Initiating Rotation in Back and Reverse Armstand Triple Somersaults Tuck Dives

2001 ◽  
Vol 17 (4) ◽  
pp. 312-325 ◽  
Author(s):  
Karen Murtaugh ◽  
Doris I. Miller
Keyword(s):  
Angular Momentum ◽  
Lower Extremity ◽  
Upper Extremity ◽  
Reaction Force ◽  
Moment Arm ◽  
Angular Momenta ◽  
Force Moment ◽  
The Moment ◽  
Trunk Position

To determine strategies for initiating rotation in armstand back and reverse triple somersaults tuck dives from the 10-m platform, videotaped records of 17 elite male divers performing in competitions between 1995 and 1999 were analyzed. Linear and angular momenta at last contact were similar for both dives. Although the lower extremity actions were comparable, they occurred significantly earlier (p < .05) in reverse triple takeoffs, allowing divers to enter the tuck more quickly. As divers lean, the moment arm of the vertical platform reaction force increases with respect to the CG. The vertical platform reaction force moment promotes back and opposes reverse somersaulting angular momentum. Meanwhile, the horizontal platform reaction force moment promotes reverse and opposes back somersaulting angular momentum. Consequently, divers performing reverse triples maintained a more vertical trunk position during the early part of the takeoff, while those executing back triples leaned further before initiating lower and upper extremity actions to exert force against the platform. Since the strategy for reverse rotation may result in the head passing close to the platform and there is very little to gain in degree of difficulty, it is recommended that competitors execute back rather than reverse somersaulting armstand dives.

A Robotic Ankle–Foot Prosthesis With Active Alignment

2016 ◽  
Vol 10 (2) ◽  
Author(s):  
Andrew Kennedy LaPrè ◽  
Brian R. Umberger ◽  
Frank C. Sup
Keyword(s):  
Center Of Pressure ◽  
Reaction Force ◽  
Residual Limb ◽  
Moment Arm ◽  
Ankle Prosthesis ◽  
Socket Connection ◽  
The Moment ◽  
Socket Interface ◽  
Configuration Changes ◽  
Large Moment

An ankle–foot prosthesis designed to mimic the missing physiological limb generates a large sagittal moment during push off which must be transferred to the residual limb through the socket connection. The large moment is correlated with high internal socket pressures that are often a source of discomfort for the person with amputation, limiting prosthesis use. In this paper, the concept of active alignment is developed. Active alignment realigns the affected residual limb toward the center of pressure (CoP) during stance. During gait, the prosthesis configuration changes to shorten the moment arm between the ground reaction force (GRF) and the residual limb. This reduces the peak moment transferred through the socket interface during late stance. A tethered robotic ankle prosthesis has been developed, and evaluation results are presented for active alignment during normal walking in a laboratory setting. Preliminary testing was performed with a subject without amputation walking with able-bodied adapters at a constant speed. The results show a 33% reduction in the peak resultant moment transferred at the socket limb interface.

scholarly journals A Forefoot Strike Requires the Highest Forces Applied to the Foot Among Foot Strike Patterns

2017 ◽  
Vol 01 (02) ◽  
pp. E37-E42 ◽  
Author(s):  
Satoru Hashizume ◽  
Toshio Yanagiya
Keyword(s):  
Achilles Tendon ◽  
Ground Reaction Force ◽  
Reaction Force ◽  
Moment Arm ◽  
Moment Arms ◽  
Joint Reaction Forces ◽  
Force Moment ◽  
Foot Strike ◽  
Reaction Forces ◽  
Joint Reaction

AbstractGround reaction force is often used to predict the potential risk of injuries but may not coincide with the forces applied to commonly injured regions of the foot. This study examined the forces applied to the foot, and the associated moment arms made by three foot strike patterns. 10 male runners ran barefoot along a runway at 3.3 m/s using forefoot, midfoot, and rearfoot strikes. The Achilles tendon and ground reaction force moment arms represented the shortest distance between the ankle joint axis and the line of action of each force. The Achilles tendon and joint reaction forces were calculated by solving equations of foot motion. The Achilles tendon and joint reaction forces were greatest for the forefoot strike (2 194 and 3 137 N), followed by the midfoot strike (1 929 and 2 853 N), and the rearfoot strike (1 526 and 2 394 N). The ground reaction force moment arm was greater for the forefoot strike than for the other foot strikes, and was greater for the midfoot strike than for the rearfoot strike. Meanwhile, there were no differences in the Achilles tendon moment arm among all foot strikes. These differences were attributed mainly to differences in the ground reaction force moment arm among the three foot strike patterns.

