Study of Effect of Repetition Rate on Laser Shock Peening Using Finite Element Modeling

2020 ◽  
Author(s):  
Sai Kosaraju ◽  
Xin Zhao
Keyword(s):  
Shock Wave ◽  
Residual Stress ◽  
Finite Element ◽  
Shock Waves ◽  
Repetition Rate ◽  
High Repetition Rate ◽  
Stress Profile ◽  
Surface Residual Stress ◽  
Residual Stress Profile ◽  
High Repetition

Abstract A two-dimensional finite element model is developed to simulate the interaction between metal samples and laser-induced shock waves. Multiple laser impacts are applied at each location to increase plastically affected depth and compressive stress. The in-depth and surface residual stress profiles are analyzed at various repetition rates and spot sizes. It is found that the residual stress is not sensitive to repetition rate until it reaches a very high level. At extremely high repetition rate (100 MHz), the delay between two shock waves is even shorter than their duration, and there will be shock wave superposition. It is revealed that the interaction of metal with shock wave is significantly different, leading to a different residual stress profile. Stronger residual stress with deeper distribution will be obtained comparing with lower repetition rate cases. The effect of repetition rate at different spot sizes is also studied. It is found that with larger laser spot, the peak compressive residual stress decreases but the distribution is deeper at extremely high repetition rates.

Finite element modeling of residual stress profile patterns in hard turning

2009 ◽  
Vol 24 (S1) ◽  
pp. S22-S25
Author(s):  
Y. B. Guo ◽  
S. Anurag
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Finite Element Modeling ◽  
Hard Turning ◽  
Internal State ◽  
Stress Profile ◽  
Surface Residual Stress ◽  
Mechanical Coupling ◽  
Element Modeling ◽  
Stress Profiles

Hard turning, i.e., turning hardened steels, may produce the unique “hook” shaped residual stress (RS) profile characterized by surface compressive RS and subsurface maximum compressive RS. However, the formation mechanism of the unique RS profile is not yet known. In this study, a novel hybrid finite element modeling approach based on thermal-mechanical coupling and internal state variable plasticity model has been developed to predict the unique RS profile patterns by hard turning AISI 52100 steel (62 HRc). The most important controlling factor for the unique characteristics of residual stress profiles has been identified. The transition of maximum residual stress at the surface to the subsurface has been recovered by controlling the plowed depth. The predicted characteristics of residual stress profiles favorably agree with the measured ones. In addition, friction coefficient only affects the magnitude of surface residual stress but not the basic shape of residual stress profiles.

A New Finite Element Approach Without Chip Formation to Predict Residual Stress Profile Patterns in Metal Cutting

2009 ◽  
Author(s):  
S. Anurag ◽  
Y. B. Guo ◽  
Z. Q. Liu
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Hard Turning ◽  
Metal Cutting ◽  
Cutting Speed ◽  
Stress Profile ◽  
Residual Stress Profile ◽  
Stress Prediction ◽  
Element Approach ◽  
Stress Profiles

Residual stress prediction in hard turning has been recognized as one of the most important and challenging tasks. A hybrid finite element predictive model has been developed with the concept of plowed depth to predict residual stress profiles in hard turning. With the thermo-mechanical work material properties, residual stress has been predicted by simulating the dynamic turning process followed by a quasi-static stress relaxation process. The residual stress profiles were predicted for a series of plowed depths potentially encountered in machining. The predicted residual stress profiles agree with the experimental one in general. A transition of residual stress profile has been recovered at the critical plowed depth. In addition, the effects of cutting speed, friction coefficient and inelastic heat coefficient on residual stress profiles have also been studied and explained.

Simulation of shock waves at high repetition rate of laser sparks

2001 ◽  
Vol 31 (4) ◽  
pp. 283-284 ◽  
Author(s):  
V N Tishchenko ◽  
Gennadii N Grachev ◽  
A I Gulidov ◽  
V I Zapryagaev ◽  
V G Posukh
Keyword(s):  
Shock Waves ◽  
Repetition Rate ◽  
High Repetition Rate ◽  
High Repetition

Numerical Analysis of the Effect of Machining on the Depth of Yield, Maximum Firing Pressure and Residual Stress Profile in an Autofrettaged Gun Tube

2003 ◽  
Vol 125 (3) ◽  
pp. 342-346 ◽  
Author(s):  
Amer Hameed ◽  
R. D. Brown ◽  
J. G. Hetherington
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Optimization Technique ◽  
Circumferential Stress ◽  
Element Model ◽  
Stress Profile ◽  
Residual Stress Field ◽  
Element Analysis ◽  
Residual Stress Profile ◽  
Experimental Findings

A multi-linear kinematic, two dimensional finite element model incorporating Bauschinger effect, developed using ANSYS commercial software is used to determine the effect of machining both at the bore and at the outside diameter, on the depth of yield, maximum firing pressure and final residual stress field present in an autofrettaged gun tube. The model, which is in good agreement with experimental findings, clearly shows that the reduction in maximum compressive circumferential stress is more sensitive to internal machining than to external machining; the depth of yield remains stable and there is no movement of the elastic-plastic interface, relative to its location before material removal. If the internal machining removes material in which reverse yield has occurred, the maximum firing pressure is not affected. The finite element analysis supported by experimental evidence thus leads to an optimization technique for gun tube design.

