Application de la méthode de Bishop simplifiée aux remblais renforcés par les géosynthétiques

1993 ◽  
Vol 30 (5) ◽  
pp. 812-820 ◽  
Author(s):  
Abdelkader Houam ◽  
Jean Nuyens
Keyword(s):  
Tensile Strength ◽  
Stability Analysis ◽  
Key Words ◽  
Safety Factor ◽  
Slip Surface ◽  
New Approach ◽  
Analysis And Design ◽  
Reinforced Slopes ◽  
Bishop’S Method ◽  
Slope Safety

A new approach to stability analysis and design of geosynthetic reinforced slopes based on Bishop's method is presented. The effect of sheet inclination across the slip surface on the safety factor or on tensile strength of the sheet is materialized by the introduction, in the computation, of a factor varying from 0 to 1. The reason for this move is to take the flexibility of the sheet into account. Two tables of procedure were made up in case of analysis and design. Some examples are presented by way of illustrations. Key words : slope, safety, slip surface, slice, geosynthetics.

Limit equilibrium slope stability analysis using the nonlinear strength failure criterion

2015 ◽  
Vol 52 (5) ◽  
pp. 563-576 ◽  
Author(s):  
Dong-ping Deng ◽  
Lian-heng Zhao ◽  
Liang Li
Keyword(s):  
Stability Analysis ◽  
Slope Stability ◽  
Safety Factor ◽  
Failure Criterion ◽  
Slip Surface ◽  
Limit Equilibrium ◽  
Current Method ◽  
Slope Stability Analysis ◽  
Strength Failure ◽  
Slope Safety

The limit equilibrium stability analysis of two- and three-dimensional slopes with the nonlinear failure strength criterion uses a number of variables to determine the normal and shear stress on the slip surface. The equation for the nonlinear strength failure criterion is expressed using a Taylor series after analyzing the stress of an elemental slice or column. Multivariate linear equations are then derived to determine these variables based on the force and moment equilibrium conditions the sliding body is subject to. The stress on the slip surface can also be obtained to calculate the slope safety factor. The validity of the current method was verified by comparing it with established examples. Charts were produced for slope stability analysis with the nonlinear strength failure criterion under general conditions using the current method. The results of this study show that the slope safety factor decreases with an increase in the geotechnical material parameter m in the nonlinear strength failure criterion. The results of the current method are in close correspondence with other traditional limit equilibrium methods and are more reliable than the Swedish method. The charts can be used to determine slope design parameters that meet specific requirements.

Slope Stability Analysis of Elastic Limit Equilibrium Method

2013 ◽  
Vol 275-277 ◽  
pp. 1423-1426
Author(s):  
Lin Kuang ◽  
Ai Zhong Lv ◽  
Yu Zhou
Keyword(s):  
Stability Analysis ◽  
Slope Stability ◽  
Safety Factor ◽  
Slip Surface ◽  
Limit Equilibrium ◽  
Limit Equilibrium Method ◽  
Slope Stability Analysis ◽  
Sliding Surface ◽  
Tangential Stresses ◽  
Equilibrium Method

Based on finite element analysis software ANSYS, slope stability analysis is carried out by Elastic limiting equilibrium method proposed in this paper. A series of sliding surface of the slope can be assumed firstly, and then stress field along the sliding surface is analyzed as the slope is in elastic state. The normal and tangential stresses along each sliding surface can be obtained, respectively. Then the safety factor for each slip surface can be calculated, the slip surface which the safety factor is smallest is the most dangerous sliding surface. This method is different from the previous limit equilibrium method. For the previous limit equilibrium method, the normal and tangential stresses along the sliding surface are calculated based on many assumptions. While, the limit equilibrium method proposed in this paper has fewer assumptions and clear physical meaning.

scholarly journals Application of Harmony Search Algorithm to Slope Stability Analysis