The Influence of Heel Lift Manipulation on Achilles Tendon Loading in Running

1998 ◽  
Vol 14 (4) ◽  
pp. 374-389 ◽  
Author(s):  
Sharon J. Dixon ◽  
David G. Kerwin
Keyword(s):  
Achilles Tendon ◽  
Ground Reaction Force ◽  
Reaction Force ◽  
Tendon Injury ◽  
Moment Arm ◽  
The Common ◽  
Tendon Force ◽  
The Moment ◽  
Joint Center ◽  
Heel Lift

In this study, a modeling method was developed to estimate Achilles tendon forces in running. Owing to the common use of heel lift devices in the treatment of Achilles tendon injury, we investigated the influence of increased heel lift on Achilles tendon loading. The hypothesis was that heel lift manipulation can influence maximum Achilles tendon force. Responses to heel lift variation were found to differ among 3 elite runners demonstrating distinct running styles. A rearfoot and a midfoot striker demonstrated significant increases in maximum Achilles tendon force with increased heel lift, whereas a forefoot striker demonstrated no changes in maximum Achilles tendon force values with heel lift manipulation (p < .05). Analysis of the factors contributing to the observed changes in maximum Achilles tendon force highlighted the influence of the moment arm of ground reaction force and the moment arm of the Achilles tendon about the ankle joint center. The finding that increased heel lift may increase maximum Achilles tendon force suggests that caution is advised in the routine use of this intervention. The different responses to heel lift increase between subjects highlight the importance of classifying subjects based on running style.

Effect of Foot Progression Angle and Lateral Wedge Insole on a Reduction in Knee Adduction Moment

2016 ◽  
Vol 32 (5) ◽  
pp. 454-461 ◽  
Author(s):  
Ken Tokunaga ◽  
Yuki Nakai ◽  
Ryo Matsumoto ◽  
Ryoji Kiyama ◽  
Masayuki Kawada ◽  
...  
Keyword(s):  
Ground Reaction Force ◽  
Reaction Force ◽  
Reduction Ratio ◽  
Knee Adduction Moment ◽  
Moment Arm ◽  
3 Dimensional ◽  
Foot Progression Angle ◽  
Close Relationship ◽  
The Moment ◽  
Joint Center

This study evaluated the effect of foot progression angle on the reduction in knee adduction moment caused by a lateral wedged insole during walking. Twenty healthy, young volunteers walked 10 m at their comfortable velocity wearing a lateral wedged insole or control flat insole in 3 foot progression angle conditions: natural, toe-out, and toe-in. A 3-dimensional rigid link model was used to calculate the external knee adduction moment, the moment arm of ground reaction force to knee joint center, and the reduction ratio of knee adduction moment and moment arm. The result indicated that the toe-out condition and lateral wedged insole decreased the knee adduction moment in the whole stance phase. The reduction ratio of the knee adduction moment and the moment arm exhibited a close relationship. Lateral wedged insoles decreased the knee adduction moment in various foot progression angle conditions due to decrease of the moment arm of the ground reaction force. Moreover, the knee adduction moment during the toe-out gait with lateral wedged insole was the smallest due to the synergistic effect of the lateral wedged insole and foot progression angle. Lateral wedged insoles may be a valid intervention for patients with knee osteoarthritis regardless of the foot progression angle.

