Evaluation of base shear provisions in the 1985 edition of the National Building Code of Canada

1989 ◽  
Vol 16 (1) ◽  
pp. 22-35 ◽  
Author(s):  
T. J. Zhu ◽  
W. K. Tso ◽  
A. C. Heidebrecht
Keyword(s):  
Yield Strength ◽  
Seismic Response ◽  
Structural Damage ◽  
Ground Motions ◽  
Response Spectra ◽  
Building Code ◽  
Base Shear ◽  
Response Factors ◽  
Period Range ◽  
Short Period

A statistical analysis is performed to evaluate the base shear provisions in the 1985 edition of the National Building Code of Canada (NBCC 1985). Three sets of real earthquake records are selected to represent seismic ground motions with low, normal, and high peak acceleration to velocity (a/v) ratios. Single degree of freedom stiffness degrading systems are used as structural models; three damage indicators are employed to measure structural damage. The yield strength of the systems is specified in two different ways: (a) a single seismic response factor is used, irrespective of the a/v ratios of the input ground motions; (b) three different seismic response factors are used in the short-period range, depending upon the a/v ratios of the input ground motions, as suggested in NBCC 1985. A comparison of the statistical results of the three damage parameters for the systems designed with these two methods of strength specification indicates that the NBCC 1985 base shear provisions provide consistent control over structural damage when the structural systems are subjected to ground motions with different a/v ratios. Key words: earthquakes, ground motions, response spectra, stiffness degrading systems, seismic design, base shear, yield strength, inelastic response, damage parameters.

Combined seismic base shear and torsional loading provisions in the 1990 edition of the National Building Code of Canada

1991 ◽  
Vol 18 (6) ◽  
pp. 945-953
Author(s):  
A. M. Chandler
Keyword(s):  
Ground Motions ◽  
Building Code ◽  
Soil Conditions ◽  
Building Structures ◽  
Base Shear ◽  
Ground Acceleration ◽  
Period Range ◽  
Natural Period ◽  
Short Period ◽  
Edge Response

This paper evaluates the earthquake-resistant design provisions of the 1990 edition of the National Building Code of Canada (NBCC 1990) for asymmetric building structures subjected to combined lateral shear and torsional dynamic loadings arising from earthquake base excitation. A detailed parametric study is presented, evaluating the dynamic edge displacement response in the elastic range, for the side of the building which is adversely affected by lateral–torsional coupling. A series of buildings is studied, with realistic ranges of the fundamental natural period, structural eccentricity, and uncoupled frequency ratio. These buildings are evaluated under base loadings arising from a total of 45 strong motion records taken from earthquakes in North America, Mexico, Europe, the Middle East, and Southern Pacific, categorized according to site soil conditions and the ratio a/v of peak ground acceleration to velocity. The latter parameter together with the uncoupled lateral period are found to influence strongly the combined dynamic edge response, with the greatest forces on edge members arising from earthquakes with high a/v ratio in structures with natural periods below 0.8 s. In this case the NBCC 1990 loading provisions significantly underestimate the elastic dynamic response. For buildings with periods longer than 0.8 s, the conservatism of the base shear provisions leads to overestimation of combined dynamic edge response in asymmetric systems, and this is also true in the short-period range for buildings subjected to ground motions with low a/v ratio. The NBCC 1990 provisions are reasonably conservative for short-period systems subjected to ground motions with intermediate a/v ratio. Key words: earthquakes, seismic, design, response, spectra, base, shear, torsional, provisions.

Significance of Ground Motion Scaling Parameters on Amplitude of Scale Factors and Seismic Response of Short- and Long-Period Structures

2019 ◽  
Vol 35 (4) ◽  
pp. 1663-1688 ◽  
Author(s):  
Esengul Cavdar ◽  
Gokhan Ozdemir ◽  
Beyhan Bayhan
Keyword(s):  
Seismic Response ◽  
Ground Motion ◽  
Ground Motions ◽  
Response Spectra ◽  
Scaling Method ◽  
Period Range ◽  
Long Period ◽  
Scale Factors ◽  
Short Period ◽  
Response History Analysis

