Potential Utilization of Higher Alcohols in Unmodified Diesel Engine

2013 ◽  
Author(s):  
Naveen Kumar ◽  
Sidharth Bansal ◽  
Vipul Vibhanshu
Keyword(s):  
Phase Separation ◽  
Diesel Engine ◽  
Specific Energy Consumption ◽  
Calorific Value ◽  
Compression Ignition ◽  
Crude Petroleum ◽  
Compression Ignition Engine ◽  
Performance And Emission ◽  
Oxygenated Fuel ◽  
Carbon Dioxide Co2

India does not have large reserves of crude petroleum and spends a huge amount of foreign exchange for importing crude petroleum. The environmental degradation caused by burning of petroleum derived fuels is also causing an ecological imbalance. Research is carried world over on renewable fuels which could either be used as an extender or substitute to petroleum origin fuels and in this context alcohols such as ethanol and butanol have an immense potential. The earlier work on use of alcohols as a blend with diesel in the compression ignition engine has suggested reduction in emissions, however, problems such as phase separation and increase in fuel consumption has also been encountered while utilizing ethanol in diesel engines. To alleviate this problem, isobutanol has the potential to be used along with ethanol to make a homogenous blend without any phase separation and simultaneous advantage of alcohol being an oxygenated fuel which shall improve the combustion and reduce emission. The present study was carried out to explore the potential utilization of ethanol-isobutanol-diesel blends (containing up to 20% ethanol-isobutanol mixture in equal proportions) in compression ignition engine. Three blends were prepared having 5%, 10%, 20% ethanol-isobutanol mixtures respectively and calorific value, kinematic viscosity; specific gravity and density of blends were found to decrease with increase in ethanol-isobutanol percentage. The engine trial was conducted on an unmodified diesel engine to evaluate the performance and emission characteristics on ethanol-isobutanol-diesel blends and results were compared with baseline data of diesel. The results obtained from the engine trial suggested that brake thermal efficiency (BTE) increased and brake specific energy consumption (BSEC) decreased for the blends and considerable reduction in carbon monoxide (CO) and carbon dioxide (CO2) was observed with blends with a small increase in unburnt hydrocarbon (UBHC). The nitrogen oxide (NOx) and smoke emissions were also found to reduce for the ethanol-isobutanol-diesel blends.

scholarly journals An Experimental Investigation on the Effect of Ferrous Ferric Oxide Nano-Additive and Chicken Fat Methyl Ester on Performance and Emission Characteristics of Compression Ignition Engine

Symmetry ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 265
Author(s):  
Ameer Suhel ◽  
Norwazan Abdul Rahim ◽  
Mohd Rosdzimin Abdul Rahman ◽  
Khairol Amali Bin Ahmad ◽  
Yew Heng Teoh ◽  
...  
Keyword(s):  
Methyl Ester ◽  
Ferric Oxide ◽  
Fossil Fuels ◽  
Specific Energy Consumption ◽  
Experimental Results ◽  
Compression Ignition ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Performance And Emission ◽  
Chicken Fat

In recent years, industries have been investing to develop a potential alternative fuel to substitute the depleting fossil fuels which emit noxious emissions. Present work investigated the effect of ferrous ferric oxide nano-additive on performance and emission parameters of compression ignition engine fuelled with chicken fat methyl ester blends. The nano-additive was included with various methyl ester blends at different ppm of 50, 100, and 150 through the ultrasonication process. Probe sonicator was utilized for nano-fuel preparation to inhibit the formation of agglomeration of nanoparticles in base fuel. Experimental results revealed that the addition of 100 ppm dosage of ferrous ferric oxide nanoparticles in blends significantly improves the combustion performance and substantially decrease the pernicious emissions of the engine. It is also found from an experimental results analysis that brake thermal efficiency (BTE) improved by 4.84%, a reduction in brake specific fuel consumption (BSFC) by 10.44%, brake specific energy consumption (BSEC) by 9.44%, exhaust gas temperature (EGT) by 19.47%, carbon monoxides (CO) by 53.22%, unburned hydrocarbon (UHC) by 21.73%, nitrogen oxides (NOx) by 15.39%, and smoke by 14.73% for the nano-fuel B20FFO100 blend. By seeing of analysis, it is concluded that the doping of ferrous ferric oxide nano-additive in chicken fat methyl ester blends shows an overall development in engine characteristics.

