A Study on the Effect of Non-Idealized Crack on a 90° Elbow by Using Finite Element Analysis

2018 ◽  
Author(s):  
Jae-Hee Kim ◽  
Min-Kyu Kim ◽  
Ye-Rin Choi ◽  
Doo-Ho Cho ◽  
Moon Ki Kim ◽  
...  
Keyword(s):  
Finite Element ◽  
Numerical Study ◽  
Limit Load ◽  
Element Model ◽  
Assessment Method ◽  
Accurate Solution ◽  
Fe Model ◽  
Plastic Limit ◽  
Element Analysis ◽  
Plastic Limit Load

The present paper proposed the modified limit load solution related to code case N-513-4 which is currently actively researched. To apply to assessment method for an elbow in code case N-513-4, the crack should be postulated as the idealized circumferential through-wall crack (TWC). For this reason, it could be led to overestimate the results due to the assumption of real crack shape. Then, the many research which is related to an accurate solution for a straight pipe by considering realistic crack has been investigated. However, the accurate solution for the elbow with non-idealized TWC is still lacked. Therefore, based on three-dimensional finite element model, the effect of non-idealized circumferential TWC on plastic limit load was investigated under internal pressure. To do this, the finite element (FE) model and analysis procedure employed in the present numerical study were validated by comparing the present finite element analyses result with existing solutions for idealized TWC in the elbow. Then, the correction factor for calculating plastic limit load was newly proposed as a tabulated form by considering practical ranges of geometry.

Analysis and Experiments on the Plastic Limit Load of Elbows under Combined Pressure and In-Plane Closing Bending Moment

2013 ◽  
Vol 774-776 ◽  
pp. 1090-1097 ◽  
Author(s):  
Zhi Xiang Duan ◽  
Kun Shi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Safety Assessment ◽  
Bending Moment ◽  
Limit Load ◽  
Experimental Results ◽  
Plastic Limit ◽  
Element Analysis ◽  
Limit Pressure ◽  
Plastic Limit Load

This paper discusses the plastic limit load of elbows without defects and with local thinned area (LTA) in the extrados under combined pressure and in-plane closing bending moment. Finite element analysis (FEA) and experiments have been used. The results of FEA show that, for the elbows without defects, when the ratio of pressure to the limit pressure (P/PL) is smaller than 0.469, the limit moment of elbows increases with the increasing pressure; when the ratio (P/PL) is bigger than 0.469, the limit moment of elbow decreases with the increasing pressure. For the elbows with LTA, the FEA results show that with different LTA the variation of the limit load of elbows to the pressure is different. Perhaps, the limit moment of elbows always decreases with the increasing pressure. It is also likely that the limit moment of elbows increases with the increasing pressure and then decreases with the increasing pressure. The results of FEA are consistent with the experimental results. By fitting the results of FEA, the safety assessment figure for elbows under combined pressure and in-plane closing bending moment is drawn.

Plastic Analysis for Cylindrical Vessels Under In-Plane Moment on the Nozzle

2010 ◽  
Vol 132 (6) ◽  
Author(s):  
B. H. Wu ◽  
Z. F. Sang ◽  
G. E. O. Widera
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Limit Load ◽  
Cylindrical Vessel ◽  
Plastic Limit ◽  
Element Analysis ◽  
Test Models ◽  
Scale Test ◽  
Plastic Limit Load

The objective of this paper is to determine the plastic limit moment for cylindrical vessels with a nozzle under in-plane moment loading. Three full scale test models with different d/D ratios were fabricated for the experiment. A three-dimensional nonlinear finite element analysis was also performed. The plastic limit moment of the cylindrical vessel-nozzle connections was determined approximately by the twice-elastic-slope criterion. The results indicate that the plastic limit moments obtained by the experiment and finite element analysis are in good agreement. On the basis of the above results, a parametric analysis of the plastic limit moment for cylindrical vessels under in-plane moment on the nozzle was carried out, and an empirical formula is proposed. The results can serve as a supplement to the available data of plastic limit load for cylindrical vessel-nozzle connection structures under external load.