In this study, an ensemble of ground motions is selected and scaled in order to perform code-compliant bidirectional Nonlinear Response History Analysis for the design purpose of both short- and long-period structures. The followed scaling method provides both the requirements of the Turkish Earthquake Code regarding the scaling of ground motions and compatibility of response spectra of selected ground motion pairs with the target spectrum. The effects of four parameters, involved in the followed scaling method, on both the amplitude of scale factors and seismic response of structures are investigated. These parameters are the number of ground motion records, period range, number of periods used in the related period range, and distribution of weight factors at the selected periods. In the analyses, ground motion excitations were applied to both fixed-base and seismically isolated structure models representative of short- and long-period structures, respectively. Results revealed that both the amplitudes of scale factors and seismic response of short-period structures are more prone to variation of investigated parameters compared to those of long-period structures.

Influence of site effects and period-dependent force modification factors on the seismic response of ductile structures

1994 ◽  
Vol 21 (4) ◽  
pp. 596-604 ◽  
Author(s):  
Shamel Hosni ◽  
Arthur C. Heidebrecht
Keyword(s):  
Seismic Response ◽  
Site Effects ◽  
Ground Motions ◽  
Code Design ◽  
Base Shear ◽  
Engineering Structures ◽  
Local Soil ◽  
Short Period ◽  
Modification Factor ◽  
Ductility Capacity

A foundation factor, F, is incorporated in the National Building Code of Canada (NBCC) design base shear formula to account for amplification of bedrock ground motions as these propagate upwards through the local soil deposit (site effects). In the NBCC, the value of F is specified as a function of the local soil type and depth, irrespective of the ductility capacity for which the structure situated at the surface of the soil deposit is to be designed and detailed. On the other hand, the ductility capacity of the structures is taken into account in the code by the force modification factor, R, for which values are specified depending on the type of the structural system. The current study investigates the influence of the ductility capacity of engineering structures in mitigating the site effects. Simple bilinear single-degree-of-freedom models are used to simulate the seismic response of structures, underlain by soft or stiff soil deposits and subjected to seismic ground motions. These structural models are also used to investigate the effects of the period-dependent force modification factors on the seismic response of structures.The results show that site effects are less significant for ductile structures, as compared with structures that respond elastically. The results are then used to evaluate the current code provisions for site effects. The current study also shows that using period-dependent force modification factors to derive the code design base shear not only is recommended for short period structures but also is necessary to provide a realistic simulation of the seismic response of these structures. Key words: site, seismic, ductility, structure, foundation, factor, base, shear, amplification, soil, period.

The Vertical and Horizontal Spectra of Near-Fault Ground Motions

2012 ◽  
Vol 204-208 ◽  
pp. 3335-3339
Author(s):  
Jiang Yin ◽  
Xian Yan Zhou ◽  
Guo Jing He
Keyword(s):  
Ground Motions ◽  
Response Spectra ◽  
Vertical Acceleration ◽  
Period Range ◽  
Seismic Reliability ◽  
Design Spectrum ◽  
Near Fault ◽  
Seismic Design Code ◽  
Short Period ◽  
Near Fault Earthquakes

Based on the horizontal and vertical components of a set of 30 acceleration records obtained from 10 near-fault earthquakes, the horizontal and the vertical response spectra are established, and have been compared with each other in this study. Statistical analyses show that, for the selected 30 acceleration records, the maximum mean of vertical acceleration spectra is slightly higher than which of horizontal acceleration spectra. That means the near-fault earthquake really have significant vertical effect. Consulting the domestic and international research achievement, the normalized near-fault design spectrum adapted to Chinese seismic design Code (GB50011-2010) is established in horizontal direction. The results show that, within short period range, the horizontal near-fault design spectrum obtained in this paper is obviously higher than which derived from Chinese seismic code. Subsequently, the spectra of horizontal components for the selected 30 records are each scaled to match the horizontal near-fault design spectrum at two periodic points of 1.0 and 1.5 sec respectively, and the corresponding vertical spectra are scaled with the horizontal spectra at the same time. The scaled results reveal that the vertical spectra have much higher discretion than horizontal spectra, hence the study in this paper could initiates the research interest to a new aspect concerned with the randomness of vertical spectra for near-fault ground motions, which would affect the seismic reliability of structures significantly.

