Study on Residual-Stress Redistributions During the Process of Manufacture of a Vessel Penetration Set-On Joint

2009 ◽  
Author(s):  
Nobuyoshi Yanagida ◽  
Kazuo Ogawa ◽  
Koichi Saito ◽  
Ed Kingston
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Alloy Steel ◽  
Steel Plate ◽  
Three Dimensional ◽  
Hole Drilling ◽  
Low Alloy Steel ◽  
Butt Weld ◽  
Control Rod ◽  
Inner Surface

The stress-redistribution phenomenon in a vessel penetration set-on joint due to post-weld heat treatment (PWHT) was studied using finite element (FE) analyses and mocked-up experiments. The mocked-up consisted of a nickel-based alloy (NCF600) tube welded onto an alloy-82 cladded, low-alloy steel plate (SQV2A) using an alloy-182 butt weld. The angle of the tube to the plate surface was 45 degrees, simulating a side hill, a control rod drive (CRD), and a stub-tube nozzle attachment used in boiling-water reactor (BWR) plants. PWHT at a temperature of 625 °C was conducted after welding and then the inner surface of the tube was machined. Three-dimensional FE modeling was performed to simulate the cladding, the butt weld, the PWHT, and the inner-surface machining of the tube. Thermal elasto-plastic and thermal elasto-plastic creep analyses were conducted to simulate the process of residual-stress build up and its redistribution by PWHT. To validate the FE analysis, the residual stresses in the mocked-up specimen were experimentally measured using the deep-hole-drilling (DHD) and sectioning methods. The analytical and experimental results revealed that residual-stress redistributions in the mocked-up specimen were different in circumferential positions. High-residual stresses in the low-alloy steel plate were particularly mitigated during the PWHT. The stress relief in the low-alloy steel plate primarily controlled the global stress balance between the cladding, the weld metal, and the stub tube.

scholarly journals Influence of carbonitriding conditions on phase composition and residual stresses for 20MnCr5 low alloy steel

2021 ◽  
Vol 47 (2) ◽  
pp. 790-799
Author(s):  
Richard J Katemi ◽  
Jeremy Epp
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Alloy Steel ◽  
Retained Austenite ◽  
Case Depth ◽  
Martensite Phase ◽  
Stress Distributions ◽  
Low Alloy Steel ◽  
The Core ◽  
Core Hardness

This paper reports an investigation of the influence of carbonitriding conditions for 20MnCr5 low alloy steel. Three gaseous carbonitriding conditions were investigated based on different carbon and nitrogen potentials to attain varying levels of carbon between 0.62 and 0.93% mass, whereas for nitrogen between 0.19 and 0.26% mass at the surface. Analysis of retained austenite and residual stress distributions was conducted using X-ray diffraction technique. The effective case depth varied between 900 and 1200 µm. The case microstructures were characterized by varying proportions of retained austenite and martensite, while the core contained essentially bainitic microstructures. The maximum amount of retained austenite which occurred at a depth of 50 µm from the subsurface ranged between 30 and 70% mass and significantly influenced the level of surface micro-hardness whereas the core hardness remaining relatively constant at 450 HV1. High values of residual stresses in martensite phase were observed. The signs, magnitudes, distributions and location of maximum compressive residual stresses were highly influenced by the maximum fraction of retained austenite. Retained austenite of 30%, 50% and 70% mass at the surface lead to peak compressive residue stresses of -280, -227, and -202 MPa at depths of 555, 704, and 890 μm, respectively. Keywords: Carbonitriding, retained austenite, martensite, residual stress, XRD.

Residual Stress Prediction and Relaxation in Welded Tubular Joints under Constant Cyclic Loading

2006 ◽  
Vol 524-525 ◽  
pp. 323-330 ◽  
Author(s):  
Zuheir Barsoum
Keyword(s):  
Thermal Analysis ◽  
Residual Stress ◽  
Residual Stresses ◽  
Fatigue Testing ◽  
Three Dimensional ◽  
Hole Drilling ◽  
Moving Heat Source ◽  
Tubular Joints ◽  
Stress Prediction ◽  
Tubular Joint

In this paper three-dimensional welding simulations were carried out in FE software ANSYS in order to predict transient temperatures and the residual stresses in a three pass welded tubular joints. The thermal analysis and the moving heat source were verified with temperature measurements and the computed residual stresses were verified with hole drilling measurements. Then residual stress relaxation analyses were carried out on the tubular structure, with similar load cases as in earlier fatigue testing on the same tubular joint structures.

