Large-Scale Experiments of Wave-Overtopping Loads on Walls: Layer Thicknesses and Velocities

2018 ◽  
Author(s):  
Lorenzo Cappietti ◽  
Irene Simonetti ◽  
Andrea Esposito ◽  
Maximilian Streicher ◽  
Andreas Kortenhaus ◽  
...  
Keyword(s):  
Large Scale ◽  
Scale Validation ◽  
Irregular Waves ◽  
Scale Model ◽  
Small Scale ◽  
Wave Loads ◽  
Wave Overtopping ◽  
Large Scale Model ◽  
Vertical Walls ◽  
Set Up

Wave-Overtopping loads on vertical walls, such as those located on top of a dike, have been investigated in several small-scale experiments in the past. A large-scale validation for a mild foreshore situation is still missing. Hence the WALOWA (WAve LOads on WAlls) experimental campaign was carried out to address this topic. This paper, first presents a description of the large-scale model, the measurement set-up and the experimental methodologies, then it focuses on the layer thicknesses and velocities of the flows created on the promenade by the wave overtopping. A set of resistive wave gauges, ultrasonic distance sensors and velocimeters have been used to conduct these measurements. Preliminary data analysis and results, related to a 1000 irregular waves long test, are discussed. The momentum flux of these flows is studied and its implications, for the wave-overtopping loads acting on the vertical walls, are highlighted.

scholarly journals EXTERNAL AND INTERNAL WAVE SET-UP AT POROUS PBA REVETMENTS ON A SAND FOUNDATION

2012 ◽  
Vol 1 (33) ◽  
pp. 27
Author(s):  
Gisa Foyer ◽  
Hocine Oumeraci
Keyword(s):  
Large Scale ◽  
Wave Length ◽  
Irregular Waves ◽  
Scale Model ◽  
Large Scale Model ◽  
Internal Set ◽  
Deep Water Wave ◽  
Set Up ◽  
The Stability ◽  
Almost All

Wave set-up is generally considered for the stability analysis of beaches, but not or not explicitly for the design of revetments. Based on large-scale model results with regular and irregular waves, it is shown in this paper that this is not justified. For this purpose, the wave set-up on a porous bonded revetment and the related internal set-up in the sand foundation below the revetment are analysed for different breaker types. The results particularly show that (i) considerable set-up values are obtained for almost all breaker types, (ii) a good correlation exists with the deep water wave length for both external and internal set-up and (iii) the internal set-up is significantly affected by the wave set-up on the slope. Empirical formulae for the prediction of the external and internal set-up are also proposed for both regular and irregular waves.

RANCANG BANGUN PERANGKAT EKSPERIMENTASI PROSES PIROLISIS BIOMASA GELOMBANG MIKRO

2013 ◽  
Vol 14 (2) ◽  
Author(s):  
Noor Fachrizal
Keyword(s):  
Large Scale ◽  
Continuous Model ◽  
Biomass Energy ◽  
Scale Model ◽  
Small Scale ◽  
Laboratory Apparatus ◽  
Liquid Form ◽  
Large Scale Model ◽  
Bio Oil ◽  
Pyrolysis Of Biomass

Biomass such as agriculture waste and urban waste are enormous potency as energy resources instead of enviromental problem. organic waste can be converted into energy in the form of liquid fuel, solid, and syngas by using of pyrolysis technique. Pyrolysis process can yield higher liquid form when the process can be drifted into fast and flash response. It can be solved by using microwave heating method. This research is started from developing an experimentation laboratory apparatus of microwave-assisted pyrolysis of biomass energy conversion system, and conducting preliminary experiments for gaining the proof that this method can be established for driving the process properly and safely. Modifying commercial oven into laboratory apparatus has been done, it works safely, and initial experiments have been carried out, process yields bio-oil and charcoal shortly, several parameters are achieved. Some further experiments are still needed for more detail parameters. Theresults may be used to design small-scale continuous model of productionsystem, which then can be developed into large-scale model that applicable for comercial use.