Preparation of Jatropha Biodiesel Using Hydrotalcite Catalyst and its Performance on Diesel Engine

2011 ◽  
Vol 110-116 ◽  
pp. 1368-1373 ◽  
Author(s):  
Amar P. Pandhare ◽  
S. G. Wagholikar ◽  
R. B. Jadhav Sachin Musale ◽  
A. S. Padalkar
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Specific Energy Consumption ◽  
Exhaust Emissions ◽  
Effect Of Temperature ◽  
Compression Ignition ◽  
Performance Parameters ◽  
Jatropha Oil ◽  
Compression Ignition Engine ◽  
Ci Engines

The heterogeneous catalyst are environment friendly and render the process simplified. A wide variety of solid bases have been examined for this process. The present work reports the use of hydrotalcite catalyst for the synthesis of Biodiesel from jatropha oil. An experimental investigation has been carried out to analyze the performance and emission characteristics of a compression ignition engine fuelled with Jatropha oil and its blends (10%, 20%, 40%, 50%, and 60 % ) with mineral diesel. The effect of temperature on the viscosity of Jatropha oil has also been investigated. A series of engine tests, have been conducted using each of the above fuel blends for comparative performance evaluation. The performance parameters evaluated include thermal efficiency, brake specific fuel consumption (BSFC), brake specific energy consumption (BSEC), and exhaust gas temperature whereas exhaust emissions include mass emissions of CO, HC, NO. These parameters were evaluated in a single cylinder compression ignition diesel engine. The results of the experiment in each case were compared with baseline data of mineral diesel. Significant improvements have been observed in the performance parameters of the engine as well as exhaust emissions. The gaseous emissions of oxide of nitrogen from all blends are lower than mineral diesel at all engine loads. Jatropha oil blends with diesel (up to 50% v/v) can replace diesel for operating the CI engines giving lower emissions and improved engine performance. More over results indicated that B20 have closer performance to diesel and B100 have lower brake thermal efficiency mainly due to its high viscosity compared to diesel.

scholarly journals Effect of di-tertiary-butyl peroxide additive on combustion, performance and emissions of a karanja methyl ester fueled diesel engine

2021 ◽  
Author(s):  
Bhabani Prasanna Pattanaik ◽  
JIBITESH KUMAR PANDA ◽  
Santhosh Kumar Gugulothu ◽  
Pradeep Kumar Jena
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Specific Energy Consumption ◽  
Calorific Value ◽  
Tertiary Butyl ◽  
Performance And Emission ◽  
Combustion Performance ◽  
Performance And Emissions ◽  
Butyl Peroxide ◽  
Karanja Oil

Abstract The present work studies the influence of di-tertiary-butyl peroxide (DTBP) as a cetane-improving additive to karanja methyl ester (KME) on the combustion, performance and emission characteristics of a diesel engine. KME produced by base catalyzed transesterification of non-edible karanja oil was blended with DTBP in different volume proportions to result KMED1 (99% KME + 1% DTBP), KMED2 (98% KME + 2% DTBP), KMED3 (97% KME + 3% DTBP) and KMED5 (95% KME + 5% DTBP) fuel blends. With increase in DTBP content, viscosity was reduced, whereas the cold flow properties, cetane index and calorific value were enhanced. Engine test results exhibited improvement in brake thermal efficiency and brake specific energy consumption for all blends compared to neat KME. Combustion analysis showed improved combustion with rise in DTBP content in the blends. The CO, HC and NOx emissions with KME-DTBP blends were less compared to neat KME and the same significantly reduced with rise in DTBP percentage in the blends. This shows improved combustion due to more oxygen availability and improvement in fuel properties with addition of DTBP to KME. However, the NOx emissions were marginally higher with KME-DTBP blends compared to neat KME and diesel that may be further studied.

scholarly journals Research on Performance And Emission on Compression Ignition Engine Fuelled With Blends of Neem Bio-Diesel

2019 ◽  
Vol 8 (6) ◽  
pp. 3732-3735
Keyword(s):  
Diesel Engine ◽  
Vegetable Oils ◽  
Castor Oil ◽  
Fossil Fuels ◽  
Emission Characteristics ◽  
Nox Emissions ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Performance And Emission

In this contemporary era it is mandatory to increasing the usage of non edible biodiesel to replace the fossil fuels. This non edible biodiesels are produced from vegetable oils which is clean burning and renewable. This paper deals with the performance and emission characteristics on diesel engine with blends of Castor oil as biodiesel. Castor oil biodiesel is prepared by the use of adding 1% v/v H2SO4 after the transesterification process. The engine tests were performed with various blends B20, B40, B60 on a single cylinder, 4-stroke, diesel engine. The result shows Higher performance and lower emissions for B20 than the diesel and other blends. The brake thermal efficiency is higher than the diesel and CO, HC and NOX emissions were 22%, 8.4%, and 21% lesser than that of diesel.

