Effect of a ceramic coating on the characteristic of surface combustion

2016 ◽  
Vol 10 (5) ◽  
pp. 774-779 ◽  
Author(s):  
N. Ya. Vasilik ◽  
V. M. Shmelev
Keyword(s):  
Ceramic Coating ◽  
Surface Combustion

Characterization of thermal barrier coatings formed by electon-beam physical vapor deposition (EB-PVD)

1989 ◽  
Vol 47 ◽  
pp. 426-427
Author(s):  
Ozer Unal
Keyword(s):  
Thermal Barrier Coatings ◽  
Physical Vapor Deposition ◽  
Ceramic Coating ◽  
High Vacuum ◽  
Ceramic Coatings ◽  
High Energy ◽  
Thermal Barrier ◽  
Protective Oxide ◽  
Barrier Coatings ◽  
Energy Beam

Interest in ceramics as thermal barrier coatings for hot components of turbine engines has increased rapidly over the last decade. The primary reason for this is the significant reduction in heat load and increased chemical inertness against corrosive species with the ceramic coating materials. Among other candidates, partially-stabilized zirconia is the focus of attention mainly because ot its low thermal conductivity and high thermal expansion coefficient.The coatings were made by Garrett Turbine Engine Company. Ni-base super-alloy was used as the substrate and later a bond-coating with high Al activity was formed over it. The ceramic coatings, with a thickness of about 50 μm, were formed by EB-PVD in a high-vacuum chamber by heating the target material (ZrO2-20 w/0 Y2O3) above its evaporation temperaturef >3500 °C) with a high-energy beam and condensing the resulting vapor onto a rotating heated substrate. A heat treatment in an oxidizing environment was performed later on to form a protective oxide layer to improve the adhesion between the ceramic coating and substrate. Bulk samples were studied by utilizing a Scintag diffractometer and a JEOL JXA-840 SEM; examinations of cross-sectional thin-films of the interface region were performed in a Philips CM 30 TEM operating at 300 kV and for chemical analysis a KEVEX X-ray spectrometer (EDS) was used.

Damage of aluminum samples with alumina ceramic coating under pulsed energy flows of various nature

2018 ◽  
pp. 15-27 ◽  
Author(s):  
V. A. Gribkov ◽  
◽  
A. S. Demin ◽  
N. A. Epifanov ◽  
E. E. Kazilin ◽  
...  
Keyword(s):  
Ceramic Coating ◽  
Alumina Ceramic ◽  
Energy Flows

Comparison of Focused Ion Beam and Conventional Techniques on Tem Specimen Preparation of Metal-Ceramic Interfaces

1998 ◽  
Vol 4 (S2) ◽  
pp. 860-861 ◽  
Author(s):  
A. Ramirez de Arellano López ◽  
W.-A. Chiou ◽  
K. T. Faber
Keyword(s):  
Focused Ion Beam ◽  
Ceramic Coating ◽  
Steel Substrate ◽  
Ion Beam ◽  
Specimen Preparation ◽  
Inhomogeneous Materials ◽  
Cross Sectional ◽  
Fine Grain ◽  
Basic Industry ◽  
Coated Surface

The results of TEM analyses of materials are critically dependent on the quality of the sample prepared. Although numerous techniques have been developed in the last two decades, differential thinning of inhomogeneous materials remains a serious problem. Recently, focused ion beam (FIB) technique has been introduced for cross-sectional sample preparation for TEM and SEM.A novel system for depositing a fine-grain (∼ 200 nm) ceramic coating on a metal surface via a patent pending Small-Particle Plasma Spray (SPPS) technique has been developed at the Basic Industry Research Laboratory of Northwestern University. To understand the properties of the coated surface, the ceramic/metal interface and the microstructure of the ceramic coating must be investigated. This paper presents a comparison of the microstructure of an A12O3 coating on a mild steel substrate prepared using conventional and FEB techniques.

scholarly journals Microstructure and Wear Behavior of Plasma-Sprayed TiO2–SiAlON Ceramic Coating

Coatings ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1268
Author(s):  
Yun Wang ◽  
Weichao Wan ◽  
Junhong Mao ◽  
Lihui Tian ◽  
Ruitao Li
Keyword(s):  
Ceramic Coating ◽  
Wear Behavior ◽  
Rutile Phase ◽  
Atmospheric Plasma ◽  
Tio2 Anatase ◽  
Sialon Ceramic ◽  
Mating Surface ◽  
Starved Lubrication ◽  
Plasma Sprayed ◽  
Lubrication Conditions

In this study, atmospheric plasma spray was employed to deposit TiO2–SiAlON ceramic coating on 316 stainless steel. The phases and microstructure of the ceramic coating were investigated. Additionally, comparative studies on the tribological performances of the substrate and the ceramic coating, under both dry and starved lubrication conditions, were carried out. The SiAlON phase was preserved, while partial TiO2 anatase was transformed to rutile phase. The wear rate of the coating was roughly 1/3 of that of the substrate under both conditions. The wear mechanisms of the ceramic coating were surface fracture and abrasive wear in both cases, and the coating under starved lubrication underwent less abrasion. The pores in the coating served as micro-reservoirs, forming an oil layer on the mating surface, and improving tribological properties during sliding.

Sign in / Sign up

Export Citation Format

Share Document