Improved crystalline quality of Al-rich n-AlGaN by regrowth on nanoporous template fabricated by electrochemical etching

2018 ◽  
Vol 12 (04) ◽  
pp. 1 ◽  
Author(s):  
Liang Zhang ◽  
Jianchang Yan ◽  
Qingqing Wu ◽  
Yanan Guo ◽  
Chao Yang ◽  
...  
Author(s):  
Alain Claverie ◽  
Zuzanna Liliental-Weber

GaAs layers grown by MBE at low temperatures (in the 200°C range, LT-GaAs) have been reported to have very interesting electronic and transport properties. Previous studies have shown that, before annealing, the crystalline quality of the layers is related to the growth temperature. Lowering the temperature or increasing the layer thickness generally results in some columnar polycrystalline growth. For the best “temperature-thickness” combinations, the layers may be very As rich (up to 1.25%) resulting in an up to 0.15% increase of the lattice parameter, consistent with the excess As. Only after annealing are the technologically important semi-insulating properties of these layers observed. When annealed in As atmosphere at about 600°C a decrease of the lattice parameter to the substrate value is observed. TEM studies show formation of precipitates which are supposed to be As related since the average As concentration remains almost unchanged upon annealing.


Nanomaterials ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 928
Author(s):  
Yong Du ◽  
Zhenzhen Kong ◽  
Muhammet Toprak ◽  
Guilei Wang ◽  
Yuanhao Miao ◽  
...  

This work presents the growth of high-quality Ge epilayers on Si (001) substrates using a reduced pressure chemical vapor deposition (RPCVD) chamber. Based on the initial nucleation, a low temperature high temperature (LT-HT) two-step approach, we systematically investigate the nucleation time and surface topography, influence of a LT-Ge buffer layer thickness, a HT-Ge growth temperature, layer thickness, and high temperature thermal treatment on the morphological and crystalline quality of the Ge epilayers. It is also a unique study in the initial growth of Ge epitaxy; the start point of the experiments includes Stranski–Krastanov mode in which the Ge wet layer is initially formed and later the growth is developed to form nuclides. Afterwards, a two-dimensional Ge layer is formed from the coalescing of the nuclides. The evolution of the strain from the beginning stage of the growth up to the full Ge layer has been investigated. Material characterization results show that Ge epilayer with 400 nm LT-Ge buffer layer features at least the root mean square (RMS) value and it’s threading dislocation density (TDD) decreases by a factor of 2. In view of the 400 nm LT-Ge buffer layer, the 1000 nm Ge epilayer with HT-Ge growth temperature of 650 °C showed the best material quality, which is conducive to the merging of the crystals into a connected structure eventually forming a continuous and two-dimensional film. After increasing the thickness of Ge layer from 900 nm to 2000 nm, Ge surface roughness decreased first and then increased slowly (the RMS value for 1400 nm Ge layer was 0.81 nm). Finally, a high-temperature annealing process was carried out and high-quality Ge layer was obtained (TDD=2.78 × 107 cm−2). In addition, room temperature strong photoluminescence (PL) peak intensity and narrow full width at half maximum (11 meV) spectra further confirm the high crystalline quality of the Ge layer manufactured by this optimized process. This work highlights the inducing, increasing, and relaxing of the strain in the Ge buffer and the signature of the defect formation.


2015 ◽  
Vol 414 ◽  
pp. 15-20 ◽  
Author(s):  
Pornsiri Wanarattikan ◽  
Sakuntam Sanorpim ◽  
Somyod Denchitcharoen ◽  
Kenjiro Uesugi ◽  
Shigeyuki Kuboya ◽  
...  

2002 ◽  
Vol 41 (Part 1, No. 6B) ◽  
pp. 4299-4303 ◽  
Author(s):  
Yong Suk Cho ◽  
Junggeun Jhin ◽  
Eui Kwan Koh ◽  
Young Ju Park ◽  
Eun Kyu Kim ◽  
...  
Keyword(s):  
Ion Beam ◽  

2014 ◽  
Vol 887-888 ◽  
pp. 766-769 ◽  
Author(s):  
Huey Ling Chang ◽  
Chih Ming Chen ◽  
Chin Huang Sun ◽  
Jin Shyong Lin

This study produced a regularly arranged membrane, called anodic aluminum oxide (referred AAO), by mean of anodic oxidation treatment. The structure of AAO can be molecular self-assembly and its pore size is consistent. Also, the manufacturing process cost is low. These properties make the AAO be a nanotemplate material. This study further created a high quality of nanostructured film by electrochemical mould with the design of electrolyzer. In addition, a uniform nanothin film was grown on the aluminum surface in the stable control of current and temperature according to the conditions of different anode treatment. This film can form a nanopore array which the diameter can be controlled the size ranging from 15 nm to 400 nm. As results, the study can produce nanoporous template for various aperture by mean of anodic oxidation.


Sign in / Sign up

Export Citation Format

Share Document