Pre Test Calculations on TOPFLOW PTS Experiment With NEPTUNE_CFD Code

2011 ◽  
Author(s):  
A. Martin ◽  
C. Raynaud ◽  
P. Pe´turaud ◽  
C. Heib ◽  
F. Dubois ◽  
...  
Keyword(s):  
Two Phase Flow ◽  
Test Procedure ◽  
Operating Conditions ◽  
Experimental Program ◽  
Phase Flow ◽  
Two Phase ◽  
Loss Of Coolant Accident ◽  
Flow Configurations ◽  
Definition Of ◽  
Physical Phenomena

Hypothetical Small Break Loss Of Coolant Accident is identified as one of the most severe transients leading to a potential huge Pressurized Thermal Shock on the Reactor Pressure Vessel (RPV). This may result in two-phase flow configurations in the cold legs, according to the operating conditions, and to reliably assess the RPV wall integrity, advanced two-phase flow simulations are required. Related needs in development and/or validation of these advanced models are important, and the ongoing TOPFLOW-PTS experimental program was designed to provide a well documented data base to meet these needs. This paper focuses on pre-test NEPTUNE_CFD simulations of TOPFLOW-PTS experiments; these simulations were performed to (i) help in the definition of the test matrix and test procedure, and (ii) check the presence of the different key physical phenomena at the mock-up scale.

Upward Vertical Two-Phase Flow Through an Annulus—Part II: Modeling Bubble, Slug, and Annular Flow

1992 ◽  
Vol 114 (1) ◽  
pp. 14-30 ◽  
Author(s):  
E. F. Caetano ◽  
O. Shoham ◽  
J. P. Brill
Keyword(s):  
Flow Pattern ◽  
Annular Flow ◽  
Two Phase Flow ◽  
Flow Behavior ◽  
Bubble Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Flow Through ◽  
Physical Phenomena ◽  
Good Agreement

Mechanistic models have been developed for each of the existing two-phase flow patterns in an annulus, namely bubble flow, dispersed bubble flow, slug flow, and annular flow. These models are based on two-phase flow physical phenomena and incorporate annulus characteristics such as casing and tubing diameters and degree of eccentricity. The models also apply the new predictive means for friction factor and Taylor bubble rise velocity presented in Part I. Given a set of flow conditions, the existing flow pattern in the system can be predicted. The developed models are applied next for predicting the flow behavior, including the average volumetric liquid holdup and the average total pressure gradient for the existing flow pattern. In general, good agreement was observed between the experimental data and model predictions.

A Visual and Photographic Study of the Inception of Vaporization in Adiabatic Flow

1964 ◽  
Vol 86 (2) ◽  
pp. 257-261 ◽  
Author(s):  
E. P. Mikol ◽  
J. C. Dudley
Keyword(s):  
Experimental Method ◽  
Two Phase Flow ◽  
Operating Conditions ◽  
Phase Flow ◽  
Two Phase ◽  
Adiabatic Flow ◽  
Index Data ◽  
Flow Phenomena ◽  
Glass Tubes

Data and observations obtained during the study of two-phase flow phenomena for refrigerants flowing in small bore copper and glass tubes have been examined for their significance to the cavitation. Visual and photographic observations have been made of the inception of vaporization and of the movement of the point of inception as operating conditions are varied. Liquid tension has been deduced as occurring in these tests. Liquid tension and cavitation index data are presented. The experimental method is recommended as a means for studying many aspects of the phenomenon of cavitation.

