Rheological modelling of masonry creepThis article is one of a selection of papers published in this Special Issue on Masonry.

2007 ◽  
Vol 34 (11) ◽  
pp. 1506-1517 ◽  
Author(s):  
Kyoung-Kyu Choi ◽  
Shelley L. Lissel ◽  
Mahmoud M. Reda Taha
Keyword(s):  
Stress Level ◽  
Rheological Model ◽  
Creep Behaviour ◽  
Model Development ◽  
Sustained Load ◽  
Creep Tests ◽  
Standard Type ◽  
Rheological Models ◽  
Proposed Model ◽  
Rheological Modelling

In the present study, masonry creep was experimentally investigated. Creep tests were performed on masonry prisms, which were produced using standard fired clay brick and standard Type S mortar. A total of 11 sets of loaded and unloaded masonry specimens were tested under sustained load with three main parameters: stress level, masonry age at loading, and relative humidity. The unloaded prisms compensated for the effects of shrinkage. In this article, the ability of a number of rheological models reported in the literature are examined for their ability to predict masonry creep. Moreover, a new rheological model, one that considers the effect of stress level and masonry age at loading, is proposed. The system parameters of the proposed model were identified using the experimental data. The proposed model was then validated using masonry creep data that was reported by other researchers, but not used in model development. It is shown that the creep behaviour of masonry can be modelled with good accuracy using the proposed rheological model.

scholarly journals Creep Behavior of Intact Loess Followed Unloading Paths

2021 ◽  
Vol 9 ◽  
Author(s):  
Zhenxiao Li ◽  
Jiading Wang ◽  
Dengfei Zhang
Keyword(s):  
Stress Level ◽  
Progressive Failure ◽  
Axial Stress ◽  
Deep Understanding ◽  
Confining Pressure ◽  
Axial Deformation ◽  
Creep Tests ◽  
Proposed Model ◽  
Good Comparison ◽  
Intact Loess

Several high-fill projects are carried out on the Loess Plateau, China, accompanying the progressive failure of slopes due to excavation. The compelling need requires a deep understanding of variation in the creeping behaviors of intact loess exposed to unloading. A series of creep tests of intact loess were performed under two separated unloading paths: decrease in confining pressure at constant deviator stress and decrease in confining pressure at axial stress. The results demonstrated that axial deformation followed the first unloading path always appears as compression while the three forms of axial deformation followed the second path, depending on the applied axial stress level. At a low unloading stress level, the elongation of axial deformation was observed. At a relatively unloading stress level, the axial deformation of the soil experienced the first elongation and then compression. At a high unloading stress level, the axial deformation appeared as compression, and finally, failure occurred with the increase of the unloading stress level. The failure approach index was introduced to use as the criterion for the loess to transform from stable to accelerated creeping. Finally, a modified Burgers model was proposed to characterize the creeping behavior of intact loess followed unloading paths. There was a good comparison between the calculated and measured data of the soil that establishes the rationality and validity of the proposed model.

scholarly journals Multi-Layer Blockchain-Based Security Architecture for Internet of Things

Sensors ◽  
2021 ◽  
Vol 21 (3) ◽  
pp. 772 ◽  
Author(s):  
Houshyar Honar Pajooh ◽  
Mohammad Rashid ◽  
Fakhrul Alam ◽  
Serge Demidenko
Keyword(s):  
Internet Of Things ◽  
Clustering Algorithm ◽  
Model Development ◽  
Base Stations ◽  
Smart Devices ◽  
Security Model ◽  
Cluster Heads ◽  
Authentication Mechanism ◽  
Proposed Model ◽  
Authentication And Authorization

The proliferation of smart devices in the Internet of Things (IoT) networks creates significant security challenges for the communications between such devices. Blockchain is a decentralized and distributed technology that can potentially tackle the security problems within the 5G-enabled IoT networks. This paper proposes a Multi layer Blockchain Security model to protect IoT networks while simplifying the implementation. The concept of clustering is utilized in order to facilitate the multi-layer architecture. The K-unknown clusters are defined within the IoT network by applying techniques that utillize a hybrid Evolutionary Computation Algorithm while using Simulated Annealing and Genetic Algorithms. The chosen cluster heads are responsible for local authentication and authorization. Local private blockchain implementation facilitates communications between the cluster heads and relevant base stations. Such a blockchain enhances credibility assurance and security while also providing a network authentication mechanism. The open-source Hyperledger Fabric Blockchain platform is deployed for the proposed model development. Base stations adopt a global blockchain approach to communicate with each other securely. The simulation results demonstrate that the proposed clustering algorithm performs well when compared to the earlier reported approaches. The proposed lightweight blockchain model is also shown to be better suited to balance network latency and throughput as compared to a traditional global blockchain.