Effect of the interpass temperature on the predicted residual stress distributions in a multipass welded piping branch junction

2008 ◽  
Vol 43 (2) ◽  
pp. 109-119 ◽  
Author(s):  
W Jiang ◽  
K Yahiaoui
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Cross Sections ◽  
Branch Pipe ◽  
Three Dimensional ◽  
Weld Line ◽  
Element Model ◽  
Stress Distributions ◽  
Inner Surface ◽  
Interpass Temperature

A sequentially coupled three‐dimensional thermomechanical finite element model has been developed to predict residual stress distributions in a multipass welded piping branch junction. The residual stresses at the branch and run pipe cross‐sections, as well as along the circumferential weldlines on the outer surfaces of both the run and the branch pipes and on the inner surface of the branch pipe, are predicted. Three levels of interpass temperature have been selected to investigate their effect on the peak residual stresses. It is revealed that the interpass temperature has a significant effect on the residual stresses. As the interpass temperature is increased, both the peak hoop and the axial residual stresses at the run and branch cross‐sections decrease. The peak normal stresses along the circumferential weldline on the outer surface of the run pipes are also reduced. However, increasing the interpass temperature had a negligible effect on the peak tangential residual stresses along the circumferential weld line on the inner surface of the branch pipe. The results presented and the modelling technique described in the current study can be used towards formulating a recommendation to optimize residual stress profiles in multipass welded complex geometries through better interpass temperature control.

scholarly journals Investigations of Residual Stress Distributions in Retained Austenite and Martensite after Carbonitriding of a Low Alloy Steel

2014 ◽  
Vol 996 ◽  
pp. 550-555
Author(s):  
Richard J. Katemi ◽  
Jeremy Epp ◽  
Franz Hoffmann ◽  
Matthias Steinbacher
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Alloy Steel ◽  
Retained Austenite ◽  
Stress Distributions ◽  
Low Alloy Steel ◽  
X Ray Diffraction ◽  
Carbon And Nitrogen ◽  
Stress States ◽  
Nitrogen Contents

Specimens of low alloy steel were carbonitrided under different conditions to attain varying levels of carbon and nitrogen contents. The residual stress depth distribution was evaluated in martensite and retained austenite by X-ray diffraction. Beside standard evaluations, triaxial residual stress states with σ33≠0 in both phases were also considered. High values of residual stresses in both phases were observed. The sign, magnitude and location of maximum compressive residual stresses were greatly influenced by the level of carbon and nitrogen contents.

Residual Stress Analysis of Bead Welded Low Alloy Steel Plate Specimens Subjected to Post Weld Heat Treatment

2011 ◽  
Author(s):  
Nobuyoshi Yanagida ◽  
Koichi Saito
Keyword(s):  
Heat Treatment ◽  
Residual Stress ◽  
Phase Transformation ◽  
Stress Analysis ◽  
Alloy Steel ◽  
Steel Plate ◽  
Post Weld Heat Treatment ◽  
Welding Residual Stress ◽  
Low Alloy Steel ◽  
Residual Stress Analysis

We developed a residual stress analysis method for bead welded low alloy steel JIS SQV2A (equivalent to ASTM A533B cl. 1) plates subjected to post weld heat treatment (PWHT). Two specimens were fabricated; each was a bead welded low alloy steel plate. One was in the as-welded condition (as-welded specimen) and the other was subjected to PWHT at 625°C (PWHT specimen). Strain gauges were used to measure the distributions of the residual stress in these specimens. The measurement data showed that the longitudinal stress at the center of a bead was 0 MPa and that in the heat-affected zone was 100 MPa. The transverse stress at the center of a bead was 200 MPa in the as-welded specimen. The absolute residual stress was decreased to less than 50 MPa for the PWHT specimen. We conducted finite element analyses to predict the distributions of welding residual stress in these specimens. The amount of phase transformation strain in low alloy steel was taken into account in the welding residual stress analysis, and creep strain was taken into account in the stress mitigation analysis. The results from the analyses agree well with the experimental results. These findings prove that welding residual stress can be simulated during a thermal elastic plastic (TEP) analysis by conducting a phase transformation and taking the generation of creep strain in the PWHT samples into consideration can be used to simulate that stress mitigation.

scholarly journals Influence of Tempering and Cryogenic Treatment on Retained Austenite and Residual Stresses in Carbonitrided 18CrNiMo7-6 Low Alloy Steel

2019 ◽  
Vol 38 (1) ◽  
pp. 71-82
Author(s):  
Richard J. Katemi ◽  
Jeremy Epp
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Alloy Steel ◽  
Retained Austenite ◽  
Cryogenic Treatment ◽  
Thermal Stabilization ◽  
Gas Analysis ◽  
Low Alloy Steel ◽  
Mass Percent ◽  
Carbon And Nitrogen Content