Land ◽  
2021 ◽  
Vol 10 (11) ◽  
pp. 1250
Author(s):  
Sina Shaffiee Haghshenas ◽  
Sami Shaffiee Haghshenas ◽  
Zong Woo Geem ◽  
Tae-Hyung Kim ◽  
Reza Mikaeil ◽  
...  
Keyword(s):  
Stability Analysis ◽  
Slope Stability ◽  
Safety Factor ◽  
Search Algorithm ◽  
Limit Equilibrium ◽  
Harmony Search ◽  
Harmony Search Algorithm ◽  
Slope Stability Analysis ◽  
Unit Weight ◽  
Slope Safety

Slope stability analysis is undoubtedly one of the most complex problems in geotechnical engineering and its study plays a paramount role in mitigating the risk associated with the occurrence of a landslide. This problem is commonly tackled by using limit equilibrium methods or advanced numerical techniques to assess the slope safety factor or, sometimes, even the displacement field of the slope. In this study, as an alternative approach, an attempt to assess the stability condition of homogeneous slopes was made using a machine learning (ML) technique. Specifically, a meta-heuristic algorithm (Harmony Search (HS) algorithm) and K-means algorithm were employed to perform a clustering analysis by considering two different classes, depending on whether a slope was unstable or stable. To achieve the purpose of this study, a database made up of 19 case studies with 6 model inputs including unit weight, intercept cohesion, angle of shearing resistance, slope angle, slope height and pore pressure ratio and one output (i.e., the slope safety factor) was established. Referring to this database, 17 out of 19 slopes were categorized correctly. Moreover, the obtained results showed that, referring to the considered database, the intercept cohesion was the most significant parameter in defining the class of each slope, whereas the unit weight had the smallest influence. Finally, the obtained results showed that the Harmony Search algorithm is an efficient approach for training K-means algorithms.

Movement and stability analysis of the Beaver Creek landslide, Saskatchewan, Canada

1985 ◽  
Vol 22 (3) ◽  
pp. 277-285 ◽  
Author(s):  
R. T. Yoshida ◽  
J. Krahn
Keyword(s):  
Stability Analysis ◽  
Key Words ◽  
Residual Strength ◽  
Case History ◽  
Single Unit ◽  
Slip Surface ◽  
Friction Angle ◽  
Slide Mass ◽  
History Of ◽  
Residual Values

This paper presents a case history of a multiblock landslide where the blocks move at varying rates along a common horizontal slip surface which follows the contact between stratified drift and underlying till. Movement measurements indicate that the blocks towards the toe move at a higher rate than blocks towards the scarp. Stability analyses show that the entire slide mass can be analyzed as a single unit as opposed to considering each block separately. This finding is compared with the analysis of other multiblock slides. The friction angle mobilized along the horizontal slip surface falls within the range of residual values measured in the laboratory. Key words: landslides, stability, analysis, translational slides, residual strength.

scholarly journals Stability Analysis of Anchored Soil Slope Based on Finite Element Limit Equilibrium Method

2016 ◽  
Vol 2016 ◽  
pp. 1-8
Author(s):  
Rui Zhang ◽  
Jie Zhao ◽  
Guixuan Wang
Keyword(s):  
Finite Element ◽  
Stability Analysis ◽  
Safety Factor ◽  
Slip Surface ◽  
Limit Equilibrium ◽  
Limit Equilibrium Method ◽  
Element Analysis ◽  
Surface Anchoring ◽  
Equilibrium Method ◽  
Slice Method

Under the condition of the plane strain, finite element limit equilibrium method is used to study some key problems of stability analysis for anchored slope. The definition of safe factor in slices method is generalized into FEM. The “true” stress field in the whole structure can be obtained by elastic-plastic finite element analysis. Then, the optimal search for the most dangerous sliding surface with Hooke-Jeeves optimized searching method is introduced. Three cases of stability analysis of natural slope, anchored slope with seepage, and excavation anchored slope are conducted. The differences in safety factor quantity, shape and location of slip surface, anchoring effect among slices method, finite element strength reduction method (SRM), and finite element limit equilibrium method are comparatively analyzed. The results show that the safety factor given by the FEM is greater and the unfavorable slip surface is deeper than that by the slice method. The finite element limit equilibrium method has high calculation accuracy, and to some extent the slice method underestimates the effect of anchor, and the effect of anchor is overrated in the SRM.

