Dynamic Analysis of a Dual-Mode CO2 Heat Pump With Both Hot and Cold Thermal Storage

2013 ◽  
Author(s):  
Lars Houbak-Jensen ◽  
Anders Holten ◽  
Morten Boje Blarke ◽  
Eckhard A. Groll ◽  
Ali Shakouri ◽  
...  
Keyword(s):  
Differential Equations ◽  
Heat Pump ◽  
Cold Storage ◽  
Coefficient Of Performance ◽  
Computational Time ◽  
Extended Model ◽  
Algebraic Differential Equation ◽  
Spatial Discretization ◽  
Pump System ◽  
Heating And Cooling

We investigated the dynamics of a transcritical CO2 heat pump system including hot and cold thermal storages, which makes up the concept “thermal battery”. The analytical model is used for the study of the dynamics of the system involving simultaneous supply of heating and cooling for buildings. The model includes the dynamics of the gas cooler, evaporator and the thermal storages, while the compressor and the expansion valve are considered quasi-static. The heat transfer in the dynamically modeled components is described by partial differential equations (PDEs) consisting of heat conduction, convection, and source terms. Each component is divided into a number of volumes adjusted according to the required precision and reasonable computational time. We applied two discretization schemes in order to find a numerical solution to the PDEs. The spatial discretization for the heat exchangers is performed by using the upwind scheme, where the fluid properties are individually calculated within each volume. Due to the discrete events in form of tapping and loading (or charging and discharging) of the heat storages, the discretization approach takes into account the sharp spatial transitions within the thermal storages. Therefore, the method of lines in combination with the Superbee slope-limiter was applied for the spatial discretization for high resolution calculation. The modeling approach results in a set of algebraic and ordinary differential equations (ODEs), hence the model becomes an algebraic differential equation problem, which we solved by using MATLAB solver ODE15s. This extended model was used to simulate a dynamic response of the case with varying heating and cooling consumption over a period of 24 hours in a building. The heating and cooling energy consumption follow a sinusoidal and continuous pattern. The results include the effect on both the outlet temperatures and the system coefficient-of-performance (COP). The outlet energy from the hot storage and the cold storage is used for heating tap water and a chilled water space cooling application subject to temperature requirements. Dimensioning of both storages is crucial for obtaining the required temperatures. The model identifies the critical storage levels required to satisfy the periodic but out-of-phase combination of heating and cooling demands. The volume of the cold storage will have to be considerably larger than the hot storage due to the lower temperature difference.

Experimental Study of Heating-Cooling Combined Ground Source Heat Pump System with Horizontal Ground Heat Exchanger

2011 ◽  
Vol 374-377 ◽  
pp. 398-404 ◽  
Author(s):  
Ying Ning Hu ◽  
Ban Jun Peng ◽  
Shan Shan Hu ◽  
Jun Lin
Keyword(s):  
Heat Exchanger ◽  
Heat Exchange ◽  
Heat Pump ◽  
Hot Water ◽  
Coefficient Of Performance ◽  
Ground Heat Exchanger ◽  
Pipe Length ◽  
Pump System ◽  
Heat Pump System ◽  
Heating And Cooling

A hot-water and air-conditioning (HWAC) combined ground sourse heat pump(GSHP) system with horizontal ground heat exchanger self-designed and actualized was presented in this paper. The heat transfer performance for the heat exchanger of two different pipe arrangements, three layers and four layers, respectively, was compared. It showed that the heat exchange quantity per pipe length for the pipe arrangement of three layers and four layers are 18.0 W/m and 15.0 W/m. The coefficient of performance (COP) of unit and system could remain 4.8 and 4.2 as GSHP system for heating water, and the COP of heating and cooling combination are up to 8.5 and 7.5, respectively. The power consumption of hot-water in a whole year is 9.0 kwh/t. The economy and feasibility analysis on vertical and horizontal ground heat exchanger were made, which showed that the investment cost per heat exchange quantity of horizontal ground heat exchanger is 51.4% lower than that of the vertical ground heat exchanger, but the occupied area of the former is 7 times larger than the latter's.