Study on Performance and Emission Characteristics of DI Diesel Engine Fuelled With Deccan Hemp Methyl Ester

2012 ◽  
Author(s):  
K. R. Balasubramanian ◽  
R. Anand ◽  
B. Venkatesh ◽  
G. R. Kannan ◽  
S. P. Sivapirakasam
Keyword(s):  
Diesel Engine ◽  
Energy Demand ◽  
Alternative Fuels ◽  
Fossil Fuels ◽  
Compression Ignition Engine ◽  
Performance And Emission ◽  
The World ◽  
Di Diesel Engine ◽  
Hemp Oil ◽  
Carbon Dioxide Co2

The world needs an alternative fuels that could maintain the world running on its wheels due to the increasing energy demand and uncertainty in availability of the fossil fuels. The present investigation analyzes the scope of utilizing the Deccan hemp oil based biodiesel derived from jute seed as an alternative to the diesel. Experimental investigation was carried out at diesel engine with different loads from 0% to 100% and 10% overload condition under a constant speed of 1500 rpm. It was found that the reduction in brake thermal efficiency and higher brake specific fuel consumption was observed with biodiesel in comparison with diesel. The carbon monoxide (CO), carbon-dioxide (CO2), unburnt hydrocarbon (HC) and nitric oxide (NO) emissions for Deccan hemp oil based biodiesel were reduced by 0.2% vol, 1.6% vol, 62.5%, 36.84% whereas slightly higher smoke emission was observed when compared to diesel fuel. These studies revealed that Deccan hemp oil based biodiesel can be used as a fuel in compression ignition engine without any engine modifications.

Performance and Emission Evaluation of a Diesel Engine Fuelled with Cashew Nut Shell Oil Blends

2014 ◽  
Vol 984-985 ◽  
pp. 893-899 ◽  
Author(s):  
S. Santhanakrishnan ◽  
S. Jose
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Experimental Tests ◽  
Emission Characteristics ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Performance And Emission ◽  
Oil Blends ◽  
Cashew Nut ◽  
Cashew Nut Shell

This paper presents the properties and application of cashew nut shell oil as blend component for diesel in compression ignition engine. Experimental tests were carried out in a single cylinder, four stroke, direct injection, compression ignition engine fueled with cashew nut shell oil blends. During the experiments, the performance and emission characteristics of the diesel engine was analyzed and compared with the neat diesel fuel performance.

Studies on Esters of Coconut Oil as Fuel for LPG-Biodiesel Dual Fuel Engine

2003 ◽  
Author(s):  
N. Kapilan ◽  
R. P. Reddy ◽  
P. Mohanan
Keyword(s):  
Diesel Engine ◽  
Coconut Oil ◽  
Poor Performance ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Performance And Emission ◽  
Mode Operation ◽  
Pilot Fuel

The rapid depletion in world petroleum reserves and uncertainty in petroleum supply due to political and economical reasons, as well as, the sharp escalation in the petroleum prices, have stimulated the search for alternatives to petroleum based fuels specially diesel and gasoline. Biodiesel is one of the renewable fuels, which will be the good replacement to diesel. But as a sole fuel, it gives poor performance and higher emissions. From the literature survey, it is observed that not much work has been done to use Methyl Ester (ME) of coconut oil as liquid fuel in sole and dual fuel mode of operation. Hence, in the present work, ME of coconut oil is chosen as a sole fuel to run the diesel engine and an alternative pilot fuel to run LPG-Biodiesel dual fuel engine. In dual fuel mode operation, LPG is used as the inducted gaseous fuel. LPG has been chosen as the inducted fuel on account of its easy availability in abundance in the present time. The existing compression ignition diesel engine was modified to work on dual fuel mode. Tests were carried out on a single cylinder, four strokes, water-cooled, direct injection, compression ignition engine using ME of coconut oil as fuel. To study the effect of injection timing, its is advanced and retarded from the standard injection timing recommended for diesel operation. From the results, it is observed that the advanced injection timing results in better performance and lower emissions of the diesel engine. In dual fuel mode operation, first the engine was started with ME of coconut oil as fuel and then the LPG flow rate was increased. With appropriate proportions of the injected (0.45, 0.65 and 0.75 kg/hr) and inducted fuels it is possible to improve the engine performance and reduce its emissions. From the experimental results, it is found that the pilot fuel rate of 0.65 kg/hr is preferred from the point view of brake thermal efficiency, fuel consumption and smooth running. ME of coconut oil were successfully used as sole fuel and pilot fuel. The performance and emission of the engine in sole fuel mode with better injection timing and dual fuel mode with better pilot quantity were compared. From the comparison, it is observed that the ME of coconut oil can be used as pilot fuel in dual fuel engine compared to sole fuel with regard to performance and emissions.

