Mitigation of permanent deformation in base layer containing recycled asphalt aggregates

2013 ◽  
Vol 40 (2) ◽  
pp. 181-187 ◽  
Author(s):  
Jean-Pascal Bilodeau ◽  
Guy Doré ◽  
Jonas Depatie
Keyword(s):  
Asphalt Concrete ◽  
Deformation Behaviour ◽  
Permanent Deformation ◽  
Design Procedure ◽  
Base Layer ◽  
Repeated Loading ◽  
Recycled Asphalt ◽  
Thickness Increase ◽  
Permanent Strain ◽  
Pavement Base

The use of recycled asphalt pavement (RAP) aggregates as replacement for new materials in the pavement base weakens the layer in regards to the resistance to permanent deformation under repeated loading. A mechanistic based design procedure is proposed to ensure that base layers containing RAP particles have a similar rutting behaviour to base layers made of virgin aggregates. The design procedure allows calculating an asphalt concrete thickness increase that is based on permanent deformation behaviour of base materials. The calculation approach is based on multistage triaxial permanent deformation tests performed on granular material samples with varied RAP content. The tests allowed proposing an equation that relates permanent strain rate, RAP content, and deviatoric stress, which is the basis of the design procedure. Design charts are proposed to select adequate thickness increase for the asphalt concrete layer according to the expected RAP content in the base layer and asphalt concrete modulus.

scholarly journals Influence of Liquid Asphalt on Resilient Modules and Permanent Deformation of Recycled Asphalt Concrete

2019 ◽  
Vol 25 (9) ◽  
pp. 76-91
Author(s):  
Mohammed Chaloob Saleem AL-Shujairy ◽  
Saad Isaa Sarsam
Keyword(s):  
Asphalt Concrete ◽  
Resilient Modulus ◽  
Permanent Deformation ◽  
Water Bath ◽  
Repeated Loading ◽  
Recycled Asphalt ◽  
Average Value ◽  
Weight Content ◽  
Three Samples ◽  
Indirect Tensile

Tests were performed on Marshall samples and were implemented for permanent deformation and resilient modulus (Mr) under indirect tensile repeated loading (ITRL), with constant stress level. Two types of liquid asphalt (cutback and emulsion) were tried as recycling agents, aged materials that were reclaimed from field (100% RAP), samples were prepared from the aged mixture, and two types of liquid asphalt (cutback and emulsion) with a weight content of 0.5% were utilized to prepare a recycled mixture. A group of twelve samples was prepared for each mixture; six samples were tested directly for ITRL test (three samples at 25˚C and three samples at 40˚C), an average value for ITRL for every three samples was calculated (ITRL for unconditioned samples). The other six samples were placed in volumetric flask 4000-ml heavy- wall glass filled with water at 25˚C under a vacuum pressure of (3.74 kPa) for 5 to 10 minutes. Then the samples were put in deep freeze for 16 hours at -18˚C. The samples were frozen then were transported to a water bath at 60ºC for 24 hours. Then they were soaked in a water bath for 1 hour at 25ºC and tested for the ITRL test (three samples at 25˚C and three samples at 40˚C), the average value of ITRL for every three samples was calculated (ITRL for conditioned samples). It was concluded that the reduction in (Mr) at the Conditioned test as compared to the Unconditioned test was (29.5%, 22.27% and 9.09%) at 25˚C, while at 40˚C, the reduction was (21.28%, 15.53%, and 17.89%) for aged and recycled mixtures with (cutback), and (emulsion) respectively. The change in permanent deformation at the Conditioned test as compared to Unconditioned one was (76.19%, 75.61% and 53.22%) at 25˚C, while at 40˚C it was (56.48%, 35.19%, and 78.33%) for aged and recycled mixtures with (cutback), and (emulsion) respectively.  

scholarly journals Influence of Hydrated Lime on the Properties and Permanent Deformation of the Asphalt Concrete Layers in Pavement

2015 ◽  
Vol 4 (1) ◽  
pp. 1-19 ◽  
Author(s):  
Ahmed F. Al-Tameemi ◽  
Yu Wang ◽  
Amjad Albayati
Keyword(s):  
Asphalt Concrete ◽  
Raw Materials ◽  
Permanent Deformation ◽  
Fatigue Cracking ◽  
Hydrated Lime ◽  
Concrete Pavement ◽  
Partial Replacement ◽  
Repeated Loading ◽  
Concrete Mixtures ◽  
Asphalt Concrete Pavement

