Adding tactile realism to a virtual reality laparoscopic surgical simulator with a cost-effective human interface device

Author(s):  
Ian W. Mack ◽  
Stephen Potts ◽  
Karen R. McMenemy ◽  
R. S. Ferguson
Author(s):  
T.V. Zhemchuzhkina ◽  
T.V. Nosova ◽  
V.B. Vassilenko ◽  
D.Kh. Shtofel ◽  
Y.P. Liskov ◽  
...  

2019 ◽  
Vol 2 (1) ◽  
Author(s):  
Chelsey Wallace, M.S. ◽  
Zahra Nourmohammadi, Ph.D. ◽  
David A. Zopf, M.D., M.S.

Background and Hypothesis: Protruding ears, also known as prominauris, are prevalent worldwide at an occurrence rate of about 5%. Children with prominauris report lower self-esteem and experience increased teasing and social isolation at school. From a functional standpoint, protruding ears can make wearing prescription glasses difficult. This increased stress and anxiety and impaired functionality lead children and families to seek treatment. One of the most effective treatments for protruding ears is otoplasty. This procedure involves an incision in the back of the ear and the placement of non-resorbable sutures to reform the ear. Alternatively, the procedure can be performed using an incisionless technique. As this is an elective procedure done commonly in children, adequate education of medical trainees is critical to ensure the proper level of skill is attained and patient satisfaction is maximized. Currently, teaching otoplasty is done with cadavers and supervised procedures with an attending. Surgical simulators are employed in the instruction of a variety of surgical procedures and allow residents to practice in a zero-risk environment. In addition, 3D printing has facilitated the development of surgical simulators allowing for a more cost-effective, consistent, and anatomically correct simulator. We developed an ear model made from silicone for trainees to practice traditional and incisionless otoplasty. Project Methods: The otoplasty surgical simulator was developed by isolating an ear from a computed-tomography scan in the Materialise software to create a 3D model. This model was then altered to create a negative mold. The mold was printed using fusion deposition printing with 1.75 MM polylactic acid filament. After printing, the mold was filled with Dragon Skin Silicone Shore 20 to simulate ear cartilage. The model was then coated in a layer of Dragon Skin Silicone Shore 10 to simulate a layer of skin. Conclusion and Potential Impact: This otoplasty simulator will next be validated by expert surgeons and then used in a surgical simulation workshop for surgical trainees. Because of the low-cost of the surgical simulator and the ease of manufacturing, this simulator can also be used to train surgeons abroad where access to surgical training may not be readily available. 


10.2196/17425 ◽  
2020 ◽  
Vol 22 (3) ◽  
pp. e17425
Author(s):  
Daniel Katz ◽  
Ronak Shah ◽  
Elizabeth Kim ◽  
Chang Park ◽  
Anjan Shah ◽  
...  

Background The incidence of cardiac arrests per year in the United States continues to increase, yet in-hospital cardiac arrest survival rates significantly vary between hospitals. Current methods of training are expensive, time consuming, and difficult to scale, which necessitates improvements in advanced cardiac life support (ACLS) training. Virtual reality (VR) has been proposed as an alternative or adjunct to high-fidelity simulation (HFS) in several environments. No evaluations to date have explored the ability of a VR program to examine both technical and behavioral skills and demonstrate a cost comparison. Objective This study aimed to explore the utility of a voice-based VR ACLS team leader refresher as compared with HFS. Methods This prospective observational study performed at an academic institution consisted of 25 postgraduate year 2 residents. Participants were randomized to HFS or VR training and then crossed groups after a 2-week washout. Participants were graded on technical and nontechnical skills. Participants also completed self-assessments about the modules. Proctors were assessed for fatigue and task saturation, and cost analysis based on local economic data was performed. Results A total of 23 of 25 participants were included in the scoring analysis. Fewer participants were familiar with VR compared with HFS (9/25, 36% vs 25/25, 100%; P<.001). Self-reported satisfaction and utilization scores were similar; however, significantly more participants felt HFS provided better feedback: 99 (IQR 89-100) vs 79 (IQR 71-88); P<.001. Technical scores were higher in the HFS group; however, nontechnical scores for decision making and communication were not significantly different between modalities. VR sessions were 21 (IQR 19-24) min shorter than HFS sessions, the National Aeronautics and Space Administration task load index scores for proctors were lower in each category, and VR sessions were estimated to be US $103.68 less expensive in a single-learner, single-session model. Conclusions Utilization of a VR-based team leader refresher for ACLS skills is comparable with HFS in several areas, including learner satisfaction. The VR module was more cost-effective and was easier to proctor; however, HFS was better at delivering feedback to participants. Optimal education strategies likely contain elements of both modalities. Further studies are needed to examine the utility of VR-based environments at scale.


CISM journal ◽  
1988 ◽  
Vol 42 (2) ◽  
pp. 121-125 ◽  
Author(s):  
Roy Gagnon

Cadastral maps generated from digitizing tabloids have too many sources of error to be reliable when plotted at large scales. To improve the 1:1000 cadastral map, three numerical methods were tested during twenty-seven mapping projects. The systems studied were: complex number similarity transformation, simultaneous similarity transformation, and iterative similarity transformation. There were several “human interface” difficulties with the computer routines but all of the programs were found to be reliable, and cost effective. All of the resulting cadastral maps are in daily use. Numerical transformation was found superior to digital methods of cadastral compilation.


2018 ◽  
Vol 25 (7) ◽  
pp. S93
Author(s):  
A.K. Dubin ◽  
D. Julian ◽  
P. Mattingly ◽  
R. Smith

2011 ◽  
Vol 1 ◽  
pp. 00094
Author(s):  
Marina Vela Nuñez ◽  
Carlo Avizzano ◽  
Denis Mottet ◽  
Massimo Bergamasco

Sign in / Sign up

Export Citation Format

Share Document