Magnetic CoFe2O4/carbon nanotubes composites: fabrication, microstructure and magnetic response

2014 ◽  
Vol 28 (12) ◽  
pp. 1450095 ◽  
Author(s):  
Panfeng Wang ◽  
Jingcai Xu ◽  
Yanbing Han ◽  
Bo Hong ◽  
Hongxiao Jin ◽  
...  
Keyword(s):  
Carbon Nanotubes ◽  
Magnetic Properties ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
Targeting Therapy ◽  
X Ray ◽  
Transmission Electron ◽  
Tumor Hyperthermia ◽  
Temperature Time ◽  
Microstructure And Magnetic Properties

By combining the unique microstructure of carbon nanotubes (CNTs) with the good magnetism of CoFe 2 O 4 ferrites, CoFe 2 O 4/CNTs nanocomposites were prepared by the solvothermal method for the application of targeting therapy and tumor hyperthermia. X-ray diffraction (XRD), thermal gravity analysis (TGA), transmission electron microscope (TEM) and vibrating sample magnetometer (VSM) were introduced to study the influence of the solvothermal temperature, time and the CNTs content on the microstructure and magnetic properties of CoFe 2 O 4/CNTs nanocomposites. The diameter of CoFe 2 O 4 nanoparticles coating on the surface of CNTs and the saturation magnetization (Ms) increased with the solvothermal temperature. CoFe 2 O 4/CNTs nanocomposites prepared at 180°C, 200°C and 220°C exhibited superparamagnetism at room temperature, while the samples prepared at 240°C and 260°C presented ferromagnetism. And the solvothermal time and CNTs content slightly affected the microstructure and magnetic properties, Ms and coercivity (Hc) increased slightly with the increasing solvothermal time and the decreasing CNTs content.

MICROSTRUCTURE AND MAGNETIC PROPERTIES CHANGE OF Fe3O4 NANOPARTICLES SYNTHESIZED UNDER MAGNETIC FIELDS AT ROOM TEMPERATURE

2009 ◽  
Vol 23 (23) ◽  
pp. 2723-2731 ◽  
Author(s):  
JUN WANG ◽  
SIHUA XIA ◽  
SHIHE CAO
Keyword(s):  
Magnetic Properties ◽  
Magnetic Fields ◽  
Room Temperature ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Promising Technique ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation ◽  
Microstructure And Magnetic Properties

Magnetite nanoparticles have been synthesized by a co-precipitation method under magnetic fields (0~1 T) at room temperature. The as-prepared samples were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM), vibrating sample magnetometer (VSM) and their microstructure analysis were evaluated on a Mössbauer spectrum. It was found that the Fe 3 O 4 samples produced under a magnetic field of 1 T had a much higher saturation magnetization (15.3 emu/g) than those produced under 0.6 T (7.56 emu/g) and 0 T magnetic fields (6.59 emu/g). This interesting result implies that magnetic fields can affect the growth of Fe 3 O 4 nanoparticles and further change the microstructure and crystallinity of Fe 3 O 4 nanoparticles. It is expected that this process could also be a promising technique to improve the magnetic properties of other magnetic materials.

Effect of Nitridation Magnetic Properties of Nanocrystalline Fe-Co Alloy Powders

2010 ◽  
Vol 654-656 ◽  
pp. 1106-1109
Author(s):  
Ya Qiong He ◽  
Chang Hui Mao ◽  
Jian Yang
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Alloy Powder ◽  
High Energy ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
X Ray ◽  
Transmission Electron ◽  
Nitridation Temperature ◽  
Microstructure And Magnetic Properties

Nanocrystalline Fe-Co alloy powders, which were prepared by high-energy mechanical milling, were nitrided under the mixing gas of NH3/H2 in the temperature range from 380°C to 510°C. X-ray diffraction (XRD) was used to analyze the grain size and reaction during the processing. The magnetic properties of the nitrided powders were measured by Vibrating Sample Magnetometer (VSM). The results show that with the appearance of Fe4N phase after nitride treatment, and the grain-size of FeCo phase decreases with the increase of nitridation temperature between 380°C to 450°C.The saturation magnetization of nitrided alloy powder treated at 480°C is about 18% higher than that of the initial Fe-Co alloy powder, accompanied by the reduction of the coercivity. Transmission electron microscope (TEM) was used, attempting to further analyze the effect of Fe4N phase on microstructure and magnetic properties of the powder mixtures.

scholarly journals Fabrication and magnetic properties of hierarchical nickel microwires with nanothorns

2010 ◽  
Vol 8 (2) ◽  
pp. 434-439 ◽  
Author(s):  
Junhao Zhang ◽  
Ling Yang ◽  
Xiaofang Cheng ◽  
Jinmeng Zhang ◽  
Fucai Li
Keyword(s):  
Electron Microscopy ◽  
Scanning Electron Microscopy ◽  
Magnetic Properties ◽  
Room Temperature ◽  
Cooperative Effect ◽  
Magnetic Interactions ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Scanning Electron

AbstractHierarchical nickel microwires with nanothorns were fabricated through a reduction of nickelous salt with hydrazine in diethanolamine. The product was characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), and energy-dispersive X-ray spectroscopy (EDS). The growth mechanism of the nickel microwires with nanothorns is proposed, based on the evolution of the structures and morphologies, which could be ascribed to the cooperative effect of the complexant of diethanolamine and inherent magnetic interactions. Magnetic properties of the product were measured at room temperature and compared with other shaped counterparts.