Power Analysis of Sdof Structures with Tuned Inerter Dampers Subjected to Earthquake Ground Motions

2020 ◽  
Author(s):  
Wenai Shen ◽  
Zhentao Long ◽  
Heng Wang ◽  
Hongping Zhu
Keyword(s):  
Seismic Response ◽  
Output Power ◽  
Analytical Solutions ◽  
Ground Motions ◽  
Soft Soil ◽  
Response Control ◽  
Seismic Response Control ◽  
Earthquake Ground Motions ◽  
Short Period ◽  
Soil Site

Abstract Tuned inerter dampers (TID) have been demonstrated as efficient energy dissipation devices for seismic response control. However, its potential capability for energy harvesting remains largely unexplored. Here, we present a theoretical analysis of the power of a structure-TID system subjected to earthquake ground motions. The analytical solutions of the average damping power of the system are derived for considering white noise base excitations and the Kanai-Tajimi earthquake model, respectively. Comparisons of the numerical results of a Monte Carlo simulation and the theoretical predictions verify the accuracy of the analytical solutions. Besides, we uncover the influence of the TID parameters on the damping power and output power of the system. The optimal frequency ratio of the TID for maximizing its output power slightly differs from that for seismic response control, and the former varies with site conditions. In contrast, both the damping power and output power are not sensitive to the damping ratio of the TID. For short-period structures, a small inertance-to-mass ratio (µ) of the TID is beneficial to maximize its output power, while seismic response control requires a large µ. For long-period structures, the damping power and output power are not sensitive to the µ. Generally, a structure-TID system on a soft soil site absorbs more energy from a given earthquake and is capable of harvesting more energy than that on a hard soil site. This study may help develop new strategies for self-powered control and monitoring in civil structures.

Strong motion accelerograph records from the 1993 Napierville earthquake

1995 ◽  
Vol 22 (1) ◽  
pp. 190-196
Author(s):  
René Tinawi ◽  
André Filiatrault ◽  
Pierre Léger
Keyword(s):  
Ground Motion ◽  
Energy Content ◽  
Strong Motion ◽  
Response Spectra ◽  
High Energy ◽  
Period Range ◽  
Attenuation Relationships ◽  
Acceleration Time Histories ◽  
Short Period ◽  
Time Histories

An earthquake of magnitude ML = 4.3 occurred near Napierville, Quebec, on November 16, 1993. An accelerograph at the liquefaction, storage, and regasification plant of Gaz Metropolitain in Montreal, about 55 km from the epicentre, recorded the ground motion. Although the maximum accelerations and velocities from this event are small, the acceleration time histories do confirm the high energy content in the very short period range. The recorded ground motion and corresponding absolute acceleration response spectra are presented and various attenuation relationships, proposed for eastern North America, are utilized to compare the measured and predicted ground motion parameters. Key words: Napierville earthquake, attenuation relationships, acceleration spectra, strong motion records.

Earthquake time histories compatible with the 2005 National building code of Canada uniform hazard spectrum

2009 ◽  
Vol 36 (6) ◽  
pp. 991-1000 ◽  
Author(s):  
Gail M. Atkinson
Keyword(s):  
Ground Motions ◽  
Time History ◽  
Building Code ◽  
Site Condition ◽  
Period Range ◽  
Uniform Hazard Spectrum ◽  
Finite Fault ◽  
Time Histories ◽  
Finite Fault Method ◽  
Site Classes

The seismic design provisions of the 2005 National building code of Canada (NBCC) (NRC 2005) describe earthquake ground motions for which structures are to be designed in terms of a uniform hazard spectrum (UHS) having a 2% chance of being exceeded in 50 years. The “target” UHS depends on location and site condition, where site condition is described by a classification scheme based on the time-averaged shear-wave velocity in the top 30 m of the deposit. For some applications, such as dynamic analysis by time history methods, it is useful to have time histories that represent the types of earthquake motions expected and match the target UHS from the NBCC over some prescribed period range. In this study, the stochastic finite-fault method is used to generate earthquake time histories that may be used to match the 2005 NBCC UHS for a range of Canadian sites. Records are provided for site classes A, C, D, and E. They are freely available at www.seismotoolbox.ca .

