EXPERIMENTAL INVESTIGATION OF EFFECT OF CRYO-TREATMENT ON MICROMILLING OF INCONEL 718

2020 ◽  
Vol 27 (11) ◽  
pp. 2050001
Author(s):  
PADMAJA TRIPATHY ◽  
KALIPADA MAITY
Keyword(s):  
Tool Wear ◽  
Material Removal Rate ◽  
Inconel 718 ◽  
Material Removal ◽  
High Speed ◽  
Removal Rate ◽  
Cryogenic Treatment ◽  
High Speed Steel ◽  
End Mill ◽  
Micro End Mill

In this paper, the effect of cutting parameters during micromilling on surface finish and material removal rate is presented. Inconel 718 alloy and high-speed steel micro end mill are used as work material and cutting tool, respectively. High-speed steel end mill of 1 mm diameter is subjected to cryogenic treatment. Machining studies are performed on Inconel alloy using untreated and cryogenic treated cutters. The milling tests are conducted at three different values of feed rate, cutting speed and depth of cut. Also, tool wear, microstructure and microhardness of different treated and untreated end mill are investigated and discussed in detail. The results showed that cryogenic treatment significantly improved the tool wear. The surface finish produced on machining the work-piece is better with the cryogenic treated tools than when compared with the untreated tools. The material removal rate is better with the cryogenic treated tools than when compared with the untreated tools. Improvement in tool life was up to 53.16% for Inconel 718 material when machined with cryogenically treated micro end mill.

scholarly journals Optimization of Input Parameters with Carbide Inserts and HSS Tool on CNC Turning of EN19 Steel

2019 ◽  
Vol 8 (12) ◽  
pp. 3869-3875
Keyword(s):  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Cutting Tool ◽  
Removal Rate ◽  
High Speed Steel ◽  
Machining Process ◽  
Steel Tool ◽  
Carbide Inserts

This paper deals with the experimental investigation and testing on a single point cutting tool with carbide inserts and high speed steel tool. Cutting tool has to be strong enough to withstand the wear resistance. It is to be proved that carbide inserts have better performance than HSS tools on machining operation. Components with higher surface quality, higher material removal rate in less time and lower tool wear is only possible by carbide insert tools. The tool material selected for this experiment are cemented & tungsten carbide inserts along with high speed steel tool on machining medium carbon steel EN19. The complete machining process is performed on cnc lathe machine Hence the intention of this project is to minimize the surface roughness, tool wear, machining time and increasing the material removal rate. Taguchi’s L9 orthogonal array is favor for this investigation work. The result obtained in this project can be further used for optimizing the process parameters there by optimized results helps the operator to improve the quality as well as production rate.

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

scholarly journals Towards Optimization of Surface Roughness and Productivity Aspects during High-Speed Machining of Ti–6Al–4V

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3749 ◽  
Author(s):  
Adel T. Abbas ◽  
Neeraj Sharma ◽  
Saqib Anwar ◽  
Faraz H. Hashmi ◽  
Muhammad Jamil ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Titanium Alloys ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Removal Rate ◽  
Depth Of Cut ◽  
Optimization Approach ◽  
High Speed Machining

Nowadays, titanium alloys are achieving a significant interest in the field of aerospace, biomedical, automobile industries especially due to their extremely high strength to weight ratio, corrosive resistance, and ability to withstand higher temperatures. However, titanium alloys are well known for their higher chemical reactive and low thermal conductive nature which, in turn, makes it more difficult to machine especially at high cutting speeds. Hence, optimization of high-speed machining responses of Ti–6Al–4V has been investigated in the present study using a hybrid approach of multi-objective optimization based on ratio analysis (MOORA) integrated with regression and particle swarm approach (PSO). This optimization approach is employed to offer a balance between achieving better surface quality with maintaining an acceptable material removal rate level. The position of global best suggested by the hybrid optimization approach was: Cutting speed 194 m/min, depth of cut of 0.