Experiment of Adiabatic Two-Phase Flow in an Annulus Under Low-Frequency Vibration

2012 ◽  
Author(s):  
Shao-Wen Chen ◽  
Caleb S. Brooks ◽  
Chris Macke ◽  
Takashi Hibiki ◽  
Mamoru Ishii ◽  
...  
Keyword(s):  
Void Fraction ◽  
Two Phase Flow ◽  
Low Frequency ◽  
Flow Regimes ◽  
Operating Conditions ◽  
Phase Flow ◽  
Two Phase ◽  
Specific Flow ◽  
Low Frequency Vibration ◽  
Fft Analysis

In order to investigate the possible effect of seismic vibration on two-phase flow dynamics and thermal-hydraulics of a nuclear reactor, experimental tests of adiabatic air-water two-phase flow under low-frequency vibration were carried out in this study. An eccentric cam vibration module operated at low motor speed (up to 390rpm) was attached to an annulus test section which was scaled down from a prototypic BWR fuel assembly sub-channel. The inner and outer diameters of the annulus are 19.1mm and 38.1mm, respectively. The two-phase flow operating conditions cover the ranges of 0.03≤<jg> ≤1.46m/s and 0.25≤<jf>≤1.00m/s and the vibration displacement ranges from ±0.8mm to ±22.2mm. Steady-state area-averaged instantaneous and time-averaged void fraction was recorded and analyzed in stationary and vibration experiments. A neural network flow regime identification technique and fast Fourier transformation (FFT) analysis were introduced to analyze the flow regimes and void signals under stationary and vibration conditions. Experimental results reveal possible changes in flow regimes under specific flow and vibration conditions. In addition, the instantaneous void fraction signals were affected and shown by FFT analysis. Possible reasons for the changes include the applied high acceleration and/or induced resonance at certain ports under the specific flow and vibration conditions.

Ex-Situ Characterization of Two-Phase Flow Regimes in Proton-Exchange Membrane Fuel Cells Under Non-Isothermal Conditions

2010 ◽  
Author(s):  
Arganthae¨l Berson ◽  
Jon G. Pharoah
Keyword(s):  
Proton Exchange Membrane ◽  
Two Phase Flow ◽  
Metal Foam ◽  
Flow Regimes ◽  
Proton Exchange ◽  
Operating Conditions ◽  
Ex Situ ◽  
Phase Flow ◽  
Two Phase ◽  
Exchange Membrane

Efficient water management is crucial for the good performances of proton-exchange membrane fuel cells (PEMFCs). The geometric and physical characteristics of the components of a PEMFC as well as operating conditions have an impact on the transport of water through the porous transport layer (PTL) and the two-phase flow regimes in the microchannels. One parameter of importance is the local temperature, which affects properties such as surface tension and is coupled with phase change. Indeed, a temperature difference of about 5K is expected across the PTL, with spatial variations due to the geometry of the flow field plate. We present preliminary results obtained with a first experimental setup for the ex-situ characterization of two-phase flow regimes in the flow channels. Water is pushed through the PTL, which is sandwiched between a porous metal foam and the flow field plate. The air flow rate, temperature and humidity can be controlled. The cell can be heated up by applying an electrical current through the metal foam. A transparent window is located on top of the flow channel. The two-phase flow within the micro-channels is visualized using a high-speed camera and laser-induced fluorescence. Preliminary results obtained under isothermal conditions at room temperature show that different two-phase flow regimes occur in the channels depending on the operating conditions, in good qualitative agreement with data from the literature. Eventually, a new visualization cell is presented that is expected to correct the flaws of the previous design and will allow a better thermal control. It will be possible to adjust the temperature gradient and the mean temperature in order to observe their impact on two-phase flow regimes for different types of PTL and flow rates. The results will provide a better understanding of water transport in PEMFC and benchmark data for the validation of numerical models.

