scholarly journals In situ equilibrium pore-water pressures derived from partial piezoprobe dissipation tests in marine sediments

2013 ◽  
Vol 50 (12) ◽  
pp. 1294-1305 ◽  
Author(s):  
Nabil Sultan ◽  
Sara Lafuerza
Keyword(s):  
Slope Stability ◽  
Pore Pressure ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Design Parameters ◽  
Short Term ◽  
Pore Water Pressures ◽  
Time Required

Excess pore-water pressure has a significant effect on submarine slope stability and sediment deformation, and therefore its in situ equilibrium measurement is crucial in carrying out accurate slope stability assessments and accurately deriving geotechnical design parameters. In situ equilibrium pore-water pressure is usually obtained from pore pressure decay during piezocone tests. However, submarine shelves and slopes are often characterized by the existence of low-permeability (fine-grained) sediments involving long dissipation tests that are an important issue for offshore operational costs. Consequently, short-term and (or) partial dissipation tests are usually performed and in situ equilibrium pore-water pressures are predicted from partial measurements. Using a modified cavity expansion approach, this paper aims to predict for four different sites the in situ equilibrium pore-water pressures. Comparisons between predicted and observed in situ equilibrium pore-water pressures allowed the development of a guide to evaluate the minimum time required to perform short-term dissipation tests for a given marine sediment. The main finding of this Note is that the second derivative of the pore pressure, u, versus the logarithm of time, t, ∂2u/∂ln(t)2 must be positive to calculate accurately the in situ equilibrium pore-water pressures from partial measurements.

scholarly journals Influences of Pore-Water Pressure on Slope Stability considering Strength Nonlinearity

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Di Wu ◽  
Yuke Wang ◽  
Fei Zhang ◽  
Yue Qiu
Keyword(s):  
Slope Stability ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Pressure Coefficient ◽  
Stability Evaluation ◽  
Slip Surfaces ◽  
Stability Of Slopes ◽  
Pore Water Pressures ◽  
Linear And Nonlinear

The pore-water pressure is a vital factor in determining the slope stability. To deal with the stability of slopes undergoing pore-water pressures, this paper used the pore-water pressure coefficient to develop the three-dimensional limit analysis method for slope stability evaluation with a nonlinear strength envelope. For numerical slope examples, the critical heights and corresponding critical slip surfaces associated with linear and nonlinear envelopes were derived by using a numerical optimization procedure. The influences of pore-water pressures on the slope stability were addressed by comparing the upper-bound solutions derived by linear and nonlinear strength envelopes (the linear and nonlinear results for short). The obtained two critical inclinations between the linear and nonlinear results both decrease and gradually approach with increasing pore-water pressure coefficient. For most slopes subjected to pore-water pressures, using the linear Mohr–Coulomb envelope will obviously overestimate the slope critical height. The overestimation resulted from the linear criterion will become more distinct for slopes with smaller widths. Besides, the presented results showed that the equivalent internal friction angle tends to have a weaker increasing trend for steeper slopes as pore-water pressure coefficient increases. Hence, when pore-water pressure coefficient increases, the critical slip surfaces of gentle slopes with nonlinear strength criteria become shallower, but the critical slip surfaces of steep slopes seem to have no consistent change law. These results and analyses can illustrate the significance of the application of nonlinear strength envelopes in slope stability evaluation considering pore-water pressures and provide certain reference advice in slope engineering design and landslide prevention.

scholarly journals Variation of Pore Water Pressure in Tailing Sand under Dynamic Loading

2018 ◽  
Vol 2018 ◽  
pp. 1-13 ◽  
Author(s):  
Jia-xu Jin ◽  
Hong-zhi Cui ◽  
Li Liang ◽  
Shi-wang Li ◽  
Ping-yi Zhang
Keyword(s):  
Pore Pressure ◽  
Dynamic Loading ◽  
Pore Water ◽  
Vibration Frequency ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Structural Failure ◽  
Slow Increase ◽  
Tailing Dam ◽  
Time Required

Intense vibration affects the pore water pressure in a tailing dam, with the tendency to induce dam liquefaction. In this study, experiments were performed wherein model tailing dams were completely liquefied by sustained horizontal dynamic loading to determine the effects of the vibration frequency, vibration amplitude, and tailing density on the pore water pressure. The results revealed four stages in the increase of the tailing pore water pressure under dynamic loading, namely, a slow increase, a rapid increase, inducement of structural failure, and inducement of complete liquefaction. A lower frequency and smaller amplitude of the vibration were found to increase the time required to achieve a given pore water pressure in dense tailings. Under the effect of these three factors—vibration frequency and amplitude and tailing density—the tailing liquefaction time varied nonlinearly with the height from the base of the tailing dam, with an initial decrease followed by an increase. The pore pressure that induced structural failure also gradually decreased with increasing height. The increase in the tailing pore pressure could be described by an S-shaped model. A complementary multivariate nonlinear equation was also derived for predicting the tailing pore water pressure under dynamic loading.

