The Influence of an Arrangement of an Array of Semi-Submersible Type FOWTs to Their Hydrodynamic Responses

2017 ◽  
Author(s):  
Motohiko Murai ◽  
Kensaku Takahashi
Keyword(s):  
Wind Turbine ◽  
Wind Farm ◽  
Offshore Wind ◽  
Floating Wind Turbine ◽  
Wind Turbine System ◽  
Hydrodynamic Response ◽  
Electric Generation ◽  
Greenhouse Effect Gas ◽  
Sea Area ◽  
Land Space

The progress of the global warming is one of our key issue should be overcome in the 21st century. We should balance the energy consumption and reduction of exhausting greenhouse effect gas. The wind energy is expected as one of the key technology for utilizing renewable energy. It is said that as for the efficiency of the electric generation, it is better the wider wind farm with larger wind mill. But, as the land space for the extensive wind farm is quite limited, it will be a candidate how to use the vast ocean space for human activity. So, the construction of an offshore wind farm is one of the solution now. To extend the wind farm widely in the ocean the floating wind turbine system becomes an essential technology. Under such background, there are many researches on the floating wind turbine in waves and in wind. And hydrodynamic response of them in waves is one of the major topics. Many of the researches on the hydrodynamic response, however, deal with the motion of a single floating wind turbine. This report deals with the hydrodynamic response of a wind farm which is consisted of semi-submersible wind turbines. In addition, the investigation of how does the arrangement of the array impact on the hydrodynamic response including the motion of the nacelle is also reported. In the last the example of the change of the expected efficiency of the generator by change of the array arrangement in each sea area around Japan are shown.

Study on the Dynamic Response for Floating Foundation of Offshore Wind Turbine

2011 ◽  
Author(s):  
Yougang Tang ◽  
Jun Hu ◽  
Liqin Liu
Keyword(s):  
Wind Turbine ◽  
Wind Farm ◽  
Dynamic Responses ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Wave Load ◽  
Mooring Lines ◽  
Floating Foundation ◽  
Wind Turbine System ◽  
Sea Area

The wind resources for ocean power generation are mostly distributed in sea areas with the distance of 5–50km from coastline, whose water depth are generally over 20m. To improve ocean power output and economic benefit of offshore wind farm, it is necessary to choose floating foundation for offshore wind turbine. According to the basic data of a 600kW wind turbine with a horizontal shaft, the tower, semi-submersible foundation and mooring system are designed in the 60-meter-deep sea area. Precise finite element models of the floating wind turbine system are established, including mooring lines, floating foundation, tower and wind turbine. Dynamic responses for the floating foundation of offshore wind turbine are investigated under wave load in frequency domain.

scholarly journals Dynamic Modeling of an Offshore Floating Wind Turbine for Application in the Mediterranean Sea

Energies ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 248
Author(s):  
Lorenzo Cottura ◽  
Riccardo Caradonna ◽  
Alberto Ghigo ◽  
Riccardo Novo ◽  
Giovanni Bracco ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Mediterranean Sea ◽  
Wind Farm ◽  
Reference Model ◽  
Wide Spectrum ◽  
Wind Farms ◽  
Offshore Wind ◽  
Floating Wind Turbine ◽  
The Mediterranean ◽  
Offshore Floating Wind Turbine

Wind power is emerging as one of the most sustainable and low-cost options for energy production. Far-offshore floating wind turbines are attractive in view of exploiting high wind availability sites while minimizing environmental and landscape impact. In the last few years, some offshore floating wind farms were deployed in Northern Europe for technology validation, with very promising results. At present time, however, no offshore wind farm installations have been developed in the Mediterranean Sea. The aim of this work is to comprehensively model an offshore floating wind turbine and examine the behavior resulting from a wide spectrum of sea and wind states typical of the Mediterranean Sea. The flexible and accessible in-house model developed for this purpose is compared with the reference model FAST v8.16 for verifying its reliability. Then, a simulation campaign is carried out to estimate the wind turbine LCOE (Levelized Cost of Energy). Based on this, the best substructure is chosen and the convenience of the investment is evaluated.