Abstract Flexible or asphalt concrete pavement is the paving system most widely adopted all over the world. It has been recognized that there are many different types of the factors affecting the performance and durability of asphalt concrete pavement, including the service conditions, such as: the variation of temperature from mild to extremes and the repeated excessive axle loading as well as the inadequate quality of the raw materials. All of these when combined together are going to accelerate the occurrence of distresses in flexible pavement such as permanent deformation and fatigue cracking. As the result, there has an urgent need to enhance the ability of asphalt concrete mixture to resist distresses happened in pavement. Use of additives is one of the techniques adopted to improve pavement properties. It has been found that hydrated lime might be one of the effective additives because it is widely available and relatively cheap compared to other modifiers like polymers. This paper presents an experimental study of the hydrated-lime modified asphalt concrete mixtures. Five different percentages of the hydrated lime additive were investigated, namely (1, 1.5, 2, 2.5 and 3 percent). The hydrated lime additive was used as partial replacement of limestone filler by total weight of the aggregate. The designed Hot Mix Asphalt (HMA) concretes are for the application of three pavement courses, i.e. Surface, Leveling and Base. These mixtures are designed and tested following Marshall procedure and uniaxial repeated loading to evaluate permanent deformation at different temperatures of 20°C, 40°C and 60°C. The experimental results show that the addition of hydrated lime as a partial replacement of ordinary limestone mineral filler results a significant improvement on mechanical properties and the resistant to permanent deformation of the designed asphalt concrete mixtures.

Performance Evaluations of Unbound Aggregate Permanent Deformation Models for Various Aggregate Physical Properties

2015 ◽  
Vol 2525 (1) ◽  
pp. 20-30 ◽  
Author(s):  
Yuanjie Xiao ◽  
Erol Tutumluer ◽  
Debakanta Mishra
Keyword(s):  
Physical Properties ◽  
Performance Indicator ◽  
Permanent Deformation ◽  
Model Parameters ◽  
Permanent Strain ◽  
Pavement Base ◽  
Materials Used ◽  
Low Sensitivity ◽  
Deformation Models ◽  
Unbound Aggregate

Permanent deformation or rutting is the main performance indicator of unbound aggregate layers used in flexible pavements. This paper evaluates the prediction abilities of unbound aggregate base or subbase permanent deformation models in use or proposed for use in the Mechanistic–Empirical Pavement Design Guide (MEPDG) approach. Repeated load triaxial-type permanent deformation tests were conducted on three unbound aggregate materials—limestone, dolomite, and uncrushed gravel—commonly used for pavement base and subbase and subgrade replacement applications in Illinois. The test matrix was designed to evaluate effects of aggregate physical properties, including moisture content, gradation, types and amounts of fines, aggregate mineralogy, and particle shape, texture, and angularity. The laboratory-measured permanent deformations were compared with those predicted by four rutting models evaluated in this study. The permanent deformations predicted by the original 1989 Tseng–Lytton model and the 2006 El-Badawy model were generally in good agreement with the measured values. The current MEPDG rutting model and its enhanced version proposed in 2013 by Hashem and Zapata tended to overpredict permanent deformations and have a low sensitivity to changes in aggregate physical properties. In addition to enhancements recommended for the four evaluated models, a unified rutting model was developed; it used a shear stress ratio concept and imaging-based aggregate morphological indexes. With a single set of calibrated model parameters, the unified rutting model produced reasonably accurate permanent strain predictions for all unbound aggregate materials used in this study.

scholarly journals Influence of Additives on Permanent Deformation and Resilient Modulus of Recycled Asphalt Concrete

2020 ◽  
Vol 26 (2) ◽  
pp. 159-175
Author(s):  
Mustafa Shakir Mahdi ◽  
Prof. saad Isa Sarsam
Keyword(s):  
Carbon Black ◽  
Compressive Stress ◽  
Asphalt Concrete ◽  
Resilient Modulus ◽  
Permanent Deformation ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Recycled Asphalt ◽  
Reclaimed Asphalt ◽  
Styrene Butadiene

Tests were performed on asphalt concrete specimens with (101.6 mm in diameter and 101.6 mm in height), and the results were implemented for calculating permanent deformation and resilient modulus under repeated compressive stress with different levels of stresses (0.068, 0.138 and 0.206) MPa at 40 ºC. Two types of additives namely (carbon black-asphalt) and (SBR-asphalt) were tried as rejuvenators with three percentages of (0.5, 1 and 1.5) % by weight of asphalt cement along with two ratios of AC (1 and 2) % have been implemented as rejuvenator and blended with the reclaimed asphalt concrete. Aged materials were obtained from the site. 100% Reclaimed Asphalt Pavement material from the reclaimed mixture is implemented. A set of (3) specimens were prepared for every mixture; three specimens were tested under (repeated compressive stress) at each level of stress. The objective of this work was to study the effect of two types of additives (Styrene-Butadiene-Rubber (SBR) and carbon black) on the performance of recycled asphalt concrete mixture. It was concluded that the Resilient modulus (Mr) at (0.138 and 0.206) MPa stress level decreases by (14, 22 and 8) % and (22, 34 and 11) for reclaimed and recycle mixtures with (carbon black-asphalt and SBR-asphalt) respectively when compared with that at 0.068 MPa. Permanent deformation for recycled mixtures with (carbon black-asphalt and SBR-asphalt) increased by (65.9, 4.54) %, (146.6, 27.2) % and (79, 5.5) % at level of stresses (0.068, 0.138 and 0.206) MPa respectively when compared to reclaimed mixture.