Failure and post-failure analysis of submarine mass movements using geomorphology and geomechanical concepts

2018 ◽  
Vol 477 (1) ◽  
pp. 333-351 ◽  
Author(s):  
Jacques Locat
Keyword(s):  
Slope Stability ◽  
Failure Analysis ◽  
Rheological Properties ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Mass Movements ◽  
Geotechnical Characteristics ◽  
Time Of Failure

AbstractAccess to submarine slopes is usually limited and it is often difficult to rely on deep cores or in situ measurements to determine the geotechnical characteristics of the sediments involved in a slide when carrying out back-analyses of submarine mass movements and their consequences. The approach presented here uses geomorphology and basic geomechanical concepts to reduce uncertainties in slope stability and mobility analyses. It shows how geomorphology can be used to select the geomechanical input parameters required in failure and post-failure analyses. Typical parameters derived from such analyses are related to the strength of the material, the pore water pressure at the time of failure, and the rheological properties of post-failure debris or mud flows.

Pore-water pressure response during undrained isotropic load changes in layered soils

1999 ◽  
Vol 36 (3) ◽  
pp. 544-555
Author(s):  
K D Eigenbrod ◽  
W H Wurmnest
Keyword(s):  
Pore Pressure ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Pressure Coefficient ◽  
Shear Stresses ◽  
Pressure Equalization ◽  
Pore Water Pressures ◽  
Internal Pore ◽  
Varved Clay

Low pore-water pressure responses observed during undrained isotropic loading of thinly interbedded varved clay specimens were related to internal pore-water pressure equalization and internal shearing between soft clay seams and stiff silt layers of the varved clay. Both processes were analyzed in two separate models: a finite element analysis of the layered soil specimen with different elastic properties for each layer showed that shear stresses can develop along the layer interfaces during undrained isotropic loading. However, because the shear stresses are small and restricted to a narrow zone close to the surface of the cylindrical specimen, it appeared that the effect of shearing on the overall pore-water responses is negligible. The analysis of the pore-water pressures during undrained, isotropic loading demonstrated that hydraulic gradients between the two layers will develop. As a result, pore water will drain from the clay into the silt, leading to consolidation of the clay and swelling of the silt seams. The stabilized pore-water pressures should be the same as the pore-water pressures measured for the overall specimen, if the effect of internal shearing is negligible. Comparison of the computed with the measured overall pore-water pressure responses during testing for Skempton's pore-pressure coefficient B indicated reasonable agreement.Key words: Skempton's pore-pressure coefficient B, pore-water pressure response, varved clays, internal shearing, internal pore-water pressure equalization.

Effect of rainfall on matric suctions in a residual soil slope

1996 ◽  
Vol 33 (4) ◽  
pp. 618-628 ◽  
Author(s):  
T T Lim ◽  
H Rahardjo ◽  
M F Chang ◽  
D G Fredlund
Keyword(s):  
Slope Stability ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Matric Suction ◽  
Residual Soil ◽  
Soil Slope ◽  
Field Instrumentation ◽  
Pore Water Pressures ◽  
Residual Soil Slope

A slope stability study involving shallow slip surfaces should include the effect of negative pore-water pressures in a slope. A field instrumentation program was carried out to monitor negative pore-water pressure (i.e., in situ matric suction) in a residual soil slope in Singapore. Variations in matric suction and the matric suction profiles under (1) a canvas-convered grassed surface, (2) a grassed surface, and (3) a bare ground surface, in response to rainfalls were investigated. Changes in matric suction due to changes in climatic conditions decrease rapidly with depth. The change was found to be most significant in the bare slope and least significant under the canvas-covered slope. The amount of decrease in matric suction after a rainstorm was observed to be a function of the initial matric suction just prior to the rainstorm. Positive pore-water pressures were observed above the groundwater table, suggesting the development of a perched water table within the slope. These observations are also typical of other regions experiencing high seasonal rainfalls. The field monitoring program presented can be adopted for investigating rainfall-induced landslides in other parts of the world. Key words: matric suction, negative pore-water pressure, field instrumentation, rainfall, residual soil, slope stability.

TIME TO THE END OF PRIMARY CONSOLIDATION (EOP) OF SOFT CLAYEY SOILS: CONCERNING THE EFFECT OF ATTERBERG’S LIMIT AND CYCLIC LOADING HISTORY

2019 ◽  
Vol 128 (2B) ◽  
pp. 29-41
Author(s):  
Trần Thanh Nhàn
Keyword(s):  
Cyclic Loading ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Clayey Soils ◽  
Loading History ◽  
Cyclic Shear ◽  
Wide Range ◽  
Primary Consolidation ◽  
Time Required

In order to observe the end of primary consolidation (EOP) of cohesive soils with and without subjecting to cyclic loading, reconstituted specimens of clayey soils at various Atterberg’s limits were used for oedometer test at different loading increments and undrained cyclic shear test followed by drainage with various cyclic shear directions and a wide range of shear strain amplitudes. The pore water pressure and settlement of the soils were measured with time and the time to EOP was then determined by different methods. It is shown from observed results that the time to EOP determined by 3-t method agrees well with the time required for full dissipation of the pore water pressure and being considerably larger than those determined by Log Time method. These observations were then further evaluated in connection with effects of the Atterberg’s limit and the cyclic loading history.

