On the Effect of Heat Input and Interpass Temperature on the Performance of Inconel 625 Alloy Deposited Using Wire Arc Additive Manufacturing–Cold Metal Transfer Process

Relatively high heat input and heat accumulation are treated as critical challenges to affect the qualities and performances of components fabricated by wire arc additive manufacturing (WAAM). In this study, various heat inputs, namely 276, 552 and 828 J/mm, were performed to fabricate three thin-wall Inconel 625 structures by cold metal transfer (CMT)-based WAAM, respectively, and active interpass cooling was conducted to limit heat accumulation. The macrostructure, microstructure and mechanical properties of the produced components by CMT were investigated. It was found that the increased heat input can deteriorate surface roughness, and the size of dendrite arm spacing increases with increasing heat input, thus leading to the deterioration of mechanical properties. Lower heat input and application of active interpass cooling can be an effective method to refine microstructure and reduce anisotropy. This study enhances the understanding of interpass temperature control and the effectiveness of heat inputs for Inconel 625 alloy by WAAM. It also provides a valuable in situ process for microstructure and mechanical properties’ refinement of WAAM-fabricated alloys and the control of heat accumulation for the fabrication of large-sized structures for future practical applications.

Mechanical properties of wire and arc additively manufactured high-strength steel structures

Additive manufacturing with steel opens up new possibilities for the construction sector. Especially direct energy deposition processes like DED-arc, also known as wire arc additive manufacturing (WAAM), is capable of manufacturing large structures with a high degree of geometric freedom, which makes the process suitable for the manufacturing of force flow-optimized steel nodes and spaceframes. By the use of high strength steel, the manufacturing times can be reduced since less material needs to be deposited. To keep the advantages of the high strength steel, the effect of thermal cycling during WAAM needs to be understood, since it influences the phase transformation, the resulting microstructure, and hence the mechanical properties of the material. In this study, the influences of energy input, interpass temperature, and cooling rate were investigated by welding thin walled samples. From each sample, microsections were analyzed, and tensile test and Charpy-V specimens were extracted and tested. The specimens with an interpass temperature of 200 °C, low energy input and applied active cooling showed a tensile strength of ~ 860–900 MPa, a yield strength of 700–780 MPa, and an elongation at fracture between 17 and 22%. The results showed the formation of martensite for specimens with high interpass temperatures which led to low yield and high tensile strengths (Rp0.2 = 520–590 MPa, Rm = 780–940 MPa) for the specimens without active cooling. At low interpass temperatures, the increase of the energy input led to a decrease of the tensile and the yield strength while the elongation at fracture as well as the Charpy impact energy increased. The formation of upper bainite due to the higher energy input can be avoided by accelerated cooling while martensite caused by high interpass temperatures need to be counteracted by heat treatment.

Effect of Sigma Phase in Wire Arc Additive Manufacturing of Superduplex Stainless Steel

In the present study, the thermal program in wire and arc additive manufacturing has been varied in terms of heat input and interpass temperature. Three walls were completed with subsequent Charpy V impact toughness and crack-tip opening displacement fracture toughness, together with a detailed microstructure characterization using light microscopy and scanning and transmission electron microscopy. The results clearly demonstrate that the formation of sigma phase may deteriorate the toughness of superduplex components. Such formation may take place under prolonged cooling time, which may occur when subsequent passes are deposited with too high interpass temperatures. This transformation behavior may limit the productivity in additive manufacturing of such steels and care must be taken in selection of proper combination of arc energy and interpass temperature.

Effect of Thermal Management Approaches on Geometry and Productivity of Thin-Walled Structures of ER 5356 Built by Wire + Arc Additive Manufacturing

The present paper aimed at assessing the effect of two thermal management approaches on geometry and productivity of thin-walled structures built by Wire + Arc Additive Manufacturing (WAAM). Thin-walls of ER 5356 (Al5Mg) with different lengths and the same number of layers were deposited via the gas metal arc (GMA) process with the aid of an active cooling technique (near-immersion active cooling—NIAC) under a fixed set of deposition parameters. Then, the same experiment was performed with natural cooling (NC) in air. To characterize the thermal management approaches, the interpass temperature (i.e., the temperature at which subsequent layers are deposited) were monitored by a trailing/leading infrared pyrometer during the deposition time. Finally, thin walls with a fixed length were deposited using the NC and NIAC approaches with equivalent interpass temperatures. As expected, the shorter the wall length the more intense the deposition concentration, heat accumulation, and, thus, geometric deviation. This behavior was more evident and premature for the NC strategy due to its lower heat sinking effectiveness. The main finding was that, regardless of the thermal management technique applied, if the same interpass temperature is selected and maintained, the geometry of the part being built tends to be stable and very similar. However, the total deposition time is somewhat shorter with the NIAC technique due its greater heat sinking advantage. Thus, the NIAC technique facilitates the non-stop manufacturing of small parts and details via WAAM.

Welding of Large Thickness Super Duplex Stainless Steel: Microstructure and Properties

In this study, Submerged Arc Welding (SAW) and Gas Metal Arc Welding (GMAW) processes were used in multi-pass welding of 33 mm thickness super duplex stainless steel plates. Recommended and higher than recommended arc energy and interpass temperatures were used. Both GMAW and SAW processes were able to produce large thickness weldments meeting the microstructural, mechanical, and corrosion resistance requirements, and also when using higher than recommended arc energy and interpass temperature. It was possible to reduce the number of welding passes by half when using higher than recommended arc energy and interpass temperature. The SAW process needed only half of the welding time required for the GMAW process to produce a weldment with nearly the same number of weld passes, when using recommended arc energy and interpass temperature. Based on the results of this investigation, the practical recommendations for welding large thicknesses should be revised and updated.

Estimation Method of Interpass Time for the Control of Temperature during a Directed Energy Deposition Process of a Ti–6Al–4V Planar Layer

Directed energy deposition (DED) provides a promising additive manufacturing method to fabricate and repair large metallic parts. However, it may suffer from excessive heat accumulation due to a high build rate, particularly during a wire feeding-type DED process. The implementation of interpass time in between two depositions of beads plays an important process role to passively control the interpass temperature. In this study, a method to estimate the proper interpass time using regression analysis from heat transfer finite element analysis is proposed for maintaining the interpass temperature during a wire feeding-type DED deposition of a planar layer. The overlapping beads of a planar layer are estimated using a polygonal-shaped bead profile in the finite element model. From the estimated proper interpass time, a selected proper interpass time scheme (PITS) is suggested for practical implementation. The selected PITS is applied in a thermo-mechanical finite element model to evaluate the temperature distribution and its effects on the depth of the melt pool, the depth of the heat-affected zone (HAZ), displacement, and residual stresses. By comparing the predicted results with those using a constant interpass time scheme (CITS), the selected PITS shows better control in reducing the depths of the melt pool and HAZ without severely inducing large displacement and residual stresses.