SIMULATION ON OPERATION CHARACTERISTICS OF HYBRID GROUND-AIR SOURCE HEAT PUMP SYSTEM WITH NATURAL COLD STORAGE

2014 ◽  
Vol 22 (02) ◽  
pp. 1440004 ◽  
Author(s):  
Z. W. HAN ◽  
X. MENG ◽  
M. LIN ◽  
Y. H. ZHANG ◽  
J. YANG ◽  
...  
Keyword(s):  
Heat Pump ◽  
Cold Storage ◽  
Coefficient Of Performance ◽  
Pump System ◽  
Heat Pump System ◽  
Air Source Heat Pump ◽  
Operational Life ◽  
Vapor Compression Refrigeration Cycle ◽  
Set Up ◽  
Operation Characteristics

To solve the problem of the coefficient of performance (COP) decrease and power crunch in cooling dominated South China associated with the long-term usage of ground-source heat pump system (GSHPS), a hybrid ground-air source heat pump system (HGASHPS) with natural cold storage is presented in this paper. The system consists of a GSHP system and compound air-cooled chillers (CACC), which can be operated according to the vapor compression refrigeration cycle or separate type heat pipe natural cycle. The mathematical models of each part of the system were set up and the conversion conditions between operation modes for the system were determined. The transient simulation for HGASHPS with natural cold storage in Nanjing was carried out. The operation characteristics of the systems in operational life were comparatively analyzed. The simulation results indicated that the HGASHPS with natural cold storage could retain the thermal balance of soil temperature field in one year cycle and increase the COP and reliability of the system.

The Performance Improvements of a Ground-Coupled Heat Pump System for both Building Heating and Cooling Modes

2011 ◽  
Vol 354-355 ◽  
pp. 807-810 ◽  
Author(s):  
Zi Shu Qi ◽  
Qing Gao ◽  
Yan Liu ◽  
Y.Y. Yan ◽  
Jeffrey D. Spitler
Keyword(s):  
Heat Pump ◽  
Temperature Response ◽  
Energy Performance ◽  
Coefficient Of Performance ◽  
Fluid Temperature ◽  
Time Step ◽  
Pump System ◽  
Heating And Cooling ◽  
Ground Coupled Heat Pump ◽  
Cooling Loads

The objective of the paper is to describe the performance of ground-coupled heat pump (GCHP) system in 20 years. A mathematical model for simulation of GCHP system is built based on long time-step Eskilson’s theory. The design methodology is based on a simulation that predicts the temperature response of the ground heat exchanger (GHE) to monthly heating and cooling loads and monthly peak heating and cooling demands over a number of years. The temperature response also has a secondary impact on the predicted energy consumption of the system, as the coefficient of performance (COP) of the heat pump varies with entering fluid temperature. This paper presents GCHP system can achieve better energy performance in building that heating and cooling loads are balanced all the year round. It is illustrated by performing a GHE for a 300 m2 building located in Changchun, China.

The Comparison of Experiment Results and CFD Simulation in the Heat Pump System Using Thermobank and Two-Phase Ejector for Heating Room and Cold Storage

2016 ◽  
Vol 24 (01) ◽  
pp. 1650004 ◽  
Author(s):  
Le Ngoc Cuong ◽  
Jong-Taek Oh
Keyword(s):  
Heat Pump ◽  
Cold Storage ◽  
Cfd Simulation ◽  
Waste Heat ◽  
Coefficient Of Performance ◽  
Two Phase ◽  
Pump System ◽  
Heat Pump System ◽  
Dimension Formula ◽  
Floor Panel

In this paper, the heat pump system has been developed by CFD simulation and experimental investigation. It studies the thermal behavior of a thermobank and COP on heat pump system and cold storage. The thermobank stores the waste heat of during refrigeration cycles and this energy is used for defrosting process and heating room. It also reduces defrosting time and condensation load so that the temperature regulation in the cold storage is constant. The system is investigated experimentally and CFD simulated under thermobank. The dimension [Formula: see text] of cold storage is [Formula: see text][Formula: see text]m, thermobank is [Formula: see text][Formula: see text]mm. The temperature of ambient on CFD simulation process is 20[Formula: see text]C. This heat pump system can be used to keep preservation of agricultural products in cold storage warehouse together with floor panel heating for room in winter. The ejector is used in system with the aim of increasing coefficient of performance (COP) and decrease in compressor displacement. As the experimental results, its COP is increased about 38.57% when using thermobank and ejector in heat pump system.