The Effects of a Lateral Wedge Insole on Knee and Ankle Joints During Slope Walking

2015 ◽  
Vol 31 (6) ◽  
pp. 476-483 ◽  
Author(s):  
Yuki Uto ◽  
Tetsuo Maeda ◽  
Ryoji Kiyama ◽  
Masayuki Kawada ◽  
Ken Tokunaga ◽  
...  
Keyword(s):  
Ground Reaction Force ◽  
Reaction Force ◽  
Force Plate ◽  
Three Dimensional ◽  
Frontal Plane ◽  
Knee Adduction Moment ◽  
Moment Arm ◽  
Level Walking ◽  
Ankle Valgus ◽  
The Moment

The purpose of this study was to determine whether a lateral wedge insole reduces the external knee adduction moment during slope walking. Twenty young, healthy subjects participated in this study. Subjects walked up and down a slope using 2 different insoles: a control flat insole and a 7° lateral wedge insole. A three-dimensional motion analysis system and force plate were used to examine the knee adduction moment, the ankle valgus moment, and the moment arm of the ground reaction force to the knee joint center in the frontal plane. The lateral wedge insole significantly decreased the moment arm of the ground reaction force, resulting in a reduction of the knee adduction moment during slope walking, similar to level walking. The reduction ratio of knee adduction moment by the lateral wedge insole during the early stance of up-slope walking was larger than that of level walking. Conversely, the lateral wedge insole increased the ankle valgus moment during slope walking, especially during the early stance phase of up-slope walking. Clinicians should examine the utilization of a lateral wedge insole for knee osteoarthritis patients who perform inclined walking during daily activity, in consideration of the load on the ankle joint.

Combining Values

2002 ◽  
Vol 7 (2) ◽  
pp. 1-4, 12 ◽  
Author(s):  
Christopher R. Brigham
Keyword(s):  
Lower Extremity ◽  
Upper Extremity ◽  
Evaluation Method ◽  
Proximal Phalanx ◽  
Common Error ◽  
The Third ◽  
Whole Person ◽  
Impairment Ratings ◽  
Upper Extremity Impairment ◽  
The Individual

Abstract To account for the effects of multiple impairments, evaluating physicians must provide a summary value that combines multiple impairments so the whole person impairment is equal to or less than the sum of all the individual impairment values. A common error is to add values that should be combined and typically results in an inflated rating. The Combined Values Chart in the AMA Guides to the Evaluation of Permanent Impairment, Fifth Edition, includes instructions that guide physicians about combining impairment ratings. For example, impairment values within a region generally are combined and converted to a whole person permanent impairment before combination with the results from other regions (exceptions include certain impairments of the spine and extremities). When they combine three or more values, physicians should select and combine the two lowest values; this value is combined with the third value to yield the total value. Upper extremity impairment ratings are combined based on the principle that a second and each succeeding impairment applies not to the whole unit (eg, whole finger) but only to the part that remains (eg, proximal phalanx). Physicians who combine lower extremity impairments usually use only one evaluation method, but, if more than one method is used, the physician should use the Combined Values Chart.

Spinal Impairment Evaluation: Fifth Edition Changes

2001 ◽  
Vol 6 (1) ◽  
pp. 1-3
Author(s):  
Robert H. Haralson
Keyword(s):  
Spinal Cord ◽  
Lower Extremity ◽  
Range Of Motion ◽  
Upper Extremity ◽  
Spinal Cord Injuries ◽  
Clinical Findings ◽  
Fourth Edition ◽  
Treatment Results ◽  
Standard Terminology ◽  
Made In

Abstract The AMA Guides to the Evaluation of Permanent Impairment (AMA Guides), Fifth Edition, was published in November 2000 and contains major changes from its predecessor. In the Fourth Edition, all musculoskeletal evaluation and rating was described in a single chapter. In the Fifth Edition, this information has been divided into three separate chapters: Upper Extremity (13), Lower Extremity (14), and Spine (15). This article discusses changes in the spine chapter. The Models for rating spinal impairment now are called Methods. The AMA Guides, Fifth Edition, has reverted to standard terminology for spinal regions in the Diagnosis-related estimates (DRE) Method, and both it and the Range of Motion (ROM) Method now reference cervical, thoracic, and lumbar. Also, the language requiring the use of the DRE, rather than the ROM Method has been strengthened. The biggest change in the DRE Method is that evaluation should include the treatment results. Unfortunately, the Fourth Edition's philosophy regarding when and how to rate impairment using the DRE Model led to a number of problems, including the same rating of all patients with radiculopathy despite some true differences in outcomes. The term differentiator was abandoned and replaced with clinical findings. Significant changes were made in evaluation of patients with spinal cord injuries, and evaluators should become familiar with these and other changes in the Fifth Edition.