On the Seismic Response of the Faculty of Architecture and Engineering Building at Tohoku University

2016 ◽  
Vol 32 (1) ◽  
pp. 523-545 ◽  
Author(s):  
Ying Wang ◽  
Enrique Villalobos ◽  
Santiago Pujol ◽  
Hamood Al-Washali ◽  
Kazuki Suzuki ◽  
...  
Keyword(s):  
Seismic Response ◽  
Ground Motion ◽  
Structural Damage ◽  
Ground Motions ◽  
Strong Ground Motions ◽  
First Motion ◽  
Strong Ground

The Faculty of Architecture and Engineering Building at Tohoku University survived two strong ground motions. This is not surprising because the structure was stiff and strong. What is surprising is that the first ground motion did not cause severe structural damage but the second one caused so much structural damage that the building had to be evacuated and demolished. The damage occurred despite two key facts: (1) the intensities of the mentioned ground motions are understood to have been similar and (2) the building was strengthened after the first motion (and before the second) following stringent standards.

scholarly journals Engineering applications of new probabilistic seismic ground-motion maps of Canada

1983 ◽  
Vol 10 (4) ◽  
pp. 670-680 ◽  
Author(s):  
A. C. Heidebrecht ◽  
P. W. Basham ◽  
J. H. Rainer ◽  
M. J. Berry
Keyword(s):  
Ground Motion ◽  
Seismic Risk ◽  
Velocity Ratio ◽  
Large Population ◽  
Building Code ◽  
Base Shear ◽  
Probability Of Exceedance ◽  
Seismic Ground Motion ◽  
Short Period ◽  
Current Code

New peak horizontal acceleration and velocity zoning maps with a probability of exceedance of 10% in 50 years and seven seismic zones are developed from new probabilistic strong seismic ground-motion estimates for replacement of the 1970 seismic zoning map in the National Building Code of Canada. The adoption of a probability of exceedance of 10% in 50 years produces reference seismic ground motion appropriate to the level of protection afforded by provisions of the current code; the use of two ground-motion parameters, the relative levels of which vary considerably throughout the country, provides independent reference levels for structures having short and long fundamental periods.For calculating seismic base shear, a new seismic response factor is derived in which seismic forces for long-period structures are directly proportional to zonal velocities, and for short-period structures proportional to zonal accelerations, with an upper limit on the acceleration/velocity ratio applicable for any location. To maintain the same design standard as provided by the current code, the base shear is calibrated to remain the same, on average, in large population centres in regions of moderate to high seismic risk. The resulting changes in the base shear applicable at various locations reflect the improved estimates of seismic risk, in particular the introduction of additional zones in the higher risk regions of the country and the higher levels of short-period ground motion estimated for some regions of eastern Canada.These and associated changes in seismic design provisions have been recommended for adoption in the 1985 edition of the National Building Code of Canada.

Seismic loading provision changes in National Building Code of Canada 1985

1985 ◽  
Vol 12 (3) ◽  
pp. 653-660 ◽  
Author(s):  
A. C. Heidebrecht ◽  
W. K. Tso
Keyword(s):  
Seismic Response ◽  
Seismic Risk ◽  
Seismic Loading ◽  
Building Code ◽  
Seismic Zoning ◽  
Probability Level ◽  
Base Shear ◽  
Response Parameter ◽  
Most Significant Change ◽  
Risk Methodology

This paper describes the process by which Canadian seismic loading provisions are developed and then details the primary changes being introduced in the 1985 edition of the National Building Code of Canada. The most significant change is the inclusion of new seismic zoning maps, based on a new seismic risk methodology, a new probability level, and additional seismic zones, and incorporating both horizontal ground velocity and acceleration as zoning parameters. The format of base shear calculation is revised to incorporate these changes, including the specification of a new seismic response parameter. The base shear formula is calibrated to ensure that, on a cumulative basis throughout the country, the level of seismic loading remains unchanged. Additional changes discussed in the paper include the removal of dynamic analysis as a specific option in the base shear calculation and some significant changes in the calculation of torsional effects.

Sign in / Sign up

Export Citation Format

Share Document