scholarly journals Bio-ketones from lignocellulosic biomass: experimental investigation on fuel properties, combustion and emissions characteristics of cyclopentanone blend with diesel in compression ignition engine

2017 ◽  
Vol 171 (4) ◽  
pp. 81-86
Author(s):  
Omid DOUSTDAR ◽  
Miroslaw WYSZYNSKI ◽  
Athanasios TSOLAKIS ◽  
Hamid MAHMOUDI
Keyword(s):  
Molecular Structure ◽  
Surface Tension ◽  
Diesel Engine ◽  
Lignocellulosic Biomass ◽  
Diesel Fuel ◽  
Calorific Value ◽  
Fuel Properties ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Conventional Diesel Fuel

Use of alternative fuels in compression ignition engines is the topic for many studies. This paper presents the results of lubricity, calorific value, viscosity, surface tension and density of a ketone blend with diesel to use as a fuel in compression ignition engine. Analyses of fuel properties are vital due to their effect on fuel system. In addition, this study is related to the development of future biofuels and it indicates the effect of oxygen double bond in molecular structure of ketones on important fuel properties. Cyclopentanone which has cyclic molecular structure was used; it can be produced from lignocellulosic biomass through various processing ways. This ketone was blended with diesel fuel at 10% vol. Results from fuel properties tests were compared to the conventional diesel fuel. In the next step this blend was tested in a research diesel engine to analyse its combustion behaviour and emission characteristics of exhaust gases; these results were compared with ultra-low sulphur diesel fuel. Results showed that cyclopentanone, as an additive to diesel, improved surface tension and density of the fuel but in contrast had negative effect on viscosity, lubricity and calorific value of the fuel, but still in the standard range. Combustion behaviour of this fuel in the diesel engine also showed longer ignition delay of ketone blend and also that gaseous emission such as CO and THC are higher than from diesel fuel and NOx emission is less than from conventional diesel fuel combustion.

An Experimental Investigation of Diesel Engine Fuelled with MgO Nano Additive Biodiesel - Diesel Blends

2019 ◽  
Vol 1 (2) ◽  
pp. 28-34
Author(s):  
Vijayakumar C ◽  
Murugesan A ◽  
Subramaniam D ◽  
Panneerselvam N
Keyword(s):  
Experimental Investigation ◽  
Diesel Engine ◽  
Calorific Value ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Fuel Blends ◽  
Compression Ignition Engines ◽  
Performance And Emissions ◽  
Nano Additives ◽  
Blended Fuels

In this experimental investigation compacts the performance and emissions of compression ignition engines fuelled with MgO nano additive, maducaindica bio diesel blends were examined. Based upon the previous literatures only 20% mahuca methyl ester fuel blends without nano additives is suitable for compression ignition engine without affecting engine efficiency and its characteristics. In this paper magnesium oxide nano additives are added into the 40% Mahucaindica biodiesel- diesel blends at the rate of 50ppm for developing the test fuels. In this nano additives improve the properties of diesel fuel like viscosity, calorific value and decreased the flash point and fire point. Then compared the performance and emissions differences of all blended fuels used as a fuel in a diesel engine. The observation of results, 40MgO + 50ppm blended fuels brake thermal efficiency is improved then CO, HC, CO2and smoke decreased compared to other fuel blends. The results are taken into account, a blend of 40MgO+ Mgo50ppm is the best blend ratio compared than other blends with nano additives.

Sign in / Sign up

Export Citation Format

Share Document