Perovskite Oxide Thin Film Heterostructures for IR Detector

1998 ◽  
Vol 12 (29n31) ◽  
pp. 3381-3384
Author(s):  
N. J. Wu ◽  
A. Ignatiev ◽  
Y. S. Chen
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Infrared Detectors ◽  
Pulsed Laser ◽  
Ferroelectric Thin Films ◽  
Laser Deposition ◽  
Perovskite Oxide ◽  
Oxide Thin Film ◽  
Deposition Technique ◽  
Ir Detector

Mn and Sb-doped PbZrTiO 3 (PMSZT) ferroelectric thin films were integrated to high-T c superconducting YB2Cu3O 7-x (YBCO) thin films on LaAlO 3 (100) and YSZ/Si (100) substrates by the pulsed laser deposition technique. The PZT/YBCO and PM-SZT/YBCO infrared detectors were fabricated and examined as to their photovoltage and photocurrent in response to IR source temperature, and IR wavelength. The detector has relatively high IR sensitivity with a detectivity of ~ 108 cm · Hz 1/2/ W in the wavelength range of 3–16 μm.

Preparation and Characterization of MFM and MFIS Structures Using Sr2(Ta1划x, Nbx)2O7 Thin Film by Pulsed Laser Deposition

2000 ◽  
Vol 655 ◽  
Author(s):  
Masanori Okuyama ◽  
Toshiyuki Nakaiso ◽  
Minoru Noda
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Ferroelectric Thin Films ◽  
Laser Deposition ◽  
Polarization Reversal ◽  
Ambient Gas ◽  
Mfis Structure

AbstractSr2(Ta1划x, Nbx)2O7(STN) ferroelectric thin films have been prepared on SiO2/Si(100) substrates by the pulsed laser deposition (PLD) method. Preferential (110) and (151)-oriented STN thin films are deposited at a low temperature of 600°C in N2O ambient gas at 0.08 Torr. A counterclockwise C-V hysteresis was observed in the metal-ferroelectric-insulator-semiconductor (MFIS) structure using Sr2(Ta0.7, Nb0.3)2O7 on SiO2/Si deposited at 600°C. Memory window in the C-V curve spreads symmetrically towards both positive and negative directions when applied voltage increases and the window does not change in sweep rates ranging from 0.1 to 4.0×103 V/s. The C-V curve of the MFIS structure does not degrade after 1010 cycles of polarization reversal. The gate retention time is about 3.0×103 sec when the voltages and time of write pulse are ±15V and 1.0 sec, respectively, and hold bias was -0.5 V.

CRYSTALLINE SrTiO3 THIN FILMS ON SILICON BY PULSED LASER DEPOSITION

2005 ◽  
Vol 19 (01n03) ◽  
pp. 533-535
Author(s):  
J. H. HAO ◽  
J. GAO
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Perovskite Oxide ◽  
Deposition Technique ◽  
X Ray Diffraction ◽  
Rocking Curve ◽  
X Ray ◽  
Silicon Materials

We have developed a process to grow SrTiO 3 ( STO ) thin films showing single (110) orientation directly on Si by means of pulsed laser deposition technique. The growth of STO films directly on Si has been described. The crystallinity of the grown STO films was characterized by X-ray diffraction analysis of θ-2θ scan and rocking curve. Our results may be of interest for better understanding of the growth based on the perovskite oxide thin films on silicon materials.

Electrochromic WO3-x and Colossal Magnetoresistive (La, Sr)MnO3 Perovskite Oxide Thin Films by Pulsed Laser Deposition

2002 ◽  
Vol 728 ◽  
Author(s):  
Fumiaki Mitsugi ◽  
Eiichi Hiraiwa ◽  
Tomoaki Ikegami ◽  
Kenji Ebihara ◽  
Yoshiaki Suda
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Laser Energy ◽  
Pulsed Laser ◽  
High Sensitivity ◽  
Laser Deposition ◽  
Perovskite Oxide ◽  
Oxide Thin Films ◽  
Colossal Magnetoresistive