122 A Mechanistic Model of Growth and Amino Acid Deposition in the Pregnant Sow: Model Development, Evaluation, and Application

2021 ◽  
Vol 99 (Supplement_1) ◽  
pp. 55-56
Author(s):  
Christian D Ramirez-Camba ◽  
Crystal L Levesque
Keyword(s):  
Weight Gain ◽  
Amino Acid ◽  
Mechanistic Model ◽  
Model Development ◽  
Allantoic Fluid ◽  
Late Gestation ◽  
Maternal Body ◽  
Proposed Model ◽  
Development Evaluation ◽  
Model Weight

Abstract A mechanistic model was developed with the objective to characterize weight gain and essential amino acid (EAA) deposition in the different tissue pools that make up the pregnant sow: placenta, allantoic fluid, amniotic fluid, fetus, uterus, mammary gland, and maternal body were considered. The data used in this modelling approach were obtained from published scientific articles reporting weights, crude protein (CP), and EAA composition in the previously mentioned tissues; studies reporting not less than 5 datapoints across gestation were considered. A total of 12 scientific articles published between 1977 and 2020 were selected for the development of the model and the model was validated using 11 separate scientific papers. The model consists of three connected sub-models: protein deposition (Pd) model, weight gain model, and EAA deposition model. Weight gain, Pd, and EAA deposition curves were developed with nonparametric statistics using splines regression. The validation of the model showed a strong agreement between observed and predicted growth (r2 = 0.92, root mean square error = 3%). The proposed model also offered descriptive insights into the weight gain and Pd during gestation. The model suggests that the definition of time-dependent Pd is more accurately described as an increase in fluid deposition during mid-gestation coinciding with a reduction in Pd. In addition, due to differences in CP composition between pregnancy-related tissues and maternal body, Pd by itself may not be the best measurement criteria for the estimation of EAA requirement in pregnant sows. The proposed model also captures the negative maternal Pd that occurs in late gestation and indicates that litter size influences maternal tissue mobilization more than parity. The model predicts that the EAA requirements in early and mid-gestation are 75, 55 and 50% lower for primiparous sows than parity 2, 3 and 4+ sows, respectively, which suggest the potential benefits of parity segregated feeding.

Effect of Equal-Channel Angular Pressing (ECAP) on Creep in Aluminium Alloys

2007 ◽  
Vol 539-543 ◽  
pp. 2904-2909 ◽  
Author(s):  
Vàclav Sklenička ◽  
Jiří Dvořák ◽  
Marie Kvapilová ◽  
Milan Svoboda ◽  
Petr Král ◽  
...  
Keyword(s):  
Equal Channel Angular Pressing ◽  
Aluminium Alloys ◽  
Creep Resistance ◽  
Room Temperature ◽  
Creep Behaviour ◽  
Coarse Grained ◽  
Pure Aluminium ◽  
Creep Tests ◽  
Angular Pressing ◽  
Compression Creep

This paper examines the effect of equal-channel angular pressing (ECAP) on creep behaviour of pure aluminium, binary Al-0.2wt.%Sc alloy and ternary Al-3wt.%Mg-0.2wt.%Sc alloy. The ECAP was conducted at room temperature with a die that had a 90° angle between the channels and 8 repetitive ECAP passes followed route BC. Constant stress compression creep tests were performed at 473 K and stresses ranging between 16 to 80 MPa on ECAP materials and, for comparison purposes, on the initial coarse-grained materials. The results showed that the creep resistance of the ECAP processed Al-Sc and Al-Mg-Sc alloys was markedly deteriorated with respect to unpressed coarse-grained materials.

Modelling of Flow Properties of Asphalt Mastics

2013 ◽  
Vol 752 ◽  
pp. 209-216 ◽  
Author(s):  
Róbert Géber ◽  
László A. Gömze
Keyword(s):  
Research Work ◽  
Road Construction ◽  
Test Results ◽  
Flow Properties ◽  
Rheological Models ◽  
Fine Grained ◽  
Mineral Particles ◽  
Asphalt Mastics ◽  
Rheological Modelling ◽  
Mineral Fillers

The present research work deals with the examination and rheological modelling of flow properties of asphalt mastics which are the most important components of asphalt concretes. Asphalt mastics are mixtures of fine grained mineral filler particles (d<0,063 mm) and bitumen, having a stabilizing role in asphalt mixtures and largely determining the cohesion between mineral particles and bitumen. During our examinations two types of mineral fillers – limestone and dolomite – as well as standard bitumen were tested, which are extensively used in Hungarian road construction. Asphalt mastic mixtures were prepared out of these materials and they were tested with dynamic shear rheometer (DSR). According to the test results, rheological models of mastics were determined. It has been established that at different test temperatures and shear rate ranges asphalt mastics behave as Herschel-Bulkley and Bingham-type materials.

