Determination of Transition From Thin Shell to Thick Shell Theory for Torispherical Heads With Head Dish Radius to Thickness Ratios Under 20

2020 ◽  
Author(s):  
Barry Millet ◽  
Kaveh Ebrahimi
Keyword(s):  
Internal Pressure ◽  
Transition Point ◽  
Limit Load ◽  
Thick Wall ◽  
Ratio Test ◽  
Thin Wall ◽  
Plastic Limit ◽  
Element Analysis ◽  
Perfectly Plastic ◽  
Plastic Limit Load

Abstract This paper will clarify the point of transition where the behavior of the dish of a torispherical head goes from thin wall theory (collapse failure and membrane) to thick wall (burst failure) as the head dish radius to thickness ratios (L/t) gets smaller. There are several stated ratio limits for this transition. Three separate Welding Research Bulletins WRC 364 New Design Curves for Torispherical Heads[1], WRC 444 Buckling Criteria for Torispherical Heads Under Internal Pressure [3] and, WRC 501 Design of Torispherical and Ellipsoidal Heads Subjected to Internal Pressure[4] each provide a different definition of the transition point, that being 16.67, 15 and 20 respectively. This paper will review the actual test performed for L/t ratios from 20 down to 15 (which is the lowest ratio test run) and provide the results of a numerical desktop study in lieu of actual testing. Linear elastic, elastic perfectly plastic limit load and elastic plastic limit load finite element analysis will be parametrically run across many L/t ratios and the knuckle radius will be varied across the runs. The results will be reviewed to check through wall behavior to find the transition point of thin to thick wall behavior. These will also be compared against the existing ASME BVP Section VIII Division 2 [5] formulas.

Shakedown and Limit Analysis of Kinematic Hardening Piping Elbows Under Internal Pressure and Bending Moments

2021 ◽  
Author(s):  
Heng Peng ◽  
Yinghua Liu
Keyword(s):  
Yield Strength ◽  
Internal Pressure ◽  
Limit Analysis ◽  
Kinematic Hardening ◽  
Limit Load ◽  
Bending Moments ◽  
Plastic Limit ◽  
Plastic Limit Load ◽  
Interaction Curves ◽  
Shakedown Limit

Abstract In this paper, the Stress Compensation Method (SCM) adopting an elastic-perfectly-plastic (EPP) material is further extended to account for limited kinematic hardening (KH) material model based on the extended Melan's static shakedown theorem using a two-surface model defined by two hardening parameters, namely the initial yield strength and the ultimate yield strength. Numerical analysis of a cylindrical pipe is performed to validate the outcomes of the extended SCM. The results agree well with ones from literature. Then the extended SCM is applied to the shakedown and limit analysis of KH piping elbows subjected to internal pressure and cyclic bending moments. Various loading combinations are investigated to generate the shakedown limit and the plastic limit load interaction curves. The effects of material hardening, elbow angle and loading conditions on the shakedown limit and the plastic limit load interaction curves are presented and analysed. The present method is incorporated in the commercial finite element simulation software and can be considered as a general computational tool for shakedown analysis of KH engineering structures. The obtained results provide a useful information for the structural design and integrity assessment of practical piping elbows.

Plastic Limit Loads for Piping Branch Junctions

2007 ◽  
Vol 345-346 ◽  
pp. 1377-1380 ◽  
Author(s):  
Yun Jae Kim ◽  
Kuk Hee Lee ◽  
Chi Yong Park
Keyword(s):  
Three Dimensional ◽  
Limit Load ◽  
Plastic Limit ◽  
Perfectly Plastic ◽  
Plastic Materials ◽  
Wide Range ◽  
Pipe Radius ◽  
Plastic Limit Load ◽  
The Mean ◽  
Elastic Perfectly Plastic

The present work presents plastic limit load solutions for branch junctions under internal pressure and in-plane bending, based on detailed three-dimensional (3-D) FE limit analyses using elastic-perfectly plastic materials. The proposed solutions are valid for a wide range of branch junction geometries; ratios of the branch-to-run pipe radius and thickness from 0.0 to 1.0, and the mean radius-to-thickness ratio of the run pipe from 5.0 to 20.0.