AbstractThe functional oxide thin films of electrochromic WO3-x and colossal magnetoresistive La0.8Sr0.2MnO3 were prepared by a KrF excimer pulsed laser deposition technique. Optical transparency and electrical conductivity of the WO3-x film were changed by the oxygen content in the lattice. Triclinic, tetragonal and amorphous WO3-x films were prepared by adjusting the oxygen atmosphere during the deposition. We revealed the relationship between the crystal structure and the gas sensing property of the films. The triclinic WO3-x film (1 μm) showed the high sensitivity to NO (60 ppm) gas at an operating temperature of 150°C. The colossal magnetoresistive La0.8Sr0.2MnO3 thin film having the MR ratio of 15 % (H=7 kG) was deposited under the conditions of the laser energy density of 2 J/cm2 (5Hz), substrate temperature of 850°C and oxygen pressure of 500 mTorr. The magnetic sensor composing of the La0.8Sr0.2MnO3 thin film responded to the AC magnetic field (1 kHz).

Ferroelectric Bi4Ti3O12–SrBi4Ti4O15 Intergrowth Thin Films Prepared by Pulsed Laser Deposition

2002 ◽  
Vol 748 ◽  
Author(s):  
Akira Shibuya ◽  
Minoru Noda ◽  
Masanori Okuyama
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Ferroelectric Thin Films ◽  
Laser Deposition ◽  
X Ray Diffraction ◽  
Si Substrate ◽  
X Ray ◽  
Unit Cells

ABSTRACTC axis-oriented Bi4Ti3O12–SrBi4Ti4O15 (B IT-SB Ti) intergrowth epitaxial ferroelectric thin films have been grown by pulsed laser deposition (PLD) method on MgO (001) and SrTiO3 (001) substrates. The epitaxial growth of BIT-SBTi intergrowth thin films were confirmed by X-ray diffraction (XRD) θ-2θ scan, pole figure plots and reciprocal space mappings. The c axis lattice constant of the BIT-SBTi intergrowth thin film is very close to that of made up of regular stacking of one-halves of the unit cells of Bi4Ti3O12 (3.296 nm) and SrBi4Ti4O15 (4.189 nm). The annealed BIT-SBTi thin film on Pt/Ti/SiO2/Si substrate shows intergrowth structure, too, and exhibits superior ferroelectricity that the values of 2Pr and 2Ec are 32.0 μC/cm2 and 190 kV/cm, respectively. The annealed BIT-SBTi film shows that the degradation of switching charge after 1×1010 switching cycles was 16.5%. This ferroelectric enhancement is attributed to strain of pseudo-perovskite layers interacting through Bi2O2 layer. The dielectric constant and dielectric loss of the annealed BIT-SBTi film were 433 and 0.037, respectively.

SrBi2Nb2O9 ferroelectric thin films deposited by pulsed laser deposition on textured and epitaxied platinum electrodes

2001 ◽  
Vol 11 (PR11) ◽  
pp. Pr11-133-Pr11-137
Author(s):  
J. R. Duclère ◽  
M. Guilloux-Viry ◽  
A. Perrin ◽  
A. Dauscher ◽  
S. Weber ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Ferroelectric Thin Films ◽  
Laser Deposition ◽  
Platinum Electrodes

scholarly journals Deposition pressure-induced microstructure control and plasmonic property tuning in hybrid ZnO-AgxAu1-x thin films

2021 ◽  
Author(s):  
Robynne Lynne PALDI ◽  
Xing Sun ◽  
Xin Li Phuah ◽  
Juanjuan Lu ◽  
Xinghang Zhang ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Deposition Method ◽  
Hybrid Films ◽  
Deposition Pressure ◽  
Plasmonic Metamaterials ◽  
Film Form

Self-assembled oxide-metallic alloyed nanopillars as hybrid plasmonic metamaterials (e.g., ZnO-AgxAu1-x) in a thin film form are grown using a pulsed laser deposition method. The hybrid films were demonstrated to be...