Adjusting Microstructure and Magnetic Properties of Ni-Mn-In Metamagnetic Shape Memory Alloys by Addition of Gd

2012 ◽  
Vol 535-537 ◽  
pp. 959-963
Author(s):  
Li Na Bai ◽  
Gui Xing Zheng ◽  
Jing Xin ◽  
Jian Jun Zhang
Keyword(s):  
Magnetic Field ◽  
Differential Scanning Calorimetry ◽  
Magnetic Properties ◽  
Shape Memory ◽  
Room Temperature ◽  
Vibrating Sample Magnetometry ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Microstructure And Magnetic Properties

The influences of Gd concentration on martensitic transformation and magnetic properties of NiMnIn alloys were investigated by differential scanning calorimetry (DSC) , vibrating sample magnetometry (VSM), X-ray diffraction (XRD) and etc. It shows that addition of Gd enhances martensite transition temperature and that X-ray diffraction analysis of experimental alloys is revealed which the mixture is martensite and austenite at room temperature. These alloys show promise as a metamagnetic shape memory alloy with magnetic-field-induced shape memory effect.

scholarly journals Preparation and Magnetic Properties of ZnFe2O4Nanotubes

2011 ◽  
Vol 2011 ◽  
pp. 1-5 ◽  
Author(s):  
Yan Xu ◽  
Yantian Liang ◽  
Lijuan Jiang ◽  
Huarui Wu ◽  
Hongzhi Zhao ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Room Temperature ◽  
Sol Gel ◽  
Anodic Aluminum Oxide Template ◽  
Blocking Temperature ◽  
Outer Diameter ◽  
X Ray Diffraction ◽  
X Ray ◽  
Anodic Aluminum ◽  
Transmission Electron

Ordered ZnFe2O4nanotube arrays with the average outer diameter of 100 nm were prepared in porous anodic aluminum oxide template using an improved sol-gel approach. The morphology was studied by transmission electron and field emission scanning electron microscope. X-ray diffraction result shows that the nanotubes were polycrystalline in structure. The magnetic properties of the prepared ZnFe2O4nanotubes were also studied. The results show that the sample shows typical superparamagnetism at room temperature and obvious ferromagnetism below blocking temperature.

Preparation, Characterization and Magnetic Property of MFe2O4 (m=Mn, Zn, Ni, Co) Nanoparticles

2013 ◽  
Vol 842 ◽  
pp. 35-38 ◽  
Author(s):  
Li Xia Yang ◽  
Sha Li ◽  
Jing Zhang ◽  
Zhou Chen ◽  
Shi Cheng Xu
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Magnetic Properties ◽  
Room Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Basic Source ◽  
Co Nanoparticles ◽  
Zn Nanoparticles

MFe2O4 (M=Mn, Co, Ni, Zn) Nanoparticles with diameters from 5nm to 30nm have been prepared through a hydrothermal method. In this system, ethanolamine was used as a basic source instead of NaOH. The as-prepared ferrites were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). In addition, the magnetic properties of the obtained ferrites have been studied at room temperature, showing that the magentic properties of ferrites closely depended on the chemical composition of M2+.

scholarly journals Size Effect on the Structural and Magnetic Properties of Nanosized PerovskiteLaFeO3Prepared by Different Methods

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Nguyen Thi Thuy ◽  
Dang Le Minh
Keyword(s):  
Magnetic Properties ◽  
Electron Microscope ◽  
Room Temperature ◽  
High Energy ◽  
Ferromagnetic Behavior ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation

Nanosized LaFeO3material was prepared by 3 methods: high energy milling, citrate gel, and coprecipitation. The X-ray diffraction (XRD), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) show that the orthorhombic LaFeO3phase was well formed at a low sintering temperature of 500°C in the citrate-gel and co-precipitation methods. Scanning electron microscope (SEM) and transmission electron microscope (TEM) observations indicate that the particle size of the LaFeO3powder varies from 10 nm to 50 nm depending on the preparation method. The magnetic properties through magnetization versus temperatureM(T)and magnetization verses magnetic fieldM(H)characteristics show that the nano-LaFeO3exhibits a weak ferromagnetic behavior in the room temperature, and theM(H)curves are well fitted by Langevin functions.

