Analysis of an Adsorption Chiller Cooling System for Various Types of Solar Collectors Using the F-Chart Cooling Method

2016 ◽  
Author(s):  
I. P. Koronaki ◽  
E. G. Papoutsis ◽  
M. T. Nitsas
Keyword(s):  
Solar Energy ◽  
Flat Plate ◽  
Cooling System ◽  
Energy Performance ◽  
Electrical Network ◽  
Climatic Data ◽  
Solar Collectors ◽  
Adsorption Chiller ◽  
Solar Cooling ◽  
Cooling Method

Solar cooling systems offer a reliable and environmentally friendly alternative to conventional electrically driven vapor compression cooling units. Air conditioning systems powered by solar energy are very attractive because they have zero ozone depletion and global warming potential, their operational cost is low and they do not burden the electrical network during summer months. In this study, the installation of a solar cooling system in various Greek cities is examined. The system utilizes a single-stage, two-bed silica gel-water adsorption chiller driven by heat produced by solar collectors. A lumped parameter model is used to simulate the performance of the adsorption chiller. The optimum tilt of the solar collectors is calculated for each examined city in order for the collected solar energy to be maximized during the summer period (April to September). The climatic data are taken from the technical notes of Greek Regulation for Buildings Energy Performance. Then, using the f-chart cooling method the necessary collectors’ surface area is estimated for every examined city and for different types of flat plate collectors (including advanced flat plate, simple flat plate and hybrid photovoltaic thermal collectors).

Experimental Daily Energy Performance of Flat Plate and Evacuated Tube Solar Collectors

2009 ◽  
Author(s):  
Enrico Zambolin ◽  
Davide Del Col ◽  
Andrea Padovan
Keyword(s):  
Solar Energy ◽  
Flat Plate ◽  
Energy Performance ◽  
Hot Water ◽  
Solar Collectors ◽  
Input Output ◽  
Evacuated Tube Collector ◽  
Daily Energy ◽  
Radiation Test ◽  
Evacuated Tube

New comparative tests on different types of solar collectors are presented in this paper. Tests have been performed at the solar energy conversion laboratory of the University of Padova. Two standard glazed flat plate collectors and one evacuated tube collector are installed in parallel; the evacuated collector is a direct flow through type with external CPC (compound parabolic concentrator) reflectors. The present test rig allows to make measurements on the flat plate, on the evacuated collector or on both simultaneously, by simply acting on the valves to modify the circuit. In this paper measurements of the performance of the evacuated tube collector and flat plate collectors working at the same conditions are reported. Efficiency in stationary conditions is measured following the standard EN 12975-2 [1] and it is compared with the input/output curves measured for an entire day. The main purpose of the present work is to characterize and to compare the daily energy performance of the two types of collectors. An effective mean for describing and analyzing the daily performance is the so called input/output diagram, in which the collected solar energy is plotted against the daily incident solar radiation. Test runs have been performed in several conditions to reproduce different conventional uses (hot water, space heating, solar cooling).

scholarly journals A dynamic model of an innovative high-temperature solar heating and cooling system

2016 ◽  
Vol 20 (4) ◽  
pp. 1121-1133 ◽  
Author(s):  
Annamaria Buonomano ◽  
Francesco Calise ◽  
Maria Vicidomini
Keyword(s):  
High Temperature ◽  
Simulation Model ◽  
Flat Plate ◽  
Cooling System ◽  
Energy Performance ◽  
Economic Feasibility ◽  
Solar Heating ◽  
Hot Water ◽  
Solar Collectors ◽  
Heating And Cooling