scholarly journals Creep Behaviour and Microstructural Characterization of VAT 36 and VAT 32 Superalloys

Metals ◽  
2018 ◽  
Vol 8 (11) ◽  
pp. 877 ◽  
Author(s):  
Vagner Gobbi ◽  
Silvio Gobbi ◽  
Danieli Reis ◽  
Jorge Ferreira ◽  
José Araújo ◽  
...  
Keyword(s):  
Failure Analysis ◽  
Creep Resistance ◽  
High Performance ◽  
Creep Behaviour ◽  
Ductile Failure ◽  
Microstructural Characterization ◽  
Dislocation Slip ◽  
Creep Tests ◽  
Experimental Conditions ◽  
Wide Range

Superalloys are used primarily for the aerospace, automotive, and petrochemical industries. These applications require materials with high creep resistance. In this work, evaluation of creep resistance and microstructural characterization were carried out at two new nickel intermediate content alloys for application in aerospace industry and in high performance valves for automotive applications (alloys VAT 32 and VAT 36). The alloys are based on a high nickel chromium austenitic matrix with dispersion of intermetallic L12 and phases containing different (Nb,Ti)C carbides. Creep tests were performed at constant load, in the temperature range of 675–750 °C and stress range of 500–600 MPa. Microstructural characterization and failure analysis of fractured surfaces of crept samples were carried out with optical and scanning electron microscopy with EDS. Phases were identified by Rietveld refinement. The results showed that the superalloy VAT 32 has higher creep resistance than the VAT 36. The superior creep resistance of the alloy VAT 32 is related to its higher fraction of carbides (Nb,Ti)C and intermetallic L12 provided by the amount of carbon, titanium, and niobium in its chemical composition and subsequent heat treatment. During creep deformation these precipitates produce anchoring effect of grain boundaries, hindering relative slide between grains and therefore inhibiting crack formation. These volume defects act also as obstacles to dislocation slip and climb, decreasing the creep rate. Failure analysis of surface fractures of crept samples showed intergranular failure mechanism at crack origin for both alloys VAT 36 and VAT 32. Intergranular fracture involves nucleation, growth, and subsequent binding of voids. The final fractured portion showed transgranular ductile failure, with dimples of different shapes, generated by the formation and coalescence of microcavities with dissimilar shape and sizes. The occurrence of a given creep mechanism depends on the test conditions. At creep tests of VAT 32 and VAT 36, for lower stresses and higher temperature, possible dislocation climb over carbides and precipitates would prevail. For higher stresses and intermediate temperatures shear mechanisms involving stacking faults presumably occur over a wide range of experimental conditions.

scholarly journals Biopolymer Drill-in Fluid Performance for Different Rheological Models using Statistical Characterisation

2019 ◽  
Vol 19 (1) ◽  
pp. 86-92
Author(s):  
M. Owusu ◽  
H. Osei
Keyword(s):  
Rheological Model ◽  
Rheological Behaviour ◽  
Primary Objective ◽  
Least Square ◽  
Model Parameters ◽  
Drilling Fluids ◽  
Cleaning Efficiency ◽  
Rheological Models ◽  
Least Square Regression ◽  
Best Fit

Appropriate selection of rheological models is important for hydraulic calculations of pressure loss prediction and hole cleaning efficiency of drilling fluids. Power law, Bingham-Plastic and Herschel-Bulkley models are the conventional fluid models used in the oilfield. However, there are other models that have been proposed in literature which are under/or not utilized in the petroleum industry. The primary objective of this paper is to recommend a rheological model that best-fits the rheological behaviour of xanthan gum-based biopolymer drill-in fluids for hydraulic evaluations. Ten rheological models were evaluated in this study. These rheological models have been posed deterministically and due to the unrealistic nature have been replaced by statistical models, by adding an error (disturbance) term and making suitable assumptions about them. Rheological model parameters were estimated by least-square regression method. Models like Sisko and modified Sisko which are not conventional models in oil industry gave a good fit. Modified Sisko model which is a four parameter rheological model was selected as the best-fit model since it produced the least residual mean square of 0.61 Ibf2/100ft4. There is 95% certainty that the true best-fit curve lies within the confidence band of this function of interest. Keywords: Biopolymer; Least-Square Regression; Residual Mean Squares; Rheologram

Creep Behavior of a Solder Paste With Bi Addition

2017 ◽  
Author(s):  
Pedro E. Ribeiro ◽  
Delfim F. Soares ◽  
Maria F. Cerqueira ◽  
Senhorinha F. Teixeira ◽  
Daniel A. Barros ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Solder Joint ◽  
Mechanical Performance ◽  
Creep Behaviour ◽  
Real Life ◽  
Production Costs ◽  
Solder Paste ◽  
Creep Tests ◽  
Pcb Assembly ◽  
Solder Joint Fatigue