Preparation of FeCoZrBCu Thin Films and their Effect of Microstructure on Magnetic Properties

2007 ◽  
Vol 546-549 ◽  
pp. 2163-2166
Author(s):  
Jia Ping Cui ◽  
Li Zhong ◽  
Xiao Fang Bi
Keyword(s):  
Magnetic Properties ◽  
Room Temperature ◽  
Amorphous State ◽  
X Ray Diffraction ◽  
Dc Magnetron Sputtering ◽  
X Ray ◽  
Cu Films ◽  
Si Substrates ◽  
Transmission Electron ◽  
Deposited Films

In this work, (Fe,Co)–Zr–B–Cu films have been deposited on glass and Si substrates by DC magnetron sputtering method. X-ray diffraction analysis was used to identify the structure of the films. A transmission electron microscope (TEM) was employed to observe the microstructure for the films. Magnetic properties at room temperature were investigated by a Vibrating Sample Magnetometer (VSM). It was obtained that the as-deposited films on glass and Si substrates were in an amorphous state. In addition, it has been found that the coercivity is dependent on film thicknesses.

scholarly journals Synthesis and Magnetic Properties of Hematite Particles in a “Nanomedusa” Morphology

2014 ◽  
Vol 2014 ◽  
pp. 1-9 ◽  
Author(s):  
Jin Bae Lee ◽  
Hae Jin Kim ◽  
Janez Lužnik ◽  
Andreja Jelen ◽  
Damir Pajić ◽  
...  
Keyword(s):  
Magnetic Properties ◽  
Room Temperature ◽  
Magnetic Phase ◽  
Hydrothermal Process ◽  
Ferromagnetic State ◽  
X Ray Diffraction ◽  
Morin Transition ◽  
Preferential Direction ◽  
X Ray ◽  
Transmission Electron

We present the synthesis, characterization, and magnetic properties of hematite particles in a peculiar “nanomedusa” morphology. The particles were prepared from an iron-silica complex by a hydrothermal process in a solution consisting of ethyl acetate and ethanol. The particles’ morphology, structure, and chemical composition were investigated by transmission electron microscopy, powder X-ray diffraction, and scanning electron microscope equipped with an energy-dispersive X-ray spectrometer. The “hairy” particles consist of a spherical-like core of about 100 nm diameter and fibrous exterior composed of thin “legs” of 5 nm diameter grown along one preferential direction. The particles’ cores are crystalline and undergo a magnetic phase transition to a weakly ferromagnetic state at a temperature of 930 K that matches reasonably the Néel temperature of bulk hematite. However, unlike bulk hematite that undergoes Morin transition to an antiferromagnetic state around room temperature and small hematite nanoparticles that are superparamagnetic, the “nanomedusa” particles remain weakly ferromagnetic down to the lowest investigated temperature of 2 K. Each particle thus represents a nanodimensional “hairy” ferromagnet in a very broad temperature interval, extending much above the room temperature. Such high-temperature ferromagnetic nanoparticles are not frequently found among the nanomaterials.

Photoluminescence Enhancement of CdS Nanocrystals Fabricated on Dithiocarbamate Functionalized PET Substrates

2012 ◽  
Vol 512-515 ◽  
pp. 1511-1515
Author(s):  
Chun Lin Zhao ◽  
Li Xing ◽  
Xiao Hong Liang ◽  
Jun Hui Xiang ◽  
Fu Shi Zhang ◽  
...  
Keyword(s):  
Room Temperature ◽  
Hexagonal Structure ◽  
Diffraction Measurement ◽  
X Ray Diffraction ◽  
Visible Absorption ◽  
X Ray ◽  
Cds Nanocrystals ◽  
Morphological Studies ◽  
Transmission Electron

Cadmium sulfide (CdS) nanocrystals (NCs) were self-assembled and in-situ immobilized on the dithiocarbamate (DTCs)-functionalized polyethylene glycol terephthalate (PET) substrates between the organic (carbon disulfide diffused in n-hexane) –aqueous (ethylenediamine and Cd2+ dissolved in water) interface at room temperature. Powder X-ray diffraction measurement revealed the hexagonal structure of CdS nanocrystals. Morphological studies performed by scanning electron microscopy (SEM) and high-resolution transmission electron microscope (HRTEM) showed the island-like structure of CdS nanocrystals on PET substrates, as well as energy-dispersive X-ray spectroscopy (EDS) confirmed the stoichiometries of CdS nanocrystals. The optical properties of DTCs modified CdS nanocrystals were thoroughly investigated by ultraviolet-visible absorption spectroscopy (UV-vis) and fluorescence spectroscopy. The as-prepared DTCs present intrinsic hydrophobicity and strong affinity for CdS nanocrystals.

Sign in / Sign up

Export Citation Format

Share Document