Experimental Study for SPAR Type Floating Offshore Wind Turbine With Blade-Pitch Control

2013 ◽  
Author(s):  
Toshiki Chujo ◽  
Yoshimasa Minami ◽  
Tadashi Nimura ◽  
Shigesuke Ishida
Keyword(s):  
Wind Turbine ◽  
Wind Farm ◽  
Offshore Wind ◽  
Scale Model ◽  
Offshore Wind Turbine ◽  
Experimental Proof ◽  
Pitch Control ◽  
Model Experiments ◽  
North Eastern ◽  
North Eastern Part

The experimental proof of the floating wind turbine has been started off Goto Islands in Japan. Furthermore, the project of floating wind farm is afoot off Fukushima Prof. in north eastern part of Japan. It is essential for realization of the floating wind farm to comprehend its safety, electric generating property and motion in waves and wind. The scale model experiments are effective to catch the characteristic of floating wind turbines. Authors have mainly carried out scale model experiments with wind turbine models on SPAR buoy type floaters. The wind turbine models have blade-pitch control mechanism and authors focused attention on the effect of blade-pitch control on both the motion of floater and fluctuation of rotor speed. In this paper, the results of scale model experiments are discussed from the aspect of motion of floater and the effect of blade-pitch control.

scholarly journals Improving the Strategy of Maintaining Offshore Wind Turbines through Petri Net Modelling

2021 ◽  
Vol 11 (2) ◽  
pp. 574
Author(s):  
Rundong Yan ◽  
Sarah Dunnett
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Petri Net ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Maintenance Costs ◽  
Offshore Wind Turbines ◽  
Major Repair ◽  
Wind Turbine System ◽  
Periodic Maintenance

In order to improve the operation and maintenance (O&M) of offshore wind turbines, a new Petri net (PN)-based offshore wind turbine maintenance model is developed in this paper to simulate the O&M activities in an offshore wind farm. With the aid of the PN model developed, three new potential wind turbine maintenance strategies are studied. They are (1) carrying out periodic maintenance of the wind turbine components at different frequencies according to their specific reliability features; (2) conducting a full inspection of the entire wind turbine system following a major repair; and (3) equipping the wind turbine with a condition monitoring system (CMS) that has powerful fault detection capability. From the research results, it is found that periodic maintenance is essential, but in order to ensure that the turbine is operated economically, this maintenance needs to be carried out at an optimal frequency. Conducting a full inspection of the entire wind turbine system following a major repair enables efficient utilisation of the maintenance resources. If periodic maintenance is performed infrequently, this measure leads to less unexpected shutdowns, lower downtime, and lower maintenance costs. It has been shown that to install the wind turbine with a CMS is helpful to relieve the burden of periodic maintenance. Moreover, the higher the quality of the CMS, the more the downtime and maintenance costs can be reduced. However, the cost of the CMS needs to be considered, as a high cost may make the operation of the offshore wind turbine uneconomical.

Fatigue Life Analysis of Offshore Wind Turbine Support Structures in an Offshore Wind Farm

2018 ◽  
Author(s):  
Bryan Nelson ◽  
Yann Quéméner
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Wind Farm ◽  
The Body ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Analysis Tool ◽  
Support Structures ◽  
Offshore Wind Farm ◽  
Actuator Disk

This study evaluated, by time-domain simulations, the fatigue lives of several jacket support structures for 4 MW wind turbines distributed throughout an offshore wind farm off Taiwan’s west coast. An in-house RANS-based wind farm analysis tool, WiFa3D, has been developed to determine the effects of the wind turbine wake behaviour on the flow fields through wind farm clusters. To reduce computational cost, WiFa3D employs actuator disk models to simulate the body forces imposed on the flow field by the target wind turbines, where the actuator disk is defined by the swept region of the rotor in space, and a body force distribution representing the aerodynamic characteristics of the rotor is assigned within this virtual disk. Simulations were performed for a range of environmental conditions, which were then combined with preliminary site survey metocean data to produce a long-term statistical environment. The short-term environmental loads on the wind turbine rotors were calculated by an unsteady blade element momentum (BEM) model of the target 4 MW wind turbines. The fatigue assessment of the jacket support structure was then conducted by applying the Rainflow Counting scheme on the hot spot stresses variations, as read-out from Finite Element results, and by employing appropriate SN curves. The fatigue lives of several wind turbine support structures taken at various locations in the wind farm showed significant variations with the preliminary design condition that assumed a single wind turbine without wake disturbance from other units.