Development of Heat Pump System Using Thermobank and Ejector for Heating Room and Cold Storage

2015 ◽  
pp. 784-802
Author(s):  
Jong-Taek Oh ◽  
Cuong Ne Ngoc
Keyword(s):  
Experimental Investigation ◽  
Heat Pump ◽  
Cold Storage ◽  
Temperature Regulation ◽  
Cfd Simulation ◽  
Coefficient Of Performance ◽  
Pump System ◽  
Heat Pump System ◽  
Simulation Process ◽  
Wasted Heat

In this study, heat pump system has been developed by CFD simulation and experimental investigation. It studies the thermal behavior of a thermobank and COP on heat pump system and cold storage. The thermobank stores the wasted heat of during refrigeration cycles and its energy is used for defrosting process and heating room. It also reduces defrosting time and condensation load so that the temperature regulation in the cold storage is constant. The system is investigated experimentally and CFD simulated under thermobank. The dimension L×W×H of cold storage is 3×1,6×1,4 m, thermobank is 600×300×400mm. The temperature of ambient on CFD simulation process is 150C.This heat pump system can be used to keep preservation of agricultural products in cold storage warehouse together with floor panel heating for room in winter. The ejector is used in system which the purpose increases in coefficient of performance (COP) and decrease in compressor displacement. As the calculated results, its COP is increased about 38% when using thermobank and ejector in heat pump system.

scholarly journals The Effect of Coupling Solar Thermal System and Geothermal Heat Pump Systems in Areas with Unbalanced Heating and Cooling Demand

Energies ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 31
Author(s):  
Jihyun Hwang ◽  
Doosam Song ◽  
Taewon Lee
Keyword(s):  
Heat Source ◽  
Water Supply ◽  
Heat Pump ◽  
Coefficient Of Performance ◽  
Maximum Temperature ◽  
Geothermal Heat ◽  
Pump System ◽  
Heat Pump System ◽  
Solar Heat ◽  
Heating And Cooling

Geothermal source heat pump (GSHP) systems as renewable energy systems are being more frequently installed as part of the zero-energy building drive. However, in South Korea, where a large amount of heating load can be required, maintaining high system performance by using only a GSHP is difficult owing to the gradual degradation of its thermal performance. The performance of a solar-assisted GSHP system was therefore experimentally analyzed and compared with a GSHP-only system. The results showed that the heating coefficient of performance of the GSHP-only operation was 5.4, while that of the solar-assisted GSHP operation was 7.0. In the case of the GSHP-only system, the maximum temperature of the heat pump water supply on the heat source side was initially 13.1 °C, but this rapidly decreased to 11.4 °C during operation. For the solar-assisted GSHP system, the temperature of the water supply to the heat source side of the heat pump was controlled at 15–20.9 °C, and the power consumption for system operation was reduced by about 20% compared with that for the GSHP-only system. Much higher temperatures could be supplied when solar heat is used instead of ground heat, as solar heat contributes to the performance improvement of the heat pump system.

scholarly journals Life cycle cost analysis of different residential heat pump systems

2020 ◽  
Vol 207 ◽  
pp. 01014
Author(s):  
Nadezhda Doseva ◽  
Daniela Chakyrova
Keyword(s):  
Energy Efficiency ◽  
Life Cycle ◽  
Heat Pump ◽  
Life Cycle Cost ◽  
Residential Buildings ◽  
Energy Performance ◽  
Coefficient Of Performance ◽  
Pump System ◽  
Heat Pump System ◽  
Heating And Cooling

Nowadays, the application of air-source heat pumps for heating and cooling in residential buildings has been increased significantly. The main occasion for this is the accessibility of a heat source for these devices - the external air. Nevertheless, the increase of the energy efficiency of the air source heat pump systems is a difficult design problem because their capacity and performance are a function of the dynamically changing parameters of the outdoor air. Because of that, the main aim of this study is to develop an approach for choosing a structural scheme of an air-to-water heat pump system under specific climatic conditions. The considered systems are monovalent, bivalent-parallel and bivalent-alternative heat pump systems. In the current paper is conducted a dynamic energy modeling of heating and cooling demand of a typical residential building situated in Varna, Bulgaria and applying the bin temperature data. It is assessed the effect of the heat pump capacity over the annual and seasonal energy performance of the heat pump systems. It is established the effect of the bivalent temperature, cut-off temperature and on-off cycles duration on rates of the criteria for techno-economic assessment. The seasonal coefficient of performance (SCOP), seasonal energy efficiency rate (SEER) and life cycle costs (LCC) of the analyzed heat pump systems are adopted as assessment parameters.

scholarly journals Performance Evaluation of an Adsorption Heat Pump System Using MSC-30/R1234yf Pair with the Impact of Thermal Masses

2021 ◽  
Vol 11 (5) ◽  
pp. 2279
Author(s):  
Sangwon Seo ◽  
František Mikšík ◽  
Yuta Maeshiro ◽  
Kyaw Thu ◽  
Takahiko Miyazaki
Keyword(s):  
Heat Pump ◽  
Adsorption Isotherms ◽  
Coefficient Of Performance ◽  
Variable Pressure ◽  
Condensation Temperature ◽  
Relative Pressure ◽  
Pump System ◽  
Adsorption Heat Pump ◽  
Adsorbed Phase ◽  
The Impact

