Evaluation of Soybean Oil-Based MQL As a Potential Replacement for Emulsion Flood Cooling Strategy for High-Speed Face Milling of Inconel 718

2020 ◽  
Author(s):  
Anthony Chukwujekwu Okafor ◽  
Theodore Obumselu Nwoguh
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Soybean Oil ◽  
Flow Rate ◽  
Wear Mechanism ◽  
Inconel 718 ◽  
Face Milling ◽  
Flow Rates ◽  
Oil Flow ◽  
Tool Wear Mechanism

Abstract This paper presents the results of comparative evaluation of soybean oil based MQL oil flow rates at 10, 30, 50, 70, and 90 ml/h with emulsion flood coolant (EC) at 1200 l/h as a benchmark in face milling of Inconel 718 using coated carbide inserts. Resultant cutting force, tool wear/ mechanism, and surface roughness are the machining performance parameters analyzed. The results show that MQL oil flow rate at 70 ml/h gave the least tool wear comparable to that of EC, while 10 ml/h gave the highest tool wear. Also, 70 ml/h gave the lowest resultant cutting force among all MQL flow rates. Increasing soybean oil-based MQL flow rate improves surface roughness and reduces tool wear by providing enough thin lubrication film but also leads to an increase in chip affinity and formation of large built-up-edges (BUEs) as the MQL flow rate reaches 90 ml/h. At lower soybean oil-based MQL flow rate, tool wear mechanism is predominantly abrasion due to large surface friction, while at higher soybean oil-based MQL flow rate, tool wear mechanism is adhesion leading to excessive BUEs. Soybean oil-based MQL flow rate at 70 ml/h is recommended when face milling Inconel 718 and is demonstrated to be a potential replacement of EC for machining difficult-to-cut metal.

Investigation on laser-induced oxidation assisted micro-milling of Inconel 718

2020 ◽  
Vol 234 (8) ◽  
pp. 1102-1112 ◽  
Author(s):  
Hongjun Xia ◽  
Guolong Zhao ◽  
Maoshun Hu ◽  
Liang Li ◽  
Aqib Mashood Khan ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Wear Mechanism ◽  
Inconel 718 ◽  
Micro Milling ◽  
Hybrid Process ◽  
Hybrid Machining ◽  
Burr Size ◽  
Tool Wear Mechanism ◽  
Coating Delamination

Poor surface quality and rapid tool wear are the main problems in micro-cutting of Inconel 718. In this study, a novel hybrid machining method named laser-induced oxidation assisted micro-milling is proposed to solve the aforementioned problems. A loose oxide layer and a relatively flat sublayer are formed on the material after laser irradiation. Under optimized laser parameters with a scanning speed of 1 mm/s and an average laser power of 4.5 W, the thicknesses of the oxide layer and the sublayer are 24 and 18 μm, respectively. The influence of cutting parameters on milling force, surface roughness, surface quality, and top burr size is studied in detail. Cutting force and thrust force in the proposed hybrid machining process are lower than those in the conventional micro-milling. Results show that for the investigated range of parameters, the optimal feed per tooth and depth of cut in the hybrid process are 3 μm/z and 3 μm, respectively. When using the optimal parameters, the surface roughness of the machined slot bottom is 108.5 nm. The top burr size on the up-milling side and the down-milling side is 26.8 and 36.2 μm, respectively. In addition, the tool wear mechanism is coating delamination in hybrid process, whereas chipping, coating delamination, tool nose breakage, and adhesion are the main tool wear mechanism in the conventional micro-milling. For the same amount of material removal, the proposed hybrid process can decrease the tool wear and enhance the service life of the micro-end mill as compared to conventional micro-milling.

scholarly journals Tool wear mechanism of turning Inconel 718 and EEMD-based feature analysis

2021 ◽  
Vol 2044 (1) ◽  
pp. 012085
Author(s):  
Delong Dong ◽  
Taoyuan Li ◽  
Xiangyu Wang ◽  
Yang Qiao ◽  
Peiquan Guo
Keyword(s):  
Tool Wear ◽  
Wear Mechanism ◽  
Inconel 718 ◽  
Feature Analysis ◽  
Tool Wear Mechanism