A Comparative Study on Locating Critical Slip Surface in 2D and 3D Limit Equilibrium Stability Analysis of Slopes

2012 ◽  
Vol 446-449 ◽  
pp. 1905-1913
Author(s):  
Mo Wen Xie ◽  
Zeng Fu Wang ◽  
Xiang Yu Liu ◽  
Ning Jia
Keyword(s):  
Stability Analysis ◽  
Slope Stability ◽  
Safety Factor ◽  
Slip Surface ◽  
Limit Equilibrium ◽  
Three Dimensional ◽  
Slope Stability Analysis ◽  
Equilibrium Stability ◽  
Critical Slip Surface ◽  
Minimum Safety Factor

The Various methods of optimization or random search have been developed for locating the critical slip surface of a slope and the related minimum safety factor in the limit equilibrium stability analysis of slope. But all these methods are based on a two-dimensional (2D) method and no one had been adapted for a search of the three-dimensional (3D) critical slip surface. In this paper, a new Monte Carlo random simulating method has been proposed to identify the 3D critical slip surface, in which assuming the initial slip to be the lower part of an ellipsoid, the 3D critical slip surface in the 3D slope stability analysis is located by minimizing the 3D safety factor of limit equilibrium approach. Based on the column-based three-dimensional limit equilibrium slope stability analysis models, new Geographic Information Systems (GIS) grid-based 3D deterministic limit equilibrium models are developed to calculate the 3D safety factors. Several practical examples, of obtained minimum safety factor and its critical slip surface by a 2D optimization or random technique, are extended to 3D slope problems to locate the 3D critical slip surface and to compare with the 2D results. The results shows that, comparing with the 2D results, the resulting 3D critical slip surface has no apparent difference only from a cross section, but the associated 3D safety factor is definitely higher.

scholarly journals ANALISIS PENGARUH TEKANAN AIR PORI PADA LERENG YANG DIPERKUAT DENGAN GEOTEKSTIL

2021 ◽  
Vol 4 (1) ◽  
pp. 139
Author(s):  
Satria Seprianto ◽  
Andryan Suhendra
Keyword(s):  
Tensile Strength ◽  
Pore Water ◽  
Safety Factor ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Slope Reinforcement ◽  
Slope Safety

ABSTRACTInfrastructure development in Indonesia is growing  rapidly. With the large number of infrastructure developments in various slope topographies, it is one of the locations that is part of this development. The slope area is prone to landslides so that strengthening is necessary. One of the reinforcement that can be done is with geotextiles. In its installation, it is necessary to calculate the correct length and strength of the geotextile for reinforcement. The tensile strength and length of the geotextile as well as the parameters of the embankment affect the safety factor of slope construction. One of the factors being considered is the pore water pressure which reduces the slope strength. So that the results of this study will show how much the influence of pore water pressure on slope reinforcement with geotextiles. After analysis, it was found that the increase of pore water pressure resulted in decreasing of slope safety factor.ABSTRAKPembangunan infarstruktur di Indonesia berkembang sangat pesat. Dengan banyaknya pembangunan imfrastruktur di berbagai topografi lereng menjadi salah satu lokasi yang menjadi bagian dalam pembangunan tersebut. Daerah lereng rawan akan terjadinya longsor sehingga perlu dilakukan perkuatan. Salah perkuatan yang dapat dilakukan adalah dengan geotekstil. Dalam pemasangannya dibutuhkan perhitungan panjang dan kuat geotekstil yang tepat untuk perkuatan. Kuat tarik dan panjang geotekstil serta parameter tanah timbunan mempengaruhi faktor keamanan konstruksi lereng. Salah satu faktor yang dipertimbangkan adalah tekanan air pori yang menjadi penurunan kekuatan lereng. Sehingga hasil studi ini akan menunjukkan seberapa besar pengaruh tekanan air pori pada perkuatan lereng dengang geotekstil. Setelah dilakukannya analisis didapatkan bahwa kenaikan tekanan air pori mengakibatkan penurunan nilai faktor keamanan lereng.

