Analysis and Experiments on the Plastic Limit Load of Elbows under Combined Pressure and In-Plane Closing Bending Moment

2013 ◽  
Vol 774-776 ◽  
pp. 1090-1097 ◽  
Author(s):  
Zhi Xiang Duan ◽  
Kun Shi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Safety Assessment ◽  
Bending Moment ◽  
Limit Load ◽  
Experimental Results ◽  
Plastic Limit ◽  
Element Analysis ◽  
Limit Pressure ◽  
Plastic Limit Load

This paper discusses the plastic limit load of elbows without defects and with local thinned area (LTA) in the extrados under combined pressure and in-plane closing bending moment. Finite element analysis (FEA) and experiments have been used. The results of FEA show that, for the elbows without defects, when the ratio of pressure to the limit pressure (P/PL) is smaller than 0.469, the limit moment of elbows increases with the increasing pressure; when the ratio (P/PL) is bigger than 0.469, the limit moment of elbow decreases with the increasing pressure. For the elbows with LTA, the FEA results show that with different LTA the variation of the limit load of elbows to the pressure is different. Perhaps, the limit moment of elbows always decreases with the increasing pressure. It is also likely that the limit moment of elbows increases with the increasing pressure and then decreases with the increasing pressure. The results of FEA are consistent with the experimental results. By fitting the results of FEA, the safety assessment figure for elbows under combined pressure and in-plane closing bending moment is drawn.

Plastic Analysis for Cylindrical Vessels Under In-Plane Moment on the Nozzle

2010 ◽  
Vol 132 (6) ◽  
Author(s):  
B. H. Wu ◽  
Z. F. Sang ◽  
G. E. O. Widera
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Limit Load ◽  
Cylindrical Vessel ◽  
Plastic Limit ◽  
Element Analysis ◽  
Test Models ◽  
Scale Test ◽  
Plastic Limit Load

The objective of this paper is to determine the plastic limit moment for cylindrical vessels with a nozzle under in-plane moment loading. Three full scale test models with different d/D ratios were fabricated for the experiment. A three-dimensional nonlinear finite element analysis was also performed. The plastic limit moment of the cylindrical vessel-nozzle connections was determined approximately by the twice-elastic-slope criterion. The results indicate that the plastic limit moments obtained by the experiment and finite element analysis are in good agreement. On the basis of the above results, a parametric analysis of the plastic limit moment for cylindrical vessels under in-plane moment on the nozzle was carried out, and an empirical formula is proposed. The results can serve as a supplement to the available data of plastic limit load for cylindrical vessel-nozzle connection structures under external load.

Use of Limit Load Analysis for Design of Pressure Vessel Cover

2012 ◽  
Author(s):  
Rahul Jain
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Pressure Vessel ◽  
Limit Load ◽  
Plastic Limit ◽  
Element Analysis ◽  
Linear Elastic ◽  
Reference Volume ◽  
Plastic Limit Load ◽  
Load Analysis

This paper explores the use of limit load analysis methods for the design of a pressure vessel manway cover as per the ASME boiler and pressure vessel code guidelines. The results of elastic and limit load finite element analysis are discussed for the design. The concept of reference volume consideration along with linear elastic finite element analysis to determine the lower bound limit load has been explored and the results are compared with the non-linear elastic-plastic limit load analysis.

Capacity Analysis of PE Pipeline With Non-Planar Defect

2013 ◽  
Author(s):  
Weijie Jiang ◽  
Jianping Zhao ◽  
Dingyue Chen
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Constitutive Model ◽  
Mechanical Performance ◽  
Orthogonal Design ◽  
Bending Moment ◽  
Limit Load ◽  
Capacity Analysis ◽  
Element Analysis ◽  
Load Factors

A tensile test of buried PE pipe is designed to test the mechanical performance. Then the constitutive model for the PE pipe can be established. The limit load of the PE pipe with local thinning defect can be studied with the method of combining the orthogonal design of experiment and finite element analysis. Then the factors of local thinning defect pipe limit load factors can be analyzed. The results show that the depth of the defect has a great effect on the limit load (internal pressure and bending moment) of PE pipe. The effects that the axial length of the defect and the circumferential length of the defect have on the limit load are not significant.