Study of the Effect of Thickness on the Residual Stress Profile of a Cold Spray Coating by Finite Element Analysis

2021 ◽  
Author(s):  
Felipe Torres ◽  
Ruben Fernandez
Keyword(s):  
Residual Stress ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Cold Spray ◽  
Spray Coating ◽  
Stress Profile ◽  
Element Analysis ◽  
Residual Stress Profile ◽  
Cold Spray Coating ◽  
The Impact

Abstract The understanding of residual stress is of critical importance in the cold spray and thermal spray processes. It has a direct effect on the integrity of the coating related to the adhesion strength, fatigue life, and can lead to undesired effects such as the delamination of the coating. In cold spray, several investigations have evaluated the impact of the residual stress on the coatings, and it is generally accepted that cold spray coatings follow a similar profile to those obtained in the shot peening process. Although the measurement of residual stresses gives fundamental insight into the process, the estimation of such stresses considering the deposition of each layer by numerical methods has not been extensively studied. This work proposes a method for analyzing the evolution of residual stress on a cold spray coating, both on the coating and the substrate, as a function of the deposited layers, using Finite Element Analysis (FEA). The evolution of the residual stress profile with the coating thickness was obtained along the transverse direction. The results were compared to experimental and numerical data from previous studies. The influence of the deposition of each layer on the residual stress profile has been discussed.

Assessment of Residual Stress Profiles for Fitness for Service Assessment of Pipe Girth Welds

2014 ◽  
Author(s):  
Pingsha Dong ◽  
Shaopin Song ◽  
Jinmiao Zhang
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Solution Procedure ◽  
Stress Profile ◽  
Full Field ◽  
Residual Stress Profile ◽  
Estimation Scheme ◽  
Detailed Assessment ◽  
Stress Profiles ◽  
Girth Welds

This paper aims to provide a detailed assessment of some of the existing residual stress profiles prescribed in widely used fitness-for-service assessment codes and standards, such as BS 7910 Appendix Q, by taking advantage of some comprehensive residual studies that become available recently. After presenting a case study on which residual stress measurements are available for validating finite element based residual stress solution procedure, residual stress profiles stipulated in BS 7910 for girth welds are evaluated in the context of a series of parametric finite element results and a shell theory based full-field residual stress estimation scheme. As a result, a number of areas for improvement in residual stress profile development are identified, including some specific considerations on how to attain some of these improvements.

Finite Element Thermal/Mechanical Analysis of Transmission Laser Microjoining of Titanium and Polyimide

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
Ankitkumar P. Dhorajiya ◽  
Mohammed S. Mayeed ◽  
Gregory W. Auner ◽  
Ronald J. Baird ◽  
Golam M. Newaz ◽  
...  
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Dissimilar Materials ◽  
Optical Microscope ◽  
Mechanical Analysis ◽  
Maximum Temperature ◽  
Stress Profile ◽  
Residual Stress Profile ◽  
Thermal Mechanical Analysis

Detailed analysis of a residual stress profile due to laser microjoining of two dissimilar biocompatible materials, polyimide (PI) and titanium (Ti), is vital for the long-term application of bio-implants. In this work, a comprehensive three-dimensional (3D) transient model for sequentially coupled thermal/mechanical analysis of transmission laser (laser beam with wavelength of 1100 nm and diameter of 0.2 mm) microjoining of two dissimilar materials has been developed by using the finite element code ABAQUS, along with a moving Gaussian laser heat source. First the model has been used to optimize the laser parameters like laser traveling speed and power to obtain good bonding (burnout temperature of PI>maximum temperature of PI achieved during heating>melting temperature of PI) and a good combination has been found to be 100 mm/min and 3.14 W for a joint-length of 6.5 mm as supported by the experiment. The developed computational model has been observed to generate a bonding zone that is similar in width (0.33 mm) to the bond width of the Ti/PI joint observed experimentally by an optical microscope. The maximum temperatures measured at three locations by thermocouples have also been found to be similar to those observed computationally. After these verifications, the residual stress profile of the laser microjoint (100 mm/min and 3.14 W) has been calculated using the developed model with the system cooling down to room temperature. The residual stress profiles on the PI surface have shown low value near the centerline of the laser travel, increased to higher values at about 165 μm from the centerline symmetrically at both sides, and to the contrary, have shown higher values near the centerline on the Ti surface. Maximum residual stresses on both the Ti and PI surfaces are obtained at the end of laser travel, and are in the orders of the yield stresses of the respective materials. It has been explained that the patterned accumulation of residual stresses is due to the thermal expansion and contraction mismatches between the dissimilar materials at the opposite sides of the bond along with the melting and softening of PI during the joining process.

scholarly journals On the Accuracy of Finite Element Models Predicting Residual Stresses in Quenched Stainless Steel

Metals ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 1308 ◽  
Author(s):  
Israel Medina-Juárez ◽  
Jeferson Araujo de Oliveira ◽  
Richard J. Moat ◽  
Francisco Alfredo García-Pastor
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stainless Steel ◽  
Residual Stresses ◽  
Contour Method ◽  
Stress Profile ◽  
304L Stainless Steel ◽  
Fem Model ◽  
Residual Stress Profile ◽  
Industry Applications

Prediction of residual stress profiles after quenching is important for a range of industry applications. Finite element method (FEM) models have the capability of simulate the cooling and stress evolution during quenching; however, they are very dependent on the heat transfer coefficient (HTC) imposed on the surface. In this paper, an analysis of the HTC effect on the accuracy of the residual stress profile after quenching a 304L stainless steel Jominy sample was conducted. The FEM model was validated in its thermal accuracy using thermocouples and the residual stress profile was measured using the contour method. The results show that a thermally validated FEM model may yield results which overestimate the tensile residual stress and underestimates the compressive residual stress maxima while accurately calculating the maxima positions from the quenched edge. The FEM model accuracy was not improved by modifying the HTC or by using a different thermal expansion coefficient. The results are discussed in terms of the effect of plasticity due to twinning in the residual stresses calculated by the FEM model.

Sign in / Sign up

Export Citation Format

Share Document