Large scale model test investigation on wave run-up in irregular waves at slender piles

2013 ◽  
Vol 72 ◽  
pp. 69-79 ◽  
Author(s):  
J. Ramirez ◽  
P. Frigaard ◽  
T. Lykke Andersen ◽  
L. de Vos
Keyword(s):  
Model Test ◽  
Large Scale ◽  
Irregular Waves ◽  
Scale Model ◽  
Large Scale Model ◽  
Test Investigation ◽  
Run Up

The Effects of Scaling and Model Complexity in Simulating the Transport of Inorganic Micropollutants in a Lowland River Reach

2006 ◽  
Vol 41 (1) ◽  
pp. 24-36 ◽  
Author(s):  
Karl-Erich Lindenschmidt ◽  
René Wodrich ◽  
Cornelia Hesse
Keyword(s):  
Large Scale ◽  
Transport Model ◽  
Transport Processes ◽  
Model Complexity ◽  
Scale Model ◽  
Small Scale ◽  
Quality Model ◽  
Large Scale Model ◽  
Iron And Zinc ◽  
Physical And Chemical

Abstract A hypothesis stating that more complex descriptions of processes in models simulate reality better (less error) but with more unreliable predictability (more sensitivity) is tested using a river water quality model. This hypothesis was extended stating that applying the model on a domain of smaller scale requires greater complexity to capture the same accuracy as in large-scale model applications which, however, leads to increased model sensitivity. The sediment and pollutant transport model TOXI, a module in the WASP5 package, was applied to two case studies of different scale: a 90-km course of the 5th order (sensu Strahler 1952) lower Saale river, Germany (large scale), and the lock-and-weir system at Calbe (small scale) situated on the same river course. A sensitivity analysis of several parameters relating to the physical and chemical transport processes of suspended solids, chloride, arsenic, iron and zinc shows that the coefficient, which partitions the total heavy metal mass into its dissolved and sorbed fraction, is a very sensitive parameter. Hence, the complexity of the sorptive process was varied to test the hypotheses.

scholarly journals HYDRAULIC PERFORMANCE OF ELASTOMERIC BONDED PERMEABLE REVETMENTS AND SUBSOIL RESPONSE TO WAVE LOADS

2011 ◽  
Vol 1 (32) ◽  
pp. 22
Author(s):  
Hocine Oumeraci ◽  
Tijl Staal ◽  
Saskia Pfoertner ◽  
Matthias Kudella ◽  
Stefan Schimmels ◽  
...  
Keyword(s):  
Large Scale ◽  
Hydraulic Performance ◽  
Soil Liquefaction ◽  
Scale Model ◽  
Research Centre ◽  
Wave Loads ◽  
Large Scale Model ◽  
Wide Range ◽  
Physically Based ◽  
Run Up

Elastomeric bonded permeable revetments, also called PBA (Polyurethane bonded aggregate) revetments, are highly porous structures made of mineral aggregates (e.g. crushed stones) which are durably and elastically bonded by polyurethane (PU). Despite their numerous advantages as compared to conventional revetments and the large experience available from more than 25 pilot projects, physically-based design formulae to predict their hydraulic performance, wave loading and response are still lacking. Therefore, the present study aims at improving the understanding of the processes involved in the interaction between wave, revetment and foundation, based on large-scale model tests performed in the Coastal Research Centre (FZK), Hannover/Germany, and to provide prediction formulae/diagrams. This paper is focused on the prediction of the hydraulic performance (wave reflection, wave run-up and run-down) and the response of the sand core (pore pressure and effective stress) beneath the revetment for a wide range of wave conditions, including the analysis of an observed failure due to transient soil liquefaction.

scholarly journals LARGE SCALE MODEL TESTS OF PLACED STONE BREAKWATERS

1976 ◽  
Vol 1 (15) ◽  
pp. 147 ◽  
Author(s):  
Charles K. Sollitt ◽  
Donald H. Debok
Keyword(s):  
Large Scale ◽  
Scale Model ◽  
Small Scale ◽  
Stable Model ◽  
Model Studies ◽  
Drag Forces ◽  
Port Facilities ◽  
Large Scale Model ◽  
Wave Heights ◽  
Water Depths

Large scale model studies reveal that Reynolds scaling can affect the apparent stability and wave modifying properties of layered breakwater structures. Results of a study for a breakwater configuration designed to protect offshore power and port facilities in water depths to 60 feet are presented and discussed. The armor layer of this structure is formed from quarried rock of irregular rectangular parallelepiped shape, individually placed perpendicular to 1:2 seaward slope and crest. The resulting armor layer is relatively smooth, densely packed and very stable. Model studies of similar configurations were studied at 1:10, 1:20 and 1:100 scale ratios. Stability, runup, rundown and reflection were measured for a variety of water depths, wave heights and periods. Analysis of the large scale test results establish that the placed stone armor is approximately as stable as dolos armor units. Runup, rundown and reflection respond similar to rough, impermeable slopes. Comparison of large and small scale results demonstrate that relative increases in drag forces at lower Reynolds numbers decrease stability and runup in small scale models.