scholarly journals APPLICATION OF DOMAIN INTEGRATED DESIGN METHODOLOGY FOR BIO-INSPIRED DESIGN- A CASE STUDY OF SUTURE PIN DESIGN

2021 ◽  
Vol 1 ◽  
pp. 487-496
Author(s):  
Pavan Tejaswi Velivela ◽  
Nikita Letov ◽  
Yuan Liu ◽  
Yaoyao Fiona Zhao
Keyword(s):  
Cross Sections ◽  
Design Methodology ◽  
Reaction Force ◽  
Integrated Design ◽  
Total Deformation ◽  
Insertion Force ◽  
Force Reaction ◽  
The Moment ◽  
Work Done

AbstractThis paper investigates the design and development of bio-inspired suture pins that would reduce the insertion force and thereby reducing the pain in the patients. Inspired by kingfisher's beak and porcupine quills, the conceptual design of the suture pin is developed by using a unique ideation methodology that is proposed in this research. The methodology is named as Domain Integrated Design, which involves in classifying bio-inspired structures into various domains. There is little work done on such bio-inspired multifunctional aspect. In this research we have categorized the vast biological functionalities into domains namely, cellular structures, shapes, cross-sections, and surfaces. Multi-functional bio-inspired structures are designed by combining different domains. In this research, the hypothesis is verified by simulating the total deformation of tissue and the needle at the moment of puncture. The results show that the bio-inspired suture pin has a low deformation on the tissue at higher velocities at the puncture point and low deformation in its own structure when an axial force (reaction force) is applied to its tip. This makes the design stiff and thus require less force of insertion.

scholarly journals Lower Extremity Biomechanics Predicts Major League Baseball Player Performance

2021 ◽  
Vol 9 (7) ◽  
pp. 232596712110152
Author(s):  
Lucas G. Teske ◽  
Edward C. Beck ◽  
Garrett S. Bullock ◽  
Kristen F. Nicholson ◽  
Brian R. Waterman
Keyword(s):  
Lower Extremity ◽  
Major League Baseball ◽  
Reaction Force ◽  
Regression Trees ◽  
Minimal Detectable Change ◽  
Vertical Force ◽  
Baseball Players ◽  
Major League ◽  
Lower Extremity Biomechanics ◽  
Statistical Metrics

Background: Although lower extremity biomechanics has been correlated with traditional metrics among baseball players, its association with advanced statistical metrics has not been evaluated. Purpose: To establish normative biomechanical parameters during the countermovement jump (CMJ) among Major League Baseball (MLB) players and evaluate the relationship between CMJ-developed algorithms and advanced statistical metrics. Study Design: Cohort study; Level of evidence, 3. Methods: MLB players in 2 professional organizations performed the CMJ at the beginning of each baseball season from 2013 to 2017. We collected ground-reaction force data including the eccentric rate of force development (“load”), concentric vertical force (“explode”), and concentric vertical impulse (“drive”) as well as the Sparta Score. The advanced statistical metrics from each baseball season (eg, fielding independent pitching [FIP], weighted stolen base runs [wSB], and weighted on-base average) were also gathered for the study participants. The minimal detectable change (MDC) was calculated for each CMJ variable to establish normative parameters. Pearson coefficient analysis and regression trees were used to evaluate associations between CMJ data and advanced statistical metrics for the players. Results: A total of 151 pitchers and 138 batters were included in the final analysis. The MDC for “load,” “explode,” “drive,” and the Sparta Score was 10.3, 8.1, 8.7, and 4.6, respectively, and all demonstrated good reliability (intraclass correlation coefficient > 0.75). There was a weak but statistically significant correlation between the Sparta Score and wSB ( r = 0.23; P = .007); however, there were no significant correlations with any other advanced metrics. Regression trees demonstrated superior FIP with higher Sparta Scores in older pitchers compared with younger pitchers. Conclusion: There was a positive but weak correlation between the Sparta Score and base-stealing performance among professional baseball players. Additionally, older pitchers with a higher Sparta Score had statistically superior FIP compared with younger pitchers with a similar Sparta Score after adjusting for age.

Sign in / Sign up

Export Citation Format

Share Document