Comparison of Spar and Semisubmersible Floater Concepts of Offshore Wind Turbines Using Long-Term Analysis

2015 ◽  
Vol 137 (6) ◽  
Author(s):  
Hasan Bagbanci ◽  
D. Karmakar ◽  
C. Guedes Soares
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Transfer Functions ◽  
Probability Distributions ◽  
Offshore Wind ◽  
Short Term ◽  
Offshore Wind Turbines ◽  
Floating Wind Turbine ◽  
Offshore Floating Wind Turbine

The long-term probability distributions of a spar-type and a semisubmersible-type offshore floating wind turbine response are calculated for surge, heave, and pitch motions along with the side-to-side, fore–aft, and yaw tower base bending moments. The transfer functions for surge, heave, and pitch motions for both spar-type and semisubmersible-type floaters are obtained using the fast code and the results are also compared with the results obtained in an experimental study. The long-term predictions of the most probable maximum values of motion amplitudes are used for design purposes, so as to guarantee the safety of the floating wind turbines against overturning in high waves and wind speed. The long-term distribution is carried out using North Atlantic wave data and the short-term floating wind turbine responses are represented using Rayleigh distributions. The transfer functions are used in the procedure to calculate the variances of the short-term responses. The results obtained for both spar-type and semisubmersible-type offshore floating wind turbine are compared, and the study will be helpful in the assessments of the long-term availability and economic performance of the spar-type and semisubmersible-type offshore floating wind turbine.

DNV GL Standard for Floating Wind Turbines

2018 ◽  
Author(s):  
Anne Lene Haukanes Hopstad ◽  
Kimon Argyriadis ◽  
Andreas Manjock ◽  
Jarett Goldsmith ◽  
Knut O. Ronold
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Technical Specification ◽  
Oil And Gas Industry ◽  
Offshore Wind ◽  
Floating Structures ◽  
Service Specification ◽  
Technical Requirements ◽  
Floating Wind Turbine ◽  
Damage Stability

The first issue of the DNV Offshore Standard, DNV-OS-J103 Design of Floating Wind Turbine Structures, was published in June 2013. The standard was based on a joint industry effort with representatives from manufacturers, developers, utility companies and certifying bodies from Europe, Asia and the US. The standard represented a condensation of all relevant requirements for floaters in existing DNV standards for the offshore oil and gas industry which were considered relevant also for offshore floating structures for support of wind turbines, supplemented by necessary adaptation to the wind turbine application. The development of the standard capitalized much on experience from development projects going on at the time, in particular the Hywind spar off the coast of western Norway, the WindFloat off the coast of Portugal and the Pelastar TLP concept. In July 2018, DNV GL published a revision of DNV-OS-J103 as a part of the harmonization of the DNV GL codes for the wind turbine industry after the merger between Det Norske Veritas (DNV) and Germanischer Lloyd (GL) in the fall of 2013. The standard was re-issued as DNVGL-ST-0119 Floating wind turbine structures. This new revision reflects the experience gained after the first issue in 2013 as well as the current trends within the industry. Since 2013, numerous guidelines addressing the design of floating structures for offshore wind turbines have been published by various certifying bodies, and an IEC technical specification on the subject is under way. In addition, several prototypes have been installed and the first small array of floating wind turbines, Hywind Scotland pilot park, are currently in operation. The most important updates in the revision of the standard include formulation of floater-specific load cases, requirements to be fulfilled to support the exemption for design of unmanned floaters with damage stability, and replacement of current consequence-class based requirements for design fatigue factors with low-consequence based factors dependent on the accessibility for inspection and repair, the aim being a safety level against fatigue similar to that which is currently targeted for bottom-fixed structures. Other topics which have been considered in the revision are the floater motion control system and its possible integration with the control and protection system for the wind turbine, the issue of how to deal with slack in tendons in the station keeping system, corrosion, anchor design and power cable design. In parallel to the revision of the standard, a new service specification for certification of floating wind turbines has been developed by DNV GL, identified as DNVGL-SE-0422 Certification of floating wind turbines. For technical requirements, the service specification refers to the revised standard, DNVGL-ST-0119. The technical paper summarizes the updates and changes in the revised standard, in addition to the content of the new service specification.

Sign in / Sign up

Export Citation Format

Share Document