Plastic Limit Pressure of Pressurized Cylinders With Hillside Nozzle

2006 ◽  
Author(s):  
H. F. Wang ◽  
Z. F. Sang ◽  
L. P. Xue ◽  
G. E. O. Widera
Keyword(s):  
Finite Element ◽  
Limit Load ◽  
Experimental Models ◽  
Plastic Limit ◽  
Element Analysis ◽  
Design Guideline ◽  
Limit Pressure ◽  
Test Models ◽  
Scale Test ◽  
Plastic Limit Pressure

Cylinder-nozzle intersections are widely used in pressure vessel and piping industries. In order to get better mixing and energy exchange of the reactants, pipe-nozzle intersection with hillside nozzle is applied more and more widely. The purpose of this work is to investigate the plastic limit load of cylinders with hillside nozzle subjected to internal pressure. Three full-scale test models with different angles of the hillside nozzle were designed and fabricated specially for the test using strain gagues. 3-D finite element numerical simulations on the experimental models were performed. Based on both results, a group of basic data on plastic limit pressure defined by double elastic-slope method for cylinders with hillside nozzle is approximately obtained according to load-strain responses, and the plastic limit pressures determined by test and finite element analysis are in good agreement. The results indicate that the limit pressure increases with the increment of the angle of the hillside nozzle, and compared with radial nozzles in cylinders, the hillside nozzles have higher limit pressure, which can be served as the basis for developing a design guideline for pressurized cylinders with various angles of hillside nozzle.

scholarly journals Plastic limit load of ellipsoidal pressure vessel head with nozzle under internal pressure loading

2013 ◽  
Vol 18 (4) ◽  
pp. 1263-1274 ◽  
Author(s):  
V.N. Skopinsky ◽  
N.A. Berkov ◽  
A.B. Smetankin
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Limit Load ◽  
Rate Of Change ◽  
Pressure Loading ◽  
Plastic Limit ◽  
Elastic Plastic ◽  
Limit Pressure ◽  
Plastic Limit Load ◽  
Plastic Limit Pressure

Abstract A new method and numerical procedure for determining the plastic limit load in an ellipsoid-cylinder intersection using the elastic-plastic finite element analysis are presented. The proposed method is based on the maximum criterion of the rate of change of the relative plastic work. For the elastic-plastic analysis of the nozzle connections the 2D finite element method and plasticity theory with strain hardening are used. The results of the comparison of the plastic limit pressure obtained on the basis of different known criteria and the proposed criterion are presented. A parametric study of ellipsoidal heads with a nozzle under internal pressure loading was performed. The effects of nondimensional geometric parameters of shell intersection on the plastic limit pressure are discussed.

The Limit Load Interactions of the Brazed Aluminum Plate-Fin Heat Exchanger Header Under Combined Piping Loads

2011 ◽  
Vol 133 (3) ◽  
Author(s):  
Wei Wang ◽  
Liang Chen ◽  
Caidong Guo
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Heat Exchanger ◽  
Axial Force ◽  
Shear Force ◽  
Bending Moment ◽  
Limit Load ◽  
Force Component ◽  
Element Analysis ◽  
Interaction Curves

In order to investigate the strength design problem of the brazed aluminum plate-fin heat exchanger header under complex external piping loads, the limit load interactions of the header under combined piping loads are studied in this paper. To establish the limit piping load interaction curves, nonlinear finite element analysis assuming the elastic perfectly plastic material model is performed by using the commercial finite element analysis software ANSYS and multiple piping load combinations, which are the combination of orthogonal bending moment components, torque component-shear force component, bending moment component-axial force component, compound bending moment-axial force component, and torque component-compound shear force, of the header with six opening ratios ranging from 0.5 to 1 are explored. The results of the interaction diagrams show that the feasible combined piping load zone of the header derived from the interaction curves can be simplified as a triangular zone determined by the individual limit piping load components safely and the simplified feasible zone is suggested to be used for establishing a simplified safety assessment method for the header under combined piping loads.