VIOLENT WAVE OVERTOPPING ON VERTICAL AND INCLINED WALLS: LARGE SCALE MODEL TESTS

2005 ◽  
Author(s):  
JOACHIM GRÜNE ◽  
ZEYA WANG ◽  
GEOFFREY BULLOCK ◽  
CHARLOTTE OBHRAI
Keyword(s):  
Large Scale ◽  
Model Tests ◽  
Scale Model ◽  
Wave Overtopping ◽  
Large Scale Model

Small-Scale Models for Testing Masonry Structures

2010 ◽  
Vol 133-134 ◽  
pp. 497-502 ◽  
Author(s):  
Alvaro Quinonez ◽  
Jennifer Zessin ◽  
Aissata Nutzel ◽  
John Ochsendorf
Keyword(s):  
Large Scale ◽  
Low Cost ◽  
Three Dimensional ◽  
Model Testing ◽  
Scale Model ◽  
Small Scale ◽  
Material Strength ◽  
Masonry Structures ◽  
Scale Models ◽  
Set Up

Experiments may be used to verify numerical and analytical results, but large-scale model testing is associated with high costs and lengthy set-up times. In contrast, small-scale model testing is inexpensive, non-invasive, and easy to replicate over several trials. This paper proposes a new method of masonry model generation using three-dimensional printing technology. Small-scale models are created as an assemblage of individual blocks representing the original structure’s geometry and stereotomy. Two model domes are tested to collapse due to outward support displacements, and experimental data from these tests is compared with analytical predictions. Results of these experiments provide a strong understanding of the mechanics of actual masonry structures and can be used to demonstrate the structural capacity of masonry structures with extensive cracking. Challenges for this work, such as imperfections in the model geometry and construction problems, are also addressed. This experimental method can provide a low-cost alternative for the collapse analysis of complex masonry structures, the safety of which depends primarily on stability rather than material strength.

Small and Large Scale Experimental Investigations of Wave Loads on a Slender Pile Within Closely Spaced Neighbouring Piles

2014 ◽  
Author(s):  
Lisham Bonakdar ◽  
Hocine Oumeraci
Keyword(s):  
Laboratory Tests ◽  
Large Scale ◽  
Model Tests ◽  
Scale Model ◽  
Research Centre ◽  
Experimental Investigations ◽  
Small Scale ◽  
Wave Loads ◽  
Large Wave ◽  
Wave Flume

Wave loads on a slender pile within a group of piles are studied by means of (i) large-scale laboratory tests carried out in the Large Wave Flume (GWK) of the Coastal Research Centre (FZK) in Hannover, and (ii) small scale experiments performed in 2 m-wide wave flume of Leichtweiss-Institute for Hydraulic Engineering and Water Resources (LWI), in Braunschweig, Germany. The small scale model tests (LWI) were scaled down (1:6.5) by Froude law from the large scale model tests (GWK). Scale and model effects are examined by comparing the results of small and large scale laboratory tests.

Wave Loads of Slender Marine Cylinders Depending on Interaction Effects of Adjacent Cylinders

2006 ◽  
Author(s):  
Uwe Sparboom ◽  
Hocine Oumeraci
Keyword(s):  
Large Scale ◽  
Research Programme ◽  
Basic Research ◽  
Irregular Waves ◽  
Research Centre ◽  
Wave Loads ◽  
Freak Waves ◽  
First Results ◽  
Set Up ◽  
Coastal Research

Within a basic research programme at the Coastal Research Centre (FZK) in Hannover large-scale wave experiments were performed with single vertical and inclined Cylinders (Oumeraci, 2004). Additionally, cylinder groups were investigated with special reference to shelter and amplification effects depending on cylinder spacing. Nonbreaking regular and irregular waves as well as breaking freak waves were generated. The test set-up and some first results of the experiments looking to the maximum wave loads are reported in the paper.

Sign in / Sign up

Export Citation Format

Share Document