Landslides stabilization - optimise solutions or maximize costs - case study

2018 ◽  
Vol 3 (2) ◽  
pp. 1-8
Author(s):  
Tomasz Bardel
Keyword(s):  
Stability Analysis ◽  
Additional Data ◽  
Slip Surface ◽  
Analysis And Design ◽  
The Road ◽  
Slope Reinforcement ◽  
On The Road ◽  
Analysis Of Stability ◽  
Stability Modeling

The stabilization of landslide is usually very costly, which is why optimal slope reinforcement should be based on exact geological investigations. The described case of a small landslide on the road in the Carpathians presents the process of documenting, stability analysis and design solutions for slope reinforcement. Depth of slip surface was the most important information for slope reinforcement first-design. Collapsed slope was subjected to re-analysis of stability, taking into account additional data already obtained during slope reinforcement. Stability modeling results indicate a different range and depth of the slip surface than those use for design, which had a major impact on the costs of stabilization.

scholarly journals Determining the Critical Slip Surface of Three-Dimensional Soil Slopes from the Stress Fields Solved Using the Finite Element Method

2016 ◽  
Vol 2016 ◽  
pp. 1-11 ◽  
Author(s):  
Yu-chuan Yang ◽  
Hui-ge Xing ◽  
Xing-guo Yang ◽  
Jia-wen Zhou
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Stability Analysis ◽  
Safety Factor ◽  
Slip Surface ◽  
Three Dimensional ◽  
Soil Slope ◽  
Critical Slip Surface ◽  
The Finite Element Method ◽  
The Stability

The slope stability problem is an important issue for the safety of human beings and structures. The stability analysis of the three-dimensional (3D) slope is essential to prevent landslides, but the most important and difficult problem is how to determine the 3D critical slip surface with the minimum factor of safety in earth slopes. Basing on the slope stress field with the finite element method, a stability analysis method is proposed to determine the critical slip surface and the corresponding safety factor of 3D soil slopes. Spherical and ellipsoidal slip surfaces are considered through the analysis. The moment equilibrium is used to compute the safety factor combined with the Mohr-Coulomb criteria and the limit equilibrium principle. Some assumptions are introduced to reduce the search range of center points and the radius of spheres or ellipsoids. The proposed method is validated by a classical 3D benchmark soil slope. Simulated results indicate that the safety factor of the benchmark slope is 2.14 using the spherical slip surface and 2.19 using the ellipsoidal slip surface, which is close to the results of previous methods. The simulated results indicate that the proposed method can be used for the stability analysis of a 3D soil slope.

scholarly journals Application of cuckoo search method in 3D slope stability analysis for limestone quarry mine

2020 ◽  
Vol 23 (2) ◽  
pp. 57-65
Author(s):  
Masagus Azizi ◽  
◽  
Irfan Marwanza ◽  
Nadya Hartanti ◽  
Muhammad Ghifari ◽  
...  
Keyword(s):  
Stability Analysis ◽  
Slope Stability ◽  
Safety Factor ◽  
Slip Surface ◽  
Limit Equilibrium ◽  
Cuckoo Search ◽  
Slope Stability Analysis ◽  
Efficient Global Optimization ◽  
Grid Search ◽  
3D Slope Stability

The Cuckoo Search (CS) is a very fast and efficient global optimization method to locating the slip surface which carried out by iteration. However, the Grid Search (conventional method) method in 3D slope stability analysis takes longer than this method on the computation process. Slope stability analysis was performed using the 3D limit equilibrium method “Bishop” with Cuckoo Search of slip surface by maximizing iteration of the simulation and columns in X or Y. To ensure that the slip surface within the global minimum slip surface, the maximum iteration in CS was also specified from 40 to 1200. Based on maximum columns in X or Y, the safety factor value of the 3D CS results was then compared to the Grid Search results to determine the final 3D safety factor and the estimated volume of potential failure. The final 3D safety factor obtained from the average 3D safety factor (with maximum iteration 400, 800, 1000, and 1200) is about 2,01 with the average estimated volume of slope failure of 190.000 m3 that located at the north of the pit.

Sign in / Sign up

Export Citation Format

Share Document