The Test Study to the Changes of Excess Pore Water Pressure during Precast Pile Construction

2012 ◽  
Vol 193-194 ◽  
pp. 1010-1013
Author(s):  
Shu Qing Zhao
Keyword(s):  
Pore Water ◽  
Clayey Soil ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Excess Pore Pressure ◽  
Soil Pressure ◽  
Excess Pore Water Pressure ◽  
Test Study ◽  
Excess Pore

The construct to precast pile in thick clayey soil can cause the accumulation of excess pore water pressure. The high excess pore pressure can make soil, buildings and pipes surrounded have large deflection, even make them injured. Combining with actual projects, this paper presents an in-situ model test on the changes of excess pore water pressure caused by precast pile construct. It is found that the radius of influence range for single pile driven is about 15m，the excess pore water pressure can reach or even exceed the above effective soil pressure, and there are two relatively stable stages.

Infiltration characteristics of two instrumented residual soil slopes

2003 ◽  
Vol 40 (5) ◽  
pp. 1012-1032 ◽  
Author(s):  
Illias Tsaparas ◽  
Harianto Rahardjo ◽  
David G Toll ◽  
Eng-Choon Leong
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Field Measurements ◽  
Residual Soil ◽  
Rainfall Runoff ◽  
Rainfall Events ◽  
Pore Water Pressures ◽  
Soil Slopes ◽  
Pressure Changes

This paper presents the analysis of a 12 month long field study of the infiltration characteristics of two residual soil slopes in Singapore. The field measurements consist of rainfall data, runoff data of natural and simulated rainfall events, and pore-water pressure changes during infiltration at several depths and at several locations on the two slopes. The analysis of the field measurements identifies the total rainfall and the initial pore-water pressures within the two slopes as the controlling parameters for the changes in the pore-water pressures within the slopes during infiltration.Key words: infiltration, rainfall, runoff, pore-water pressure, field measurements.

Field measurement of anchor forces, ground temperatures, and pore-water pressures behind a retaining structure in northwestern Ontario

1992 ◽  
Vol 29 (1) ◽  
pp. 112-116
Author(s):  
K. D. Eigenbrod ◽  
J. P. Burak
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Retaining Wall ◽  
Field Measurements ◽  
Strain Gauges ◽  
Ground Temperatures ◽  
Northwestern Ontario ◽  
Pore Water Pressures ◽  
Load Increase

Anchor forces, ground temperatures, and piezometric pressures were measured at a retaining wall in northwestern Ontario over a period of 2 years. The anchor forces were measured with strain gauges attached in pairs directly to the anchor rods. This method appeared practical in the field for time periods of less than 2 years as long as the strain gauges were carefully protected against moisture. The anchor forces increased from an average of 5 kN initially up to values of 50 kN during the winter periods and dropped during the summer periods back to the same values measured initially. The anchor forces were largely independent of pore-water pressure variations behind the wall. Rapid drawdown conditions, however, which were experienced during the second summer, were reflected in a load increase that was equivalent to the associated unloading effect in front of the wall. The pore-water pressures behind the wall were not noticeably affected by rapid drawdown, possibly due to the restraining effect of the anchors and the high rigidity of the low sheet pile wall. Ground temperatures at or below the groundwater table never dropped below 0 °C thus restricting the depth of frost penetration. Key words : anchor loads, freezing pressure, retaining walls, pore-water pressures, ground temperatures, field measurements.

scholarly journals Mechanical response and pore pressure generation in granular filters subjected to uniaxial cyclic loading

2018 ◽  
Vol 55 (12) ◽  
pp. 1756-1768
Author(s):  
Jahanzaib Israr ◽  
Buddhima Indraratna
Keyword(s):  
Cyclic Loading ◽  
Pore Pressure ◽  
Pore Water ◽  
Mechanical Response ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Internal Erosion ◽  
Excess Pore Water Pressure ◽  
Excess Pore

This paper presents results from a series of piping tests carried out on a selected range of granular filters under static and cyclic loading conditions. The mechanical response of filters subjected to cyclic loading could be characterized in three distinct phases; namely, (I) pre-shakedown, (II) post-shakedown, and (III) post-critical (i.e., the occurrence of internal erosion). All the permanent geomechanical changes such, as erosion, permeability variations, and axial strain developments, took place during phases I and III, while the specimen response remained purely elastic during phase II. The post-critical occurrence of erosion incurred significant settlement that may not be tolerable for high-speed railway substructures. The analysis revealed that a cyclic load would induce excess pore-water pressure, which, in corroboration with steady seepage forces and agitation due to dynamic loading, could then cause internal erosion of fines from the specimens. The resulting excess pore pressure is a direct function of the axial strain due to cyclic densification, as well as the loading frequency and reduction in permeability. A model based on strain energy is proposed to quantify the excess pore-water pressure, and subsequently validated using current and existing test results from published studies.

Sign in / Sign up

Export Citation Format

Share Document