This work investigated the influence of tempering conditions coupled with cryogenic treatment on thermal stabilization of retained austenite and residual stress distributions in carbonitrided 18CrNiMo76 low alloy steel samples. The carbonitriding conditions were set to enable attaining surface carbon and nitrogen content of 0.87 and 0.34 mass.-percent respectively. After carbonitriding, some of the samples were subjected to varying tempering conditions followed by cryogenic treatment at -120 °C using nitrogen gas. Analysis of both retained austenite and residual stresses was conducted using X-ray diffraction. In the as-quenched state, carbonitrided samples contained 52 mass.-percent. Samples that were directly subjected to the cryogenic treatment after quenching retained only about 20 mass.-percent of austenite. Samples subjected to variant tempering conditions coupled with cryogenic treatment retained at least 30 masses.-percent of austenite. A thermal stabilization of retained austenite which increases with increasing temperature was identified. On tempering at 240°C for 14 hours retained austenite becomes unstable and decomposes to bainite leading to the low initial amount of retained austenite before cryogenic treatment. It can be concluded that the tempering process coupled with cryogenic treatment leads to an increasing hardness, to higher compressive residual stresses as well as to a shift of the location of maximum compressive residual stress toward the surface.

scholarly journals The Contour Method for Residual Stress Determination Applied to an AA6082-T6 Friction Stir Butt Weld

2011 ◽  
Vol 681 ◽  
pp. 177-181 ◽  
Author(s):  
Valentin Richter-Trummer ◽  
Pedro Miguel Guimarães Pires Moreira ◽  
João Ribeiro ◽  
Paulo Manuel Salgado Tavares de Castro
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Residual Stresses ◽  
Cross Section ◽  
Residual Stress Distribution ◽  
Contour Method ◽  
Friction Stir Weld ◽  
Hole Drilling ◽  
Butt Weld ◽  
Friction Stir

Residual stresses parallel to the welding direction on a cross-section of a 3 mm thick friction stir butt-welded aluminum alloy AA6082-T6 plate were determined using the contour method. A full contour map of longitudinal residual stresses on a weld cross section was determined in this way, revealing detailed information on the residual stress distribution in the inside of a friction stir weld, especially in the nugget zone. The typical M-shape, usually described for the residual stress distribution in friction stir welds, was found. The maximum residual stresses are below the yield strength of the material in the shoulder region and, outside of the welding region, low tensile and compressive residual stresses are responsible for the necessary stress equilibrium on the plane of interest. A comparison was made with the established incremental hole drilling technique on an equivalent plate for validation and good agreement of both techniques was obtained. The distribution, as well as the magnitude of the residual stresses measured by both techniques, is very similar, thus validating both the experimental and numerical procedures used for the contour method application, presented and discussed in the present paper.

scholarly journals Integral method coefficients for the ring-core technique to evaluate non-uniform residual stresses

2018 ◽  
Vol 53 (4) ◽  
pp. 210-224 ◽  
Author(s):  
Michele Barsanti ◽  
Marco Beghini ◽  
Ciro Santus ◽  
Alessio Benincasa ◽  
Lorenzo Bertelli
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Integral Method ◽  
Three Dimensional ◽  
Element Model ◽  
Hole Drilling ◽  
Stress Distributions ◽  
Three Dimensional Model ◽  
Small Depth ◽  
Ring Core

The ring-core technique allows for the determination of non-uniform residual stresses from the surface up to relatively higher depths as compared to the hole-drilling technique. The integral method, which is usually applied to hole-drilling, can also be used for elaborating the results of the ring-core test since these two experimental techniques share the axisymmetric geometry and the 0°–45°–90° layout of the strain gage rosette. The aim of this article is to provide accurate coefficients which can be used for evaluating the residual stress distribution by the ring-core integral method. The coefficients have been obtained by elaborating the results of a very refined plane harmonic axisymmetric finite element model and verified with an independent three-dimensional model. The coefficients for small depth steps were initially provided, and then the values for multiple integer step depths were also derived by manipulating the high-resolution coefficient matrices, thus showing how the present results can be practically used for obtaining the residual stresses according to different depth sequences, even non-uniform. This analysis also allowed the evaluation of the eccentricity effect which turned out to be negligible due to the symmetry of the problem. An applicative example was reported in which the input of the experimentally measured relaxed strains was elaborated with different depth resolutions, and the obtained residual stress distributions were compared.

Sign in / Sign up

Export Citation Format

Share Document