Research on Safety Assessment Method for Pressure Pipe With Incomplete Welding Defects Under Complicated Loadings

2010 ◽  
Author(s):  
Zhijiang Jin ◽  
Xianping Wan ◽  
Chenghang Jiang
Keyword(s):  
Internal Pressure ◽  
Safety Assessment ◽  
Limit Load ◽  
Assessment Method ◽  
Curved Surface ◽  
Assessment Procedure ◽  
Plastic Limit ◽  
Pressure Pipe ◽  
Welding Defects ◽  
Plastic Limit Load

Since most pressure pipe materials have good toughness, the failure mode of pipe is usually the plastic failure controlled by limit load. The incomplete welding defect is very common in the pipe, and its existence will reduce the load-carrying capacity of pipes. The pipe with incomplete welding defects can be continued using only after passing the appropriate safety assessment, so the research on safety assessment procedure for pressure pipe with incomplete welding defects under combined bending, torsion and internal pressure loadings has a great theoretical and practical engineering value. By using theoretical analyzing method of plastic limit load, the plastic limit load of pressure pipe with different defect size or pipe diameter ratio are calculated in this paper, then safety assessment curved surface and its express equation are obtained by fitting calculation data. Finally a safety assessment procedure is developed for pressure pipes under combined bending, torsion and internal pressure loadings according to the curved surface.

scholarly journals Plastic limit load of ellipsoidal pressure vessel head with nozzle under internal pressure loading

2013 ◽  
Vol 18 (4) ◽  
pp. 1263-1274 ◽  
Author(s):  
V.N. Skopinsky ◽  
N.A. Berkov ◽  
A.B. Smetankin
Keyword(s):  
Finite Element ◽  
Internal Pressure ◽  
Limit Load ◽  
Rate Of Change ◽  
Pressure Loading ◽  
Plastic Limit ◽  
Elastic Plastic ◽  
Limit Pressure ◽  
Plastic Limit Load ◽  
Plastic Limit Pressure

Abstract A new method and numerical procedure for determining the plastic limit load in an ellipsoid-cylinder intersection using the elastic-plastic finite element analysis are presented. The proposed method is based on the maximum criterion of the rate of change of the relative plastic work. For the elastic-plastic analysis of the nozzle connections the 2D finite element method and plasticity theory with strain hardening are used. The results of the comparison of the plastic limit pressure obtained on the basis of different known criteria and the proposed criterion are presented. A parametric study of ellipsoidal heads with a nozzle under internal pressure loading was performed. The effects of nondimensional geometric parameters of shell intersection on the plastic limit pressure are discussed.

Analysis and Experiments on the Plastic Limit Load of Elbows under Combined Pressure and In-Plane Closing Bending Moment

2013 ◽  
Vol 774-776 ◽  
pp. 1090-1097 ◽  
Author(s):  
Zhi Xiang Duan ◽  
Kun Shi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Safety Assessment ◽  
Bending Moment ◽  
Limit Load ◽  
Experimental Results ◽  
Plastic Limit ◽  
Element Analysis ◽  
Limit Pressure ◽  
Plastic Limit Load

This paper discusses the plastic limit load of elbows without defects and with local thinned area (LTA) in the extrados under combined pressure and in-plane closing bending moment. Finite element analysis (FEA) and experiments have been used. The results of FEA show that, for the elbows without defects, when the ratio of pressure to the limit pressure (P/PL) is smaller than 0.469, the limit moment of elbows increases with the increasing pressure; when the ratio (P/PL) is bigger than 0.469, the limit moment of elbow decreases with the increasing pressure. For the elbows with LTA, the FEA results show that with different LTA the variation of the limit load of elbows to the pressure is different. Perhaps, the limit moment of elbows always decreases with the increasing pressure. It is also likely that the limit moment of elbows increases with the increasing pressure and then decreases with the increasing pressure. The results of FEA are consistent with the experimental results. By fitting the results of FEA, the safety assessment figure for elbows under combined pressure and in-plane closing bending moment is drawn.

Analytical Limit Loads for Tube Sections With Circumferential Degradation

2004 ◽  
Author(s):  
W. Reinhardt ◽  
X. Wang
Keyword(s):  
Analytical Solutions ◽  
Load Capacity ◽  
Bending Moment ◽  
Limit Load ◽  
Thin Wall ◽  
Plastic Limit ◽  
Tubes And Pipes ◽  
Limit Loads ◽  
Plastic Limit Load ◽  
Analytical Limit

The fracture mechanics evaluation of tubes and pipes with circumferential degradation typically requires that the plastic limit load capacity be evaluated under a combination of axial force and bending moment loading. Most available analytical solutions are thin-wall approximations and may not work well for heavy-wall applications. The present paper derives an analytical limit load for a cylindrical pipe or tube with a partial circumferential, partial through-wall flaw and its bounding cases (through wall partial circumferential and uniform circumferential part-throughwall flaw). The solution is not in closed form, but can be easily solved with available mathematical software like MathCAD. The obtained limit loads for a steam generator tube are compared to those from simplified analytical solutions. The effect of tube supports on the limit load of a tube with non-axisymmetric flaw is discussed with a simplified model.

Sign in / Sign up

Export Citation Format

Share Document