In this paper a new simulation model of a novel solar heating and cooling system based on innovative high temperature flat plate evacuated solar thermal collector is presented. The system configuration includes: flat-plate evacuated solar collectors, a double-stage LiBr-H2O absorption chiller, gas-fired auxiliary heater, a closed loop cooling tower, pumps, heat exchangers, storage tanks, valves, mixers and controllers. The novelty of this study lies in the utilization of flat-plate stationary solar collectors, manufactured by TVP Solar, rather than concentrating ones (typically adopted for driving double-stage absorption chillers). Such devices show ultra-high thermal efficiencies, even at very high (about 200?C) operating temperatures, thanks to the high vacuum insulation. Aim of the paper is to analyse the energy and economic feasibility of such novel technology, by including it in a prototypal solar heating and cooling system. For this purpose, the solar heating and cooling system design and performance were analysed by means of a purposely developed dynamic simulation model, implemented in TRNSYS. A suitable case study is also presented. Here, the simulated plant is conceived for the space heating and cooling and the domestic hot water production of a small building, whose energy needs are fulfilled through a real installation (settled also for experimental purposes) built up close to Naples (South Italy). Simulation results show that the investigated system is able to reach high thermal efficiencies and very good energy performance. Finally, the economic analysis shows results comparable to those achieved through similar renewable energy systems.

Sustainable Cooling with Hybrid Concentrated Photovoltaic Thermal (CPVT) System and Hydrogen Energy Storage

2018 ◽  
Vol 1 (2) ◽  
pp. 40-51 ◽  
Author(s):  
Muhammad Burhan ◽  
Muhammad Wakil Shahzad ◽  
Kim Choon Ng
Keyword(s):  
Energy Storage ◽  
Solar Energy ◽  
Optimization Algorithm ◽  
Concentration Ratio ◽  
Cooling System ◽  
Renewable Energy Sources ◽  
Hot Water ◽  
Hydrogen Energy ◽  
Adsorption Chiller ◽  
Back Plate

Standalone power systems have vital importance as energy source for remote area. On the other hand, a significant portion of such power production is used for cooling purposes. In this scenario, renewable energy sources provide sustainable solution, especially solar energy due to its global availability. Concentrated photovoltaic (CPV) system provides highest efficiency photovoltaic technology, which can operate at x1000 concentration ratio. However, such high concentration ratio requires heat dissipation from the cell area to maintain optimum temperature. This paper discusses the size optimization algorithm of sustainable cooling system using CPVT. Based upon the CPV which is operating at x1000 concentration with back plate liquid cooling, the CPVT system size is optimized to drive a hybrid mechanical vapor compression (MVC) chiller and adsorption chiller, by utilizing both electricity and heat obtained from the solar system. The electrolysis based hydrogen is used as primary energy storage system along with the hot water storage tanks. The micro genetic algorithm (micro-GA) based optimization algorithm is developed to find the optimum size of each component of CPVT-Cooling system with uninterrupted power supply and minimum cost, according to the developed operational strategy. The hybrid system is operated with solar energy system efficiency of 71%.

scholarly journals Experimental Performance Evaluation of an Integrated Solar-Driven Adsorption System in Terms of Thermal Storage and Cooling Capacity

Energies ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5931
Author(s):  
M.T. Nitsas ◽  
E.G. Papoutsis ◽  
I.P. Koronaki
Keyword(s):  
Energy Production ◽  
Cooling System ◽  
Thermal Storage ◽  
Cooling Capacity ◽  
Climatic Conditions ◽  
Environmentally Benign ◽  
Heat Sources ◽  
Adsorption Chiller ◽  
Solar Cooling ◽  
Dual Bed

Heat-driven coolers provide a reliable and environmentally benign alternative to traditional electrically powered chillers. Their main advantage is that they can be driven using low enthalpy heat sources. A solar system is installed at the school of Mechanical Engineering of National Technical University of Athens in order to examine the potential of thermal storage and solar cooling under Athens climatic conditions. The cooling effect is produced using a dual bed, single stage, zeolite/water adsorption chiller with cooling capacity of 10 kW at its nominal conditions of operation. Both vacuum tube collectors and hybrid photovoltaic thermal collectors are installed in order to supply the system with heat. The system is evaluated in terms of solar collectors’ useful energy production, heat stored in the intermediate buffer and cooling system’s performance. It is observed that the cooling system operates satisfactorily under Athens climatic conditions achieving a maximum cooling capacity of 3.7 kW and an average COP around 0.5.