Use of Limit Load Analysis for Design of Pressure Vessel Cover

2012 ◽  
Author(s):  
Rahul Jain
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Pressure Vessel ◽  
Limit Load ◽  
Plastic Limit ◽  
Element Analysis ◽  
Linear Elastic ◽  
Reference Volume ◽  
Plastic Limit Load ◽  
Load Analysis

This paper explores the use of limit load analysis methods for the design of a pressure vessel manway cover as per the ASME boiler and pressure vessel code guidelines. The results of elastic and limit load finite element analysis are discussed for the design. The concept of reference volume consideration along with linear elastic finite element analysis to determine the lower bound limit load has been explored and the results are compared with the non-linear elastic-plastic limit load analysis.

Plastic Limit Loads of Pad Reinforced Cylindrical Vessels Under Out-of-Plane Moment of Nozzle

2005 ◽  
Vol 128 (1) ◽  
pp. 49-56 ◽  
Author(s):  
Z. F. Sang ◽  
H. F. Wang ◽  
L. P. Xue ◽  
G. E. O. Widera
Keyword(s):  
Finite Element ◽  
Limit Load ◽  
Plastic Limit ◽  
Element Analysis ◽  
Limit Loads ◽  
Test Models ◽  
Out Of Plane ◽  
Scale Test ◽  
Plastic Limit Load ◽  
Strain Responses

The purpose of this work is to study the plastic limit load of pad reinforced cylindrical vessels with different d/D ratios under out-of-plane moment loading on a nozzle. Three full-scale test models were designed and fabricated. A 3-D nonlinear finite element numerical analysis was also performed. Data on plastic limit moment is obtained from load-displacement and load-strain responses. The results indicate that plastic limit loads determined by test (including displacement and strain measurements) and finite element analysis are in agreement.

Finite Element Analysis of the Distributed Vibration Absorbers for Structural Noise Control

2005 ◽  
Author(s):  
Ashwini Gautam ◽  
Chris Fuller ◽  
James Carneal
Keyword(s):  
Finite Element ◽  
Numerical Model ◽  
Base Plate ◽  
Element Model ◽  
Fe Model ◽  
Vibration Absorbers ◽  
Element Analysis ◽  
Poroelastic Media ◽  
Hexahedral Elements ◽  
Component Models

This work presents an extensive analysis of the properties of distributed vibration absorbers (DVAs) and their effectiveness in controlling the sound radiation from the base structure. The DVA acts as a distributed mass absorber consisting of a thin metal sheet covering a layer of acoustic foam (porous media) that behaves like a distributed spring-mass-damper system. To assess the effectiveness of these DVAs in controlling the vibration of the base structures (plate) a detailed finite elements model has been developed for the DVA and base plate structure. The foam was modeled as a poroelastic media using 8 node hexahedral elements. The structural (plate) domain was modeled using 16 degree of freedom plate elements. Each of the finite element models have been validated by comparing the numerical results with the available analytical and experimental results. These component models were combined to model the DVA. Preliminary experiments conducted on the DVAs have shown an excellent agreement between the results obtained from the numerical model of the DVA and from the experiments. The component models and the DVA model were then combined into a larger FE model comprised of a base plate with the DVA treatment on its surface. The results from the simulation of this numerical model have shown that there has been a significant reduction in the vibration levels of the base plate due to DVA treatment on it. It has been shown from this work that the inclusion of the DVAs on the base plate reduces their vibration response and therefore the radiated noise. Moreover, the detailed development of the finite element model for the foam has provided us with the capability to analyze the physics behind the behavior of the distributed vibration absorbers (DVAs) and to develop more optimized designs for the same.

scholarly journals Design and analysis of concrete-filled tubular flange girders under combined loading

2021 ◽  
pp. 136943322110015
Author(s):  
Rana Al-Dujele ◽  
Katherine Ann Cashell
Keyword(s):  
Finite Element ◽  
Axial Force ◽  
Failure Modes ◽  
Numerical Study ◽  
Combined Loading ◽  
Torsional Stiffness ◽  
Fe Model ◽  
Combined Effects ◽  
Element Analysis ◽  
Hollow Section

