Understanding the Effect of Reflow Profile on the Metallurgical Properties of Tin–Bismuth Solders

Sn–Bi alloys are desirable candidates for soldering components on printed circuit boards (PCBs) because of their low melting point and reduced cost. While certain tin–bismuth solders are well characterized many new alloys in this family have been developed which need proper characterization. The following study looks at the behavior of four different Sn–Bi alloys—traditional 42Sn58Bi and 42Sn57Bi1Ag and two new tin–bismuth alloys—in solder paste during the reflow soldering process. Each alloy was processed using different reflow profiles that had varying times above liquidus (TALs) and peak temperatures. The PCBs were then analyzed to see how the processing variables influenced wetting, voiding, microstructure, intermetallic layer composition, and thickness. After analysis, the PCBs were then subjected to thermal cycling experiments to see how reflow profile impacted microstructure evolution. The results demonstrated that reflow profile affects properties such as metal wetting and voiding. It does not however, greatly impact key metallurgical properties such as intermetallic layer thickness.

Investigation of solder beading phenomenon under surface-mounted electrolytic capacitors

Purpose The purpose of this paper is to study the solder beading phenomenon (referring to larger-sized solder balls) of surface-mounted electrolytic capacitors. Solder beading could induce failures by violating the minimal electrical clearance on the printed circuit board (PCB). In modern lead-free reflow soldering, especially in high-reliability industries, such as automotive, aeroplane and aerospace, detecting and preventing such defects is essential in reliable and cost-effective manufacturing. Design/methodology/approach The large size of the involved components may block the view of automatic optical inspection; therefore, X-ray inspection is necessary. To detect the failure mode, X-ray imaging, cross-section grinding, optical microscopy and Fourier transformed infrared spectroscopy were used. High-resolution noncontact profilometry and optical microscopy were used to analyse component designs. The surface mounting process steps were also analysed to reveal their dependence on the issue. Test methods were designed and performed to reveal the behaviour of the solder paste (SP) during the reflow soldering process and to emphasise the component design relevance. Findings It was found that the reduction of SP volume only reduces the failure rate but does not solve the problem. Results show that excessive component placement pressure could induce solder beading. Statistical analysis revealed that differences between distinct components had the highest effect on the solder beading rate. Design aspects of solder beading-prone components were identified and discussed as the primary source of the problem. Practical implications The findings can be applied in surface-mount technology production, where the total failure count and resulting failure costs could be reduced according to the findings. Originality/value This paper shows that component design aspects such as the low distance between the underside of the component and the PCB and blocked proper outgassing of volatile compounds of the SP can be root causes of solder beading under surface-mounted electrolytic capacitors.

Laser-Induced Period Surface Structures to Improve Solderability of Electrical Solder Pads

We report on structuring copper representing soldering pads of printed circuit boards by laser-induced periodic surface structures. Femtosecond laser radiation is used to generate low spatial frequency laser-induced surface structures, having a spatial period of 992 nm and a modulation depth of 120 nm, respectively. The slump of screen-printed solder paste is measured to compare the solder coverage on the pads after the solder process on a hot plate. A comparative study of the coverage of solder paste on a fresh polished pad, a pad stored for two weeks, and femtosecond laser-structured pads reveals the improved wettability of structured pads even after storage. In addition, leaded and lead-free solder pads are compared with the particular advantages of the solder-free pad when periodically laser structured. Our findings are attributed to two major effects: namely, the increase of the surface area and the improved surface chemical wettability. Overall, the application of laser-induced periodic surface structures helps to reduce the demand of lead-based solder in the electronic industry and provides a feasible method for a fast and spatial selective way of surface functionalization.

Influence of Flux and Related Factors on Intermetallic Layer Growth within SAC305 Solder Joints

Flux contained in solder paste significantly affects the process of solder joint creation during reflow soldering, including the creation of an intermetallic layer (IML). This work investigates the dependence of intermetallic layer thickness on ROL0/ROL1 flux classification, glossy or matt solder mask, and OSP/HASL/ENIG soldering pad surface finish. Two original SAC305 solder pastes differing only in the used flux were chosen for the experiment. The influence of multiple reflows was also observed. The intermetallic layer thicknesses were obtained by the image analysis of micro-section images. The flux type proved to have a significant impact on the intermetallic layer thickness. The solder paste with ROL1 caused an increase in IML thickness by up to 40% in comparison to an identical paste with ROL0 flux. Furthermore, doubling the roughness of the solder mask has increased the resulting IML thickness by 37% at HASL surface finish and by an average of 22%.

Rheologically Assisted Design of Conductive Adhesives for Stencil Printing on PCB

Driven by the need to deliver new, lead-free, eco-friendly solder pastes for soldering electronic components to Printed Circuit Boards (PCB), electrically conductive adhesives (ECAs) based on epoxy, carbon nanotubes (CNT), and exfoliated graphite (EG) were designed. The rheology of the adhesives prepared is paramount for the success of the deposition process, which is based on stencil printing. Thus, a rheological analysis of the process was first performed. Then, an experimental protocol was defined to assess the relevant viscoelastic characteristics of the adhesives for stencil printing application. Different composite formulations of epoxy/CNT/EG were produced. Their rheological characteristics were established following the designed protocol and benchmarked with a commercial solder paste. The thermal and electrical properties of the composite formulations were also characterized. As a result, a new, electrically conductive adhesive was delivered with potential to be an eco-friendly alternative to the solder paste currently used in stencil printing of PCB.

Contact Angle Measurement of Melting SnAgCu Solder Paste Mix with Carbon Allotropes Using In-Line Digital Holography Technique

In this research we investigated the contact angle of commercial SnAgCu solder paste mixing with some carbon allotropes such as graphite, graphene quantum dots, and fullerene of varying concentrations with melting temperature, wettability, interfacial microstructure. The wettability was assessed in terms of the contact angle. The in-line digital holography was used for determining the contact angle and morphological of samples at each temperature which the samples have been heating from room temperature until the melting temperature. In the experiment, only one beam was used as the object and reference beams which recorded by a CMOS camera. The recorded image was reconstructed by the angular spectrum digital holography numerical programing. Using the reconstructed images of our results, the shape and contact angle of solder pastes can be investigated.

Effects of Different Viscometer Test on Stencil Printing Process for CFD Simulation

This study discusses the use of different spindle type for the testing of lead-free solder paste by using Computational Fluid Dynamics (CFD) simulation. The study focuses on measuring the volume of solder paste deposition on the solder pad. Parallel-plate (PP) and Cone-plate (CP) spindle were used with five different tests consist of different spindle type and setting. The Volume of Fluid (VOF) method was used for the simulation while Cross model was applied as viscosity model for the solder paste. SAC305 type 3 lead-free solder paste was used in this study as it is mostly popular used by the industries nowadays. The solder paste filled the volume under different squeegee speeds and aperture size was compared between experiments and simulations. For different squeegee speed, PP 0.5 mm gap obtained the lowest average discrepancy value between simulation and experimental results. At different aperture size, all test show similar trend line and about the same value of average discrepancy with CP1° while PP 0.5 mm gap showed the lowest average discrepancy. At small aperture volume, all tests performed shows similar value of filled volume except PP 0.5 mm which exhibit the lowest percentage difference when compared with the experimental values at a bigger aperture volume.