A common failure mode of electronic PCB’s is the appearance of cold solder joints between the component and PCB, during product life. This phenomenon is related to solder joint fatigue and is attributed mainly to the mismatch of the coefficients of thermal expansion (CTE) of component-solder-PCB assembly. Although some experiments show that newer lead-free tin-silver-copper (Sn-Ag-Cu, or SAC) solders perform better than the older SnPb ones, with today’s solder joint thickness decreasing and increasing working temperatures, among others, the stresses and strains due to temperature changes are growing, leading to limited fatigue life of the products. As fatigue life decreases with increasing plastic strain, creep occurrence should have significant impact, especially during thermal cycles. In order to improve mechanical properties, but also as an attempt to reduce maximum reflow cycle temperatures due to component damage and production costs, various SAC solder alloying additives are being considered to use in industrial production facilities. Solder paste producers are proposing new products based on new solder paste formulations, but the real life effects on thermo-mechanical performance aren’t well known at the moment. In this paper a dynamic mechanical analyser (DMA) is used to study the influence of Bismuth (Bi) addition, up to 5 wt %, on SAC405 solder paste, in terms of creep behaviour. Creep tests were made on three-point-bending configuration, isothermally at 30 °C, 50 °C and 75 °C, and three different stresses of 3, 5 and 9 MPa. The results shown not only a significant Bi concentration influence on creep behaviour but also a noticeable temperature dependence.

Influence of the Applied Load on the Creep Behaviour of Tin-Silver-Copper Solder

2019 ◽  
Author(s):  
Delfim F. Soares ◽  
Pedro E. Ribeiro ◽  
Pauline Capela ◽  
Daniel A. Barros ◽  
Maria F. Cerqueira ◽  
...  
Keyword(s):  
Fatigue Life ◽  
Solder Joint ◽  
Applied Load ◽  
Printed Circuit Boards ◽  
Creep Behaviour ◽  
Creep Tests ◽  
Dislocation Glide ◽  
Pcb Assembly ◽  
Creep Mechanisms ◽  
Solder Joint Fatigue

Abstract During the life cycle of an electronic printed circuit boards (PCBs), the cold solder joints formation between the component and PCB are a failure mode that happen commonly. This phenomenon is related to solder joint fatigue and is attributed mainly to the mismatch of the coefficients of thermal expansion (CTE) of component-solder-PCB assembly. With today’s solder joint thickness decreasing and increasing working temperatures, among others, the stresses and strains due to temperature changes are growing, leading to limited fatigue life of the products. In this way, once as fatigue life decreases with increasing plastic strain, it is important to study creep occurrence, especially during thermal cycles. In this work, a dynamic mechanical analyser (DMA) was used to study the influence of different applied load and temperature on the creep behaviour of the solder during a sequence of cycles. For these tests, different SAC405 alloy samples were produced, all in the same processing conditions. Creep tests were made on three-point-bending clamp configuration, isothermally at 303, 323 and 348 K, under three separate applied load of 3, 5 and 9 MPa. The results show that creep rate has an important decrease from the 1st to the following applied creep cycles. This behaviour occurs for all the tested loads and temperatures. Results, also, show that the main creep mechanisms changes, from a diffusion base type, for low load and different temperatures, to a dislocation glide-climb type for an applied load of 9 MPa and temperatures from 303 to 348 K. Experimental determined n exponent for the tested conditions allows the correlation between creep mechanisms and experimental parameters (applied load and temperature).

Long Term Creep Life Prediction of New and Service Exposed P91 Steel

2018 ◽  
Author(s):  
Muneeb Ejaz ◽  
Norhaida Ab Razak ◽  
Andrew Morris ◽  
Scott Lockyer ◽  
Catrin M. Davies
Keyword(s):  
Tensile Strength ◽  
Creep Behaviour ◽  
Equivalent Stress ◽  
Practical Reasons ◽  
Creep Data ◽  
Short Term ◽  
Creep Tests ◽  
High Temperature Components ◽  
Term Creep

P91 steels are widely used in high temperature components for power generation. Creep data is often generated through accelerated short term creep tests, for practical reasons, via increasing stress or temperature though this may alter the creep behaviour. Through normalising the creep test stress by tensile strength the Wilshire models reduce the batch to batch scatter in the creep data and enable the prediction of long term creep data from relatively short term test results. In this work it is shown that the Wilshire models fitted to uniaxial creep rupture data can be used to predict failure in both as cast and service exposed multiaxial tests. This is provided that the equivalent stress is the rupture controlling stress, as is the case for the P91 tests examined, and the tensile strength is measured as part of the test programme.

Sign in / Sign up

Export Citation Format

Share Document