This paper is concerned with the behaviour of concrete-filled tubular flange girders (CFTFGs) under the combination of bending and tensile axial force. CFTFG is a relatively new structural solution comprising a steel beam in which the compression flange plate is replaced with a concrete-filled hollow section to create an efficient and effective load-carrying solution. These members have very high torsional stiffness and lateral torsional buckling strength in comparison with conventional steel I-girders of similar depth, width and steel weight and are there-fore capable of carrying very heavy loads over long spans. Current design codes do not explicitly include guidance for the design of these members, which are asymmetric in nature under the combined effects of tension and bending. The current paper presents a numerical study into the behaviour of CFTFGs under the combined effects of positive bending and axial tension. The study includes different loading combinations and the associated failure modes are identified and discussed. To facilitate this study, a finite element (FE) model is developed using the ABAQUS software which is capable of capturing both the geometric and material nonlinearities of the behaviour. Based on the results of finite element analysis, the moment–axial force interaction relationship is presented and a simplified equation is proposed for the design of CFTFGs under combined bending and tensile axial force.

Finite Element Mesh Generator Applying Constraints’ Propagation and Isoparametric Mapping

1991 ◽  
Author(s):  
J. Rodriguez ◽  
M. Him
Keyword(s):  
Finite Element ◽  
Mesh Generation ◽  
Element Model ◽  
Finite Element Mesh ◽  
Fe Model ◽  
Element Analysis ◽  
Element Mesh ◽  
Mesh Generator ◽  
Generation Algorithm ◽  
Essential Input

Abstract This paper presents a finite element mesh generation algorithm (PREPAT) designed to automatically discretize two-dimensional domains. The mesh generation algorithm is a mapping scheme which creates a uniform isoparametric FE model based on a pre-partitioned domain of the component. The proposed algorithm provides a faster and more accurate tool in the pre-processing phase of a Finite Element Analysis (FEA). A primary goal of the developed mesh generator is to create a finite element model requiring only essential input from the analyst. As a result, the generator code utilizes only a sketch, based on geometric primitives, and information relating to loading/boundary conditions. These conditions represents the constraints that are propagated throughout the model and the available finite elements are uniformly mapped in the resulting sub-domains. Relative advantages and limitations of the mesh generator are discussed. Examples are presented to illustrate the accuracy, efficiency and applicability of PREPAT.

J-Integral Analysis of Surface Cracks in Round Bars under Bending Moments

2011 ◽  
Vol 52-54 ◽  
pp. 43-48 ◽  
Author(s):  
Al Emran Ismail ◽  
Ahmad Kamal Ariffin ◽  
Shahrum Abdullah ◽  
Mariyam Jameelah Ghazali ◽  
Ruslizam Daud
Keyword(s):  
Finite Element ◽  
Crack Depth ◽  
Crack Tip ◽  
Bending Moment ◽  
Limit Load ◽  
Fe Model ◽  
Surface Cracks ◽  
Element Analysis ◽  
Reference Stress ◽  
Proposed Model

This paper presents a non-linear numerical investigation of surface cracks in round bars under bending moment by using ANSYS finite element analysis (FEA). Due to the symmetrical analysis, only quarter finite element (FE) model was constructed and special attention was given at the crack tip of the cracks. The surface cracks were characterized by the dimensionless crack aspect ratio, a/b = 0.6, 0.8, 1.0 and 1.2, while the dimensionless relative crack depth, a/D = 0.1, 0.2 and 0.3. The square-root singularity of stresses and strains was modeled by shifting the mid-point nodes to the quarter-point locations close to the crack tip. The proposed model was validated with the existing model before any further analysis. The elastic-plastic analysis under remotely applied bending moment was assumed to follow the Ramberg-Osgood relation with n = 5 and 10. J values were determined for all positions along the crack front and then, the limit load was predicted using the J values obtained from FEA through the reference stress method.

Sign in / Sign up

Export Citation Format

Share Document