A Study on the Effect of Non-Idealized Crack on a 90° Elbow by Using Finite Element Analysis

2018 ◽  
Author(s):  
Jae-Hee Kim ◽  
Min-Kyu Kim ◽  
Ye-Rin Choi ◽  
Doo-Ho Cho ◽  
Moon Ki Kim ◽  
...  
Keyword(s):  
Finite Element ◽  
Numerical Study ◽  
Limit Load ◽  
Element Model ◽  
Assessment Method ◽  
Accurate Solution ◽  
Fe Model ◽  
Plastic Limit ◽  
Element Analysis ◽  
Plastic Limit Load

The present paper proposed the modified limit load solution related to code case N-513-4 which is currently actively researched. To apply to assessment method for an elbow in code case N-513-4, the crack should be postulated as the idealized circumferential through-wall crack (TWC). For this reason, it could be led to overestimate the results due to the assumption of real crack shape. Then, the many research which is related to an accurate solution for a straight pipe by considering realistic crack has been investigated. However, the accurate solution for the elbow with non-idealized TWC is still lacked. Therefore, based on three-dimensional finite element model, the effect of non-idealized circumferential TWC on plastic limit load was investigated under internal pressure. To do this, the finite element (FE) model and analysis procedure employed in the present numerical study were validated by comparing the present finite element analyses result with existing solutions for idealized TWC in the elbow. Then, the correction factor for calculating plastic limit load was newly proposed as a tabulated form by considering practical ranges of geometry.

Strength Behavior of Hot-Tapped Pipeline Under Internal Pressure Load

2011 ◽  
Vol 133 (5) ◽  
Author(s):  
B. H. Wu ◽  
Z. F. Sang ◽  
Z. L. Wang ◽  
G. E. O. Widera
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Internal Pressure ◽  
Three Dimensional ◽  
Plastic Limit ◽  
Element Analysis ◽  
Pressure Load ◽  
Limit Pressure ◽  
Strength Behavior ◽  
Plastic Limit Pressure

The objective of this study is to investigate the strength behavior and plastic limit pressure of hot-tapped pipelines under an internal pressure load. Two full scale test models were fabricated for the experiment. A three-dimensional nonlinear finite element analysis was also carried out. The plastic limit pressure was determined approximately by use of the twice the elastic-slope criterion. The results indicate that plastic limit pressures obtained by experiment and finite element analysis are in good agreement. On the basis of the above results, a parametric analysis of the plastic limit pressure was carried out and resulted in the development of formulas useful for the design of hot-tapped pipelines.

Plastic Limit Loads of Pad Reinforced Cylindrical Vessels Under Out-of-Plane Moment of Nozzle

2005 ◽  
Vol 128 (1) ◽  
pp. 49-56 ◽  
Author(s):  
Z. F. Sang ◽  
H. F. Wang ◽  
L. P. Xue ◽  
G. E. O. Widera
Keyword(s):  
Finite Element ◽  
Limit Load ◽  
Plastic Limit ◽  
Element Analysis ◽  
Limit Loads ◽  
Test Models ◽  
Out Of Plane ◽  
Scale Test ◽  
Plastic Limit Load ◽  
Strain Responses

The purpose of this work is to study the plastic limit load of pad reinforced cylindrical vessels with different d/D ratios under out-of-plane moment loading on a nozzle. Three full-scale test models were designed and fabricated. A 3-D nonlinear finite element numerical analysis was also performed. Data on plastic limit moment is obtained from load-displacement and load-strain responses. The results indicate that plastic limit loads determined by test (including displacement and strain measurements) and finite element analysis are in agreement.

Sign in / Sign up

Export Citation Format

Share Document