Micro-Scale Two-Phase Flow Heat Transport Device Driven by Electrohydrodynamic Conduction Pumping

2013 ◽  
Author(s):  
Viral K. Patel ◽  
Jamal Seyed-Yagoobi
Keyword(s):  
Heat Transport ◽  
Two Phase Flow ◽  
Operating Conditions ◽  
Electrode Spacing ◽  
Working Fluid ◽  
Phase Flow ◽  
Two Phase ◽  
Micro Scale ◽  
Flow Heat ◽  
Transport Device

Micro-scale two-phase flow heat transport involves specialized devices that are used to remove large amounts of heat from small surface areas. They operate by circulating a working fluid through a heated space which causes phase change from liquid to vapor. During this process, a significant amount of heat is transported away from the heat source. Micro-scale heat transport devices are compact in size and the heat transfer coefficient can be orders of magnitude higher than in macro-scale for similar operating conditions. Thus, it is of interest to develop such devices for cooling of next-generation electronics and other applications with extremely large heat fluxes. The heat transport device presented in this paper is driven by electrohydrodynamic (EHD) conduction pumping. In EHD conduction pumping, when an electric field is applied to a dielectric liquid, flow is induced. The pump is installed in a two-phase flow loop and has a circular 1 mm diameter cross section with electrode spacing on the order of 120 μm. It acts to circulate the fluid in the loop and has a simple yet robust, non-mechanical design. Results from two-phase flow experiments show that it is easily controlled and such electrically driven pumps can effectively be used in heat transport systems.

Numerical Modeling of Two-Phase Flow Distribution Inside Evaporator Headers

2014 ◽  
Vol 6 (3) ◽  
Author(s):  
Miad Yazdani ◽  
Abbas A. Alahyari ◽  
Hailing Wu ◽  
Thomas D. Radcliff
Keyword(s):  
Heat Exchanger ◽  
Two Phase Flow ◽  
Flow Distribution ◽  
Operating Conditions ◽  
Phase Flow ◽  
Predictive Tool ◽  
Two Phase ◽  
Imaging Results ◽  
Discretization Schemes ◽  
Long Time

Two-phase flow distribution inside evaporator headers has been a challenging problem for a long time and having a robust predictive tool could substantially alleviate the costs associated with experimentation with different concepts and configurations. The use of a two-phase CFD model to predict flow distribution inside the header and at the discharge ports is demonstrated in this paper. The numerical domain is comprised of an inlet pipe and a distributor tube representing the header with a series of discharge ports. The flow distribution was initially verified using an air–water experiment, where the two-phase modeling approach, mesh requirements, and discretization schemes were defined. Next, the model was used to predict distribution of R134a in a typical heat exchanger distributor. The flow distribution across the discharge ports was provided to a discretized correlation-based heat exchanger model to predict the temperature and quality distribution along the length of the heat exchanger. The resultant temperature distribution is validated against IR imaging results for various operating conditions and header orientations.

Flow-Induced Vibration Model for Steam Generator Tubes in Two-Phase Flow

2008 ◽  
Author(s):  
Njuki W. Mureithi ◽  
Soroush Shahriary ◽  
Michel J. Pettigrew
Keyword(s):  
Force Field ◽  
Steam Generator ◽  
Two Phase Flow ◽  
Operating Conditions ◽  
Phase Flow ◽  
Two Phase Flows ◽  
Two Phase ◽  
Fluid Force ◽  
Vibration Stability ◽  
Steam Generator Tubes

While steam generators operate in two-phase flow, the complex nature of the flow makes the prediction of flow-induced fluidelastic instability of steam generator tubes a challenging problem yet to be solved. In the work reported here, the quasi-static fluid force-field, which is the important unknown for two-phase flows, is measured in a rotated-triangle tube bundle for a series of void fractions and flow velocities. The forces are shown to be strongly dependent on void fraction, flow rates and relative tube positions. The fluid force field is then employed along with quasi-steady vibration stability models, originally developed for single phase flows, to model the two-phase flow problem and predict the critical instability velocity. The results are compared with dynamic vibration stability tests and are shown to be in good agreement. The present work uncovers some of the complexities of the fluid force field in two-phase flows. The database provides new potential to designers to estimate expected fluid dynamic loads under operating conditions. The force field data may also be applied in dynamic computations for tube wear simulations, replacing the simple Connors’ model which is currently used.

