dean numbers for these cases are 82.45 and 184.5, respectively, where De = Rea/R, a is the duct width and R is the radius of curvature. A Lagrangian particle tracking method is used to account for the particle trajectories, with the particle volume fraction assumed to be low such that inter-particle collisions and two-way coupling effects are negligible. Four particle sizes are studied, τp+ = 0.01, 0.05, 0.1, and 1. Particle dispersion patterns are shown for each Dean number, and the steady-state particle locations are found to be reflective of the Dean vortex structure. Particle deposition on the walls is shown to be dependent upon both the Dean number and particle response time, with the four-cell Dean vortex pattern able to prevent particle deposition along the center of the outer wall.

scholarly journals Numerical analysis of heat transfer enhancement with the use of γ-Al2O3/water nanofluid and longitudinal ribs in a curved duct

2012 ◽  
Vol 16 (2) ◽  
pp. 469-480 ◽  
Author(s):  
Hosseinali Soltanipour ◽  
Parisa Choupani ◽  
Iraj Mirzaee
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Base Fluid ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Transfer Enhancement ◽  
Dean Number ◽  
Particle Volume ◽  
The Heat Transfer Coefficient

This paper presents a numerical investigation of heat transfer augmentation using internal longitudinal ribs and ?-Al2O3/ water nanofluid in a stationary curved square duct. The flow is assumed 3D, steady, laminar, and incompressible with constant properties. Computations have been done by solving Navier-Stokes and energy equations utilizing finite volume method. Water has been selected as the base fluid and thermo- physical properties of ?- Al2o3/ water nanofluid have been calculated using available correlations in the literature. The effects of Dean number, rib size and particle volume fraction on the heat transfer coefficient and pressure drop have been examined. Results show that nanoparticles can increase the heat transfer coefficient considerably. For any fixed Dean number, relative heat transfer rate (The ratio of the heat transfer coefficient in case the of ?- Al2o3/ water nanofluid to the base fluid) increases as the particle volume fraction increases; however, the addition of nanoparticle to the base fluid is more useful for low Dean numbers. In the case of water flow, results indicate that the ratio of heat transfer rate of ribbed duct to smooth duct is nearly independent of Dean number. Noticeable heat transfer enhancement, compared to water flow in smooth duct, can be achieved when ?-Al2O3/ water nanofluid is used as the working fluid in ribbed duct.

Development and Validation of Two-Way Fluid-Particle Coupling in Turbulent Flows for a CFD Code

2013 ◽  
Author(s):  
Jianjun Xiao ◽  
Anatoly Svishchev ◽  
Thomas Jordan
Keyword(s):  
Experimental Data ◽  
Turbulent Flows ◽  
Gas Flow ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Continuous Phase ◽  
Particle Dispersion ◽  
Solid Particles ◽  
Particle Volume ◽  
Discrete Phase

A Lagrangian approach was used in CFD code GASFLOW to describe particle dispersion in turbulent flows. One-way coupling between fluid and particle is often used due to its simplicity of implementation. However, in case of higher particle volume fraction or mass loading in the continuous phase, one-way coupling is not sufficient to simulate the interaction between fluid and particles. For instance, the liquid droplets released by a spray nozzle in the nuclear power plant will lead to a strong gas entrainment, and consequently impact the gas flow field. When the volume fraction of the discrete phase is not negligible compared to the continuous phase, the interaction between the continuous fluid and dispersed phase becomes significant. Two-way momentum coupling between fluid and solid particles was developed in CFD code GASFLOW. The dynamics of the discrete particles was solved by an implicit algorithm to ensure the numerical stability. The contribution of all particles to a fluid cell was treated as the source term to the continuous phase which was solved with Arbitrary-Lagrangian-Eulerian (ALE) methodology. In order to verify and validate the code, the calculation results were then compared to theoretical results, predictions of other CFD codes and experimental data. Predictions compared favorably with the experimental data. It indicates that the effect of two-way coupling is significant when the volume fraction of discrete phase is not negligible. Two-way coupling of mass, energy and turbulence will be implemented in the future development of the GASFLOW code.

The Effect of Inlet Conditions on Particle Deposition in Axial Flow Compressor

2014 ◽  
Vol 915-916 ◽  
pp. 1066-1069
Author(s):  
Hong Xu ◽  
Hua Dong Yang ◽  
Guang Ru Hua
Keyword(s):  
Particle Deposition ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Axial Flow ◽  
Particle Mass ◽  
Inlet Temperature ◽  
Particle Volume ◽  
Axial Flow Compressor ◽  
Inlet Conditions ◽  
Flow Compressor

Axial flow compressor is an important component, so the compressor performance is of crucial. Fouling changes blade geometry and blade surface roughness is increased, thus aerodynamic performance is affected. The flow of gas phase and gas-solid coupling phase are implemented to reveal the effect of inlet condition on particle deposition. Based on Euler-Lagrange model, this paper made numerical simulation of gas-solid two phase flow in the axial flow compressor rotor cascade. Simulation result shows that the increase of inlet temperature can result in the reduction of particle volume fraction. And particle mass concentration is affected by particle mass flow rate.

scholarly journals Performance improvement of double-tube gas cooler in CO2 refrigeration system using nanofluids

2015 ◽  
Vol 19 (1) ◽  
pp. 109-118 ◽  
Author(s):  
Jahar Sarkar
Keyword(s):  
Performance Improvement ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Cooling Capacity ◽  
Inlet Temperature ◽  
Refrigeration Cycle ◽  
Particle Volume ◽  
Transcritical Carbon Dioxide ◽  
The Given ◽  
Theoretical Analyses

The theoretical analyses of the double-tube gas cooler in transcritical carbon dioxide refrigeration cycle have been performed to study the performance improvement of gas cooler as well as CO2 cycle using Al2O3, TiO2, CuO and Cu nanofluids as coolants. Effects of various operating parameters (nanofluid inlet temperature and mass flow rate, CO2 pressure and particle volume fraction) are studied as well. Use of nanofluid as coolant in double-tube gas cooler of CO2 cycle improves the gas cooler effectiveness, cooling capacity and COP without penalty of pumping power. The CO2 cycle yields best performance using Al2O3-H2O as a coolant in double-tube gas cooler followed by TiO2-H2O, CuO-H2O and Cu-H2O. The maximum cooling COP improvement of transcritical CO2 cycle for Al2O3-H2O is 25.4%, whereas that for TiO2-H2O is 23.8%, for CuO-H2O is 20.2% and for Cu-H2O is 16.2% for the given ranges of study. Study shows that the nanofluid may effectively use as coolant in double-tube gas cooler to improve the performance of transcritical CO2 refrigeration cycle.

A simulation and experimental study on particle volume fraction of PMMA suspension in centrifugal fields

2021 ◽  
Author(s):  
Yosephus Ardean Kurnianto Prayitno ◽  
Tong Zhao ◽  
Yoshiyuki Iso ◽  
Masahiro Takei
Keyword(s):  
Experimental Study ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Particle Volume

Solidification Processing of Functionally Graded Materials by Sedimentation

1999 ◽  
Author(s):  
J. W. Gao ◽  
S. J. White ◽  
C. Y. Wang
Keyword(s):  
Functionally Graded Materials ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Computer Code ◽  
Functionally Graded ◽  
Particle Volume ◽  
Particle Sedimentation ◽  
Graded Materials ◽  
Free Zone ◽  
Free Region

Abstract A combined experimental and numerical investigation of the solidification process during gravity casting of functionally graded materials (FGMs) is conducted. Focus is placed on the interplay between the freezing front propagation and particle sedimentation. Experiments were performed in a rectangular ingot using pure substances as the matrix and glass beads as the particle phase. The time evolutions of local particle volume fractions were measured by bifurcated fiber optical probes working in the reflection mode. The effects of various processing parameters were explored. It is found that there exists a particle-free zone in the top portion of the solidified ingot, followed by a graded particle distribution region towards the bottom. Higher superheat results in slower solidification and hence a thicker particle-free zone and a higher particle concentration near the bottom. The higher initial particle volume fraction leads to a thinner particle-free region. Lower cooling temperatures suppress particle settling. A one-dimensional solidification model was also developed, and the model equations were solved numerically using a fixed-grid, finite-volume method. The model was then validated against the experimental results, and the validated computer code was used as a tool for efficient computational prototyping of an Al/SiC FGM.

Shock-Induced Multiphase Instability in a High Volume Fraction Finite-Thickness Particle Layer

2021 ◽  
Author(s):  
Bertrand Rollin ◽  
Frederick Ouellet ◽  
Bradford Durant ◽  
Rahul Babu Koneru ◽  
S. Balachandar
Keyword(s):  
Shock Tube ◽  
Volume Fraction ◽  
Solid Phase ◽  
Particle Volume Fraction ◽  
Finite Thickness ◽  
Spherical Particles ◽  
Shock Strength ◽  
Particle Volume ◽  
Particle Cloud ◽  
Particle Layer

Abstract We study the interaction of a planar air shock with a perturbed, monodispersed, particle curtain using point-particle simulations. In this Eulerian-Lagrangian approach, equations of motion are solved to track the position, momentum, and energy of the computational particles while the carrier fluid flow is computed in the Eulerian frame of reference. In contrast with many Shock-Driven Multiphase Instability (SDMI) studies, we investigate a configuration with an initially high particle volume fraction, which produces a strongly two-way coupled flow in the early moments following the shock-solid phase interaction. In the present study, the curtain is about 4 mm in thickness and has a peak volume fraction of about 26%. It is composed of spherical particles of d = 115μm in diameter and a density of 2500 kg.m−3, thus replicating glass particles commonly used in multiphase shock tube experiments or multiphase explosive experiments. We characterize both the evolution of the perturbed particle curtain and the gas initially trapped inside the particle curtain in our planar three-dimensional numerical shock tube. Control parameters such as the shock strength, the particle curtain perturbation wavelength and particle volume fraction peak-to-trough amplitude are varied to quantify their influence on the evolution of the particle cloud and the initially trapped gas. We also analyze the vortical motion in the flow field. Our results indicate that the shock strength is the primary contributor to the cloud particle width. Also, a classic Richtmyer-Meshkov instability mixes the gas initially trapped in the particle curtain and the surrounding gas. Finally, we observe that the particle cloud contribute to the formation of longitudinal vortices in the downstream flow.

Sign in / Sign up

Export Citation Format

Share Document