XPS analysis and luminescence properties of thin films deposited by the pulsed laser deposition technique

2010 ◽  
Vol 197 (1-3) ◽  
pp. 129-134 ◽  
Author(s):  
J. J. Dolo ◽  
H. C. Swart ◽  
E. Coetsee ◽  
J. J. Terblans ◽  
O. M. Ntwaeaborwa ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Luminescence Properties ◽  
Xps Analysis ◽  
Deposition Technique

The Dielectric Properties of Pb0.65Ba0.35ZrO3 Thin Films

2006 ◽  
Vol 306-308 ◽  
pp. 1313-1318
Author(s):  
J.S. Kim ◽  
B.H. Park ◽  
T.J. Choi ◽  
Se Hyun Shin ◽  
Jae Chul Lee ◽  
...  
Keyword(s):  
Thin Film ◽  
Thin Films ◽  
Dielectric Properties ◽  
Dielectric Loss ◽  
Deposition Temperature ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Axis Orientation ◽  
Capacitance Voltage ◽  
Bst Thin Film

Pb0.65Ba0.35ZrO3 (PBZ) thin films have been grown on MgO (001) substrates by pulsed-laser deposition (PLD). We have compared the structural and dielectric properties of PBZ films grown at various temperatures. A highly c-axis orientation has appeared at PBZ film grown at the deposition temperature of 550oC. The c-axis oriented PBZ film has also shown the largest tunability among all the PBZ films in capacitance-voltage measurements. The tunability and dielectric loss of the PBZ film was 20% and 0.00959, respectively. In addition, we have compared the temperature coefficient of capacitance (TCC) of a PBZ film with that of a Ba0.5Sr0.5TiO3 (BST) film which is a well-known material applicable to tunable microwave devices. We have confirmed that TCC value of a PBZ thin film was three-times smaller than that of a BST thin film.

Ferroelectric Properties and Microstructures of Bi4-xDyxTi3O12 Thin Films

2014 ◽  
Vol 633 ◽  
pp. 378-381
Author(s):  
Bei Li ◽  
X.B. Liu ◽  
M. Chen ◽  
X.A. Mei
Keyword(s):  
Thin Films ◽  
Electrical Properties ◽  
Layered Structure ◽  
Remanent Polarization ◽  
Single Phase ◽  
Ferroelectric Properties ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Deposition Technique ◽  
Si Substrates

Dy-doped Bi4Ti3O12 thin films were fabricated on Pt/Ti/SiO2/Si substrates by pulsed laser deposition technique, and the structures and electrical properties of the films were investigated. XRD results indicated that all of Bi4-xDyxTi3O12 films consisted of single phase of a bismuth-layered structure with well-developed rod-like grains. The remanent polarization ( Pr ) and coercive field (Ec) of the Bi4-xDyxTi3O12 Film with x=0.75 were 25μC/cm2 and 85KV/cm , respectively.

Luminescent Characteristics of Pulsed Laser Deposited Epitaxial Eu-Doped Y2O3 Films

1999 ◽  
Vol 574 ◽  
Author(s):  
D. Kumar ◽  
K. G. Cho ◽  
Zhang Chen ◽  
V. Craciun ◽  
P. H. Holloway ◽  
...  
Keyword(s):  
Thin Films ◽  
Pulsed Laser Deposition ◽  
Epitaxial Growth ◽  
Yttrium Oxide ◽  
Lattice Mismatch ◽  
Pulsed Laser ◽  
Laser Deposition ◽  
Deposition Technique ◽  
Deposition Parameters

AbstractThe growth, structural and cathodoluminescent (CL) properties of europium activated yttrium oxide (Eu:Y2O3) thin films are reported. The Eu:Y2O3 films were grown in-situ using a pulsed laser deposition technique. Our results show that Eu:Y2O3 films can grow epitaxially on (100) LaAlO3 substrates under optimized deposition parameters. The epitaxial growth of Eu:Y2O3 films on LaAlO3, which has a lattice mismatch of ∼ 60 %, is explained by matching of the atom positions in the lattices of the film and the substrate after a rotation. CL data from these films are consistent with highly crystalline Eu:Y2O3 films with an intense CL emission at 611 nm.

Sign in / Sign up

Export Citation Format

Share Document