EXPERIENCE ON IMPLEMENTATION OF HOT IN-PLACE RECYCLING OF ASPHALT CONCRETE IN UKRAINE

2018 ◽  
pp. 28-36
Author(s):  
Vasyl Nagaychuk ◽  
Sergii Illiash ◽  
Tatyana Tereshchenko
Keyword(s):  
Asphalt Concrete ◽  
Surface Defects ◽  
Asphalt Pavement ◽  
Field Testing ◽  
Alternative Methods ◽  
Base Layer ◽  
Laboratory Evaluation ◽  
Recycled Asphalt ◽  
Pavement Rehabilitation ◽  
Road Pavement

Rehabilitation of asphalt concrete layers of road pavements using HIR technologies enables effective elimination of surface defects (rutting, cracking, raveling, bleeding (flushing)) including defects caused by the non-conformity of asphalt concrete to the standard specifications. Due to the economical and ecological advantages, HIR technologies belong to the present-day effective alternative methods of rehabilitation of asphalt concrete pavements. In Ukraine, HIR technologies were first applied on intermediate repair works on an area of the international road I-01 “Kyiv-Chernihiv-Novyye Yarylovichi” in the 2013. Now, HIR technologies have been applied on repair works on numerical objects including areas on such state motor roads as I-01, I-06, N-09, R-10, R-67. The presented paper analyzes the results of monitoring of materials and technologies which was aimed on HIR performance investigation supported by State Road Agency of Ukraine (Ukravtodor) throughout 2014-2018. The results of monitoring of HIR technologies including laboratory evaluation of materials and also field testing of the rehabilitated pavements led to the conclusions fitted by the world-wide experience on implementation of HIR technologies. 1. Being applied to the structurally sound pavements, HIR provides effective elimination of surface defects of flexible pavement to a depth of (50-60) mm including defects caused by the non-conformity of asphalt concrete to the standard specifications. However, HIR is not suitable for existing asphalt pavements which have too much variation in asphalt concrete composition and thickness within the project limits. 2. The efficiency of asphalt pavement rehabilitation using HIR technologies largely depends on precise engineering consideration which determines the efficiency of preparatory (repair) works including some special works such as: – correction of cracks in case of cracking that extends below the depth of hot recycling; – re-compaction of an unbound base layer(s) in case of the insufficient compaction causing “alligatored” network-like cracking of asphalt pavement. 3. Proper technical and working conditions of the rehabilitated pavement during the nominal life cycle could be maintained by overlaying the surface treatment using bituminous emulsion materials or by single-pass overlaying a new hot-mixed asphalt concrete layer. Investigations accomplished during the implementation of HIR technologies allow enhance quality of recycled materials and also promote the entire adaptation of HIR technologies to the Ukrainian standards. Keywords: asphalt pavement rehabilitation, hot in-place recycling, recycled asphalt concrete, field testing, road pavement strength measurement, rutting measurement.

Influences on Permanent Deformation Behavior of Unbound Granular Materials

1996 ◽  
Vol 1547 (1) ◽  
pp. 68-75 ◽  
Author(s):  
Fredrick Lekarp ◽  
Ian Reginald Richardson ◽  
Andrew Dawson
Keyword(s):  
Granular Materials ◽  
Stress Level ◽  
Deformation Behavior ◽  
Permanent Deformation ◽  
Repeated Loading ◽  
Permanent Strain ◽  
Unbound Granular Materials ◽  
Failure Line ◽  
Static Failure ◽  
French Model

The results of a research program aimed at characterizing the permanent deformation behaviors of different types of unbound aggregates under repeated loading are summarized. Tests were performed in a triaxial or hollow-cylinder apparatus, depending on the grading of the materials. The scope of the research was to assess the relationship between total permanent axial strain and both the number of load applications and the stress level. The test results were used to verify a model recently developed in France in which attempts are made to predict the long-term behaviors of granular materials. The French model is examined with particular reference to its validity on the effect of stress level on permanent deformation of unbound granular materials. The results of the study indicate that the French model is generally successful in predicting the permanent strain for a given number of load applications. For one of the materials, however, the model did not seem to fit the data well. The French model also suggests that the variation in total permanent strain with stress level is related to the static failure line and could be determined by comparing the maximum shear stress ratio with the slope of the estimated failure line. This is discussed and shown to be questionable because it results in either unreasonable failure parameters or a very low level of correlation with the observations. An attempt was made to modify the French model, but that also proved to be unsuccessful. The concept of relating the permanent deformation behavior to the static failure condition of the material is therefore questioned.

Sign in / Sign up

Export Citation Format

Share Document