scholarly journals Performance Assessment of Solar Cooling Systems with Energy Storage

2021 ◽  
Vol 312 ◽  
pp. 08014
Author(s):  
Giovanni Brumana ◽  
Giuseppe Franchini ◽  
Elisa Ghirardi
Keyword(s):  
Cooling System ◽  
Evaporative Cooling ◽  
Optimal Size ◽  
Ambient Conditions ◽  
Absorption Chiller ◽  
Cooling Systems ◽  
Detailed Model ◽  
Adsorption Chiller ◽  
Solar Cooling ◽  
Evaporative Cooling System

The paper presents a complete solar cooling comparison. A detailed model of a tertiary sector building has been evaluated in three locations (Riyadh, Abu Dhabi, and Palermo) and coupled with four solar cooling systems: two solar thermal cooling systems (Li-Br absorption chiller and adsorption chiller), a solar Desiccant Evaporative Cooling system and a solar electric cooling (Photovoltaic coupled with Compression chiller). A multi-variable optimization procedure selects the optimal size of each component. The results show that the solar cooling system based on absorption chiller satisfied the cooling demand regardless of the site location whilst the performance of the Desiccant Evaporative Cooling system is dramatically affected by ambient conditions. The electric solar cooling option shows the best overall efficiency and appears a costeffective solution despite the high cost of the storage system.

Design and Analysis of Solar Tracking System for Multipurpose Domestic Applications

2013 ◽  
Author(s):  
P. Rhushi Prasad ◽  
P. B. Gangavati ◽  
H. V. Byregowda ◽  
K. S. Badarinarayan
Keyword(s):  
Solar Energy ◽  
Energy Conversion ◽  
Flat Plate ◽  
Tracking System ◽  
Solar Collectors ◽  
Tracking Systems ◽  
Pv Panel ◽  
Energy Conversion Systems ◽  
Flat Plate Collector ◽  
Parabolic Collector

Now-a-days the field of applied mechanical systems opens new horizons for the use of orientation mechanisms. The opportunity to use mechanisms with a “sustainable purpose” leads to new approaches in the development of renewable energy systems design. The evaluation of the existing products shows that the tracking mechanisms for solar energy conversion systems may improve the efficiency of the solar energy conversion systems up to 30% to 50%. Applications of solar energy for domestic and industrial heating purposes have been becoming very popular. However the effectiveness of presently used fixed flat plate collectors, PV panels and parabolic collector are low due to the moving nature of the energy source. The presents research was carried out in the field of increasing the efficiency of the solar energy received by the solar collectors like PV panels, Flat plate collectors, Cylindrical Parabolic collectors using tracking systems by changing the position of the solar collectors correlated to the sun position for getting maximum radiation use of beam radiation falling on the solar collector. Two main aspects are taken into consideration, one optimizing the interaction between the mechatronic system components by integrating the analog electronic system by using a 555 timer in the mechanical model, and secondly by reducing the cost & time for the design process. The research work was carried out for location in chickballapur district at BGS R&D centre in Karnataka State, India. The results obtained in work is 24% increase in tracking efficiency of experimental model of flat plate collector, 30% increase in tracking efficiency in working model flat plate collector, 39 % increase in tracking efficiency of cylindrical parabolic collector and 36% increases in tracking efficiency of the Photovoltaic panel is found when compared to the non-tracking systems respectively. This paper presents the results of PV panel collector in detail for increasing the efficiency of the PV panel collector by tracking system with comparison of non-tracking system.

Optimization of Stationary Flat-Plate Solar Collectors

2015 ◽  
Author(s):  
Singiresu S. Rao
Keyword(s):  
Game Theory ◽  
Solar Energy ◽  
Flat Plate ◽  
Solar Collector ◽  
Probabilistic Approach ◽  
Design Parameters ◽  
Theory Approach ◽  
Solar Collectors ◽  
Beam Radiation ◽  
The Game Theory

The optimum design of stationary flat-plate solar collectors is considered using the game theory approach for multiple objectives. The clear day solar beam radiation and diffuse radiation at the location of the solar collector are estimated. Three objectives are considered in the optimization problem formulation: maximization of the annual average incident solar energy, maximization of the lowest month incident solar energy and minimization of the cost. The game theory solution represents the best compromise in terms of the supercriterion selected. Because some design parameters such as solar constant, altitude, typical day of each month and most of the design variables are not precisely known, a probabilistic approach is also proposed in this work. The results obtained by the determinist and probabilistic approaches are compared. It is found that the absolute value of each objective function decreases with an increase in either the probability of constraint satisfaction or the coefficient of variation of the random variables. This work represents the first work aimed at the application of multi-objective optimization strategy, particularly the game theory approach, for the solution of the solar collector design problem.

scholarly journals Study and Analysis by Numerical Simulation of a Solar Continuous Adsorption Chiller

2015 ◽  
Vol 773-774 ◽  
pp. 605-609
Author(s):  
Rabah Gomri ◽  
Billel Mebarki
Keyword(s):  
Solar Energy ◽  
Cooling System ◽  
Recovery Process ◽  
Cooling Capacity ◽  
Coefficient Of Performance ◽  
Solar Collectors ◽  
Adsorption Refrigeration ◽  
Continuous Adsorption ◽  
Adsorption Cooling System ◽  
Mass Recovery

Environment and energy problems over the world have motivated researchers to develop energy systems more sustainable, having as one of the possible alternative the use of solar energy as source for cooling systems. Adsorption refrigeration systems are regarded as environmentally friendly alternatives to conventional vapour compression refrigeration systems, since they can use refrigerants that do not contribute to ozone layer depletion and global warming. In this paper a performance comparison between a solar continuous adsorption cooling system without mass recovery process and solar continuous adsorption cooling system with mass recovery process is carried out. Silica-Gel as adsorbent and water as refrigerant are selected. The results show that the adsorption refrigeration machine driven by solar energy can operate effectively during four months and is able to produce cold continuously along the 24 hours of the day. The importance of the mass recovery is proved in this study by increasing the coefficient of performance and the cooling capacity produced. For the same cooling capacity produced, the required number of solar collectors with mass recovery system is lower than the required number of solar collectors in the case of the refrigeration unit without mass recovery. For the same cooling capacity the system with mass recovery process allowed lower generation temperature.

Performance of a Solar Desiccant Cooling System

1988 ◽  
Vol 110 (3) ◽  
pp. 165-171 ◽  
Author(s):  
George O. G. Lo¨f ◽  
Gerald Cler ◽  
Thomas Brisbane
Keyword(s):  
Heat Exchange ◽  
Solar Energy ◽  
Cooling System ◽  
Evaporative Cooling ◽  
Hot Water ◽  
Colorado State University ◽  
Energy Applications ◽  
Solar Cooling ◽  
Cooling Unit ◽  
Electric Boiler

A solar desiccant cooling system was operated at the Solar Energy Applications Laboratory, Colorado State University, throughout the 1986 summer. The system comprises an American Solar King fresh air heating/desiccant evaporative cooling unit, a Sunmaster evacuated tube solar collector, hot water solar storage tank, auxiliary electric boiler, controls, and accessories. The cooling unit is operated in the ventilation mode, fresh air being dried in a rotating desiccant matrix, and cooled by heat exchange and evaporative cooling. Return air is used as a cooling medium in a rotating heat exchange matrix, heated by solar energy in a heat exchange coil, and discarded through the rotating desiccant bed. The solar-driven system provided over 90 percent of the seasonal cooling requirements in an experimental, residence type building at average COP levels of 1.0 and solar collection efficiencies of 50 percent when supplied with solar heated water at temperatures of 50 to 65° C. Detailed operating results, including total and average solar cooling provided, coefficients of performance, and overall solar cooling performance ratios are presented.

Sign in / Sign up

Export Citation Format

Share Document