Numerical Modeling of Two-Phase Flow Distribution Inside Evaporator Headers

2012 ◽  
Author(s):  
Miad Yazdani ◽  
Hailing Wu ◽  
Abbas A. Alahyari ◽  
Thomas D. Radcliff
Keyword(s):  
Heat Exchanger ◽  
Two Phase Flow ◽  
Flow Distribution ◽  
Operating Conditions ◽  
Phase Flow ◽  
Predictive Tool ◽  
Two Phase ◽  
Imaging Results ◽  
Discretization Schemes ◽  
Long Time

Two-phase flow distribution inside evaporator headers has been a challenging problem for a long time and having a robust predictive tool could substantially alleviate the costs associated with experimentation with different concepts and configurations. The use of a two-phase CFD model to predict flow distribution inside the header and at the discharge ports is demonstrated in this paper. The numerical domain is comprised of an inlet pipe and a distributor tube representing the header with a series of discharge ports. The flow distribution was initially verified using an air-water experiment, where the two-phase modeling approach, mesh requirements, and discretization schemes were defined. Next, the model was used to predict distribution of R134a in a typical heat exchanger distributor. The flow distribution across the discharge ports was provided to a discretized correlation-based heat exchanger model to predict the temperature and quality distribution along the length of the heat exchanger. The resultant temperature distribution is validated against IR imaging results for various operating conditions and header configurations.

Numerical Simulation for Two-Phase Flows in Fuel Cell Minichannels

2011 ◽  
Vol 8 (4) ◽  
Author(s):  
Jean-Baptiste Dupont ◽  
Dominique Legendre ◽  
Anna Maria Morgante
Keyword(s):  
Fuel Cell ◽  
Numerical Simulations ◽  
Two Phase Flow ◽  
Numerical Code ◽  
Experimental Investigations ◽  
Pressure Jump ◽  
Phase Flow ◽  
Two Phase Flows ◽  
Two Phase ◽  
Flow Configurations

This work presents direct numerical simulations of two-phase flows in fuel cell minichannels. Different two-phase flow configurations can be observed in such minichannels, which depend on gas-flow rate, liquid holdup, and wettability of each wall. These flows are known to have a significant impact on the fuel cell’s performance. The different two-phase flow configurations must be studied specially concerning the prediction of the transition among them. In the fuel cell minichannels, experimental investigations are difficult to perform because of the small size of the device and the difficult control of the wettability properties of the walls. In such systems, numerical approach can provide useful information with a perfect control of the flow characteristics, particularly for the wettability aspect. The numerical code used in this study is the JADIM code developed at IMFT, which is based on a “volume of fluid” method for interface capturing without any interface reconstruction. The numerical description of the surface tension is one of the crucial points in studying such systems where capillary effects control the phase distribution. The static and the dynamics of the triple line between the liquid, the gas, and the wall is also an essential physical mechanism to consider. The numerical implementation of this model is validated in simple situations where analytical solutions are available for the shape and the pressure jump at the interface. In this paper we present the characteristics of the JADIM code and its potential for the studies of the fuel cell internal flows. Numerical simulations on the two-phase flows on walls, in corners, and inside channels are shown.

scholarly journals STUDY OF PROCESSES IN LAVAL NOZZLE FOR STEAM-LIQUID JET

2019 ◽  
pp. 431-435
Author(s):  
N.T. Niiazov ◽  
N.K. Dzhamankyzov ◽  
А.А. Asanov
Keyword(s):  
Laval Nozzle ◽  
Two Phase Flow ◽  
Liquid Jet ◽  
Phase Flow ◽  
Two Phase ◽  
Experimental Stand ◽  
Definition Of

The article deals with the study of processes in the Laval nozzle, the definition of optimal angles of jet opening. A description of the experimental stand for the study of a two-phase flow is given.

Sign in / Sign up

Export Citation Format

Share Document