Effect of tool wear on the surface integrity of Inconel 718 in face milling with cemented carbide tools

Wear ◽  
2021 ◽  
pp. 203752
Author(s):  
A.R.F. Oliveira ◽  
L.R.R. da Silva ◽  
V. Baldin ◽  
M.P.C. Fonseca ◽  
R.B. Silva ◽  
...  
Keyword(s):  
Tool Wear ◽  
Surface Integrity ◽  
Inconel 718 ◽  
Face Milling ◽  
Cemented Carbide ◽  
Cemented Carbide Tools

Influence of cryogenic treatment of cutting tool inserts on tool wear and surface roughness during milling of Inconel 718

2020 ◽  
Author(s):  
Ivan Sunit Rout ◽  
P. Pal Pandian ◽  
Manish Mathew ◽  
Kevin Lobo Ivan ◽  
Shomyajit Misra
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Inconel 718 ◽  
Cutting Tool ◽  
Cryogenic Treatment

An Experimental Investigation of Oil-Buffered Shaft Seal Flow Rates

1985 ◽  
Vol 107 (1) ◽  
pp. 170-180
Author(s):  
W. N. Shade ◽  
D. E. Hampshire
Keyword(s):  
Experimental Investigation ◽  
Flow Rate ◽  
Primary Objective ◽  
Shaft Seal ◽  
Flow Rates ◽  
Process Gas ◽  
Face Seals ◽  
Oil Flow ◽  
Seal Oil ◽  
Oil Exposure

An experimental investigation was conducted to identify an optimum oil-buffered shaft seal for use on centrifugal compressors, with the primary objective being minimal seal oil exposure to process gases that cause seal oil degradation or are toxic. Types of seals tested included smooth bore cylindrical bushings, spiral groove cylindrical bushings, radial outward-flow face seals, and radial inward-flow face seals. The influence of shaft speed, gas pressure, seal oil differential pressure, oil bypass flow rate, and oil supply temperature on process side seal oil flow rate was determined. The investigation revealed some surprising relationships between seal oil flow rates and the escape of process gas.

scholarly journals Milling Inconel 718 Workpiece With Cryogenically Treated And Untreated Cutting Tools

2021 ◽  
Author(s):  
Hüseyin Gürbüz ◽  
Şehmus Baday
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Abrasive Wear ◽  
Inconel 718 ◽  
Cutting Tool ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Tool Wear ◽  
Feed Force

Abstract Although Inconel 718 is an important material for modern aircraft and aerospace, it is a kind material, which is known to have low machinability. Especially, while these types of materials are machined, high cutting temperatures, BUE on cutting tool, high cutting forces and work hardening occur. Therefore, in recent years, instead of producing new cutting tools that can withstand these difficult conditions, cryogenic process, which is a heat treatment method to increase the wear resistance and hardness of the cutting tool, has been applied. In this experimental study, feed force, surface roughness, vibration, cutting tool wear, hardness and abrasive wear values that occurred as a result of milling of Inconel 718 material by means of cryogenically treated and untreated cutting tools were investigated. Three different cutting speeds (35-45-55 m/min) and three different feed rates (0.02-0.03-0.04 mm/tooth) at constant depth of cut (0.2 mm) were used as cutting parameters in the experiments. As a result of the experiments, lower feed forces, surface roughness, vibration and cutting tool wear were obtained with cryogenically treated cutting tools. As the feed rate and cutting speed were increased, it was seen that surface roughness, vibration and feed force values increased. At the end of the experiments, it was established that there was a significant relation between vibration and surface roughness. However, there appeared an inverse proportion between abrasive wear and hardness values. While BUE did not occur during cryogenically treated cutting tools, it was observed that BUE occurred in cutting tools which were not cryogenically treated.

Sign in / Sign up

Export Citation Format

Share Document