In this study, we evaluated the performance of low Global Warming Potential (GWP) refrigerant R1234yf on the activated carbon (MSC-30) for adsorption heating applications. The adsorption isotherms of MSC-30/R1234yf were measured using a constant-volume–variable-pressure (CVVP) method from very low relative pressure to the practical operating ranges. The data were fitted with several isotherm models using non-linear curve fitting. An improved equilibrium model was employed to investigate the influence of dead thermal masses, i.e., the heat exchanger assembly and the non-adsorbing part of the adsorbent. The model employed the model for the isosteric heat of adsorption where the adsorbed phase volume was accounted for. The performance of the heat pump was compared with MSC-30/R134a pair using the data from the literature. The analysis covered the desorption temperature ranging from 60 °C to 90 °C, with the evaporation temperature at 5 °C and the adsorption temperature and condensation temperature set to 30 °C. It was observed that the adsorption isotherms of R1234yf on MSC-30 were relatively lower than those of R134a by approximately 12%. The coefficient of performance (COP) of the selected pair was found to vary from 0.03 to 0.35 depending on the heat source temperature. We demonstrated that due to lower latent heat, MSC-30/R1234yf pair exhibits slightly lower cycle performance compared to the MSC-30/R134a pair. However, the widespread adaptation of environmentally friendly R1234yf in automobile heat pump systems may call for the implementation of adsorption systems such as the direct hybridization using a single refrigerant. The isotherm and performance data presented in this work will be essential for such applications.

Performance Characteristics of a Combined Ejector-Absorption Heat Pump Using NH3-H2O

1999 ◽  
Author(s):  
D. A. Kouremenos ◽  
E. D. Rogdakis ◽  
G. K. Alexis
Keyword(s):  
Heat Pump ◽  
Gain Factor ◽  
Coefficient Of Performance ◽  
Detailed Calculation ◽  
Absorption System ◽  
Evaporator Temperature ◽  
Pump System ◽  
Heat Gain ◽  
Absorption Heat Pump ◽  
Heat Pump System

Abstract Absorption system have been investigated for many years. However, coefficient of performance COP or heat gain factor HGF for absorption systems are significantly lower than those for conventional compression systems. This has restricted their wide application. This paper discusses the behavior of mixture NH3-H2O through of an ejector, operating in an absorption heat pump system. This combination improves the performance of conventional absorption system and with the phasing out of ozone-damaging refrigerants, absorption refrigerators, heat pumps and air-conditioning now provide a potential alternative. For the detailed calculation of the proposed system a method has been developed, which employs analytical functions describing the thermodynamic properties of die mixture. The influence of three major parameters: generator, condenser and evaporator temperature, on ejector efficiency and heat gain factor of the system is discussed. Also the maximum value of HGF was estimated by correlation of above three temperatures.

Modeling of a Smart Heat Pump Made of Laminated Thermoelectric and Electrocaloric Materials

2016 ◽  
Vol 138 (4) ◽  
Author(s):  
Dudong Feng ◽  
Shi-Chune Yao ◽  
Tian Zhang ◽  
Qiming Zhang
Keyword(s):  
Heat Pump ◽  
Temperature Difference ◽  
Coefficient Of Performance ◽  
Pump System ◽  
Laminated Structure ◽  
Heat Pump System ◽  
Simple Arrangement ◽  
Parametric Effects ◽  
Hybrid Heat Pump ◽  
Physical Features

In this study, a smart heat pump, which could be used for the cooling of electronics, made of laminated structure of thermoelectric (TE) and electrocaloric (EC) materials, is studied. A simple arrangement of two TE layers sandwiched with one EC layer is modeled. This smart heat pump utilized the newly developed EC materials of giant adiabatic temperature change and the TE materials of high figure of merit. The system has the advantages of no moving parts, made of solid state, operable over large working temperature difference, and can be formed into very small size. The operation of the device is numerically modeled considering the three major parametric effects: EC operation as a function of time, electric current applied on TE, and temperature difference between the hot and cold sinks. The results on coefficient of performance (COP) and heat flow per unit area are discussed. This study is performed as an early attempt of analyzing the basic physical features of TE–EC–TE laminated structure heat pump and extends the understanding by further discussing the tradeoff between lower COP and larger overall temperature difference coverage in the TE/EC hybrid heat pump system with multilaminated structure.

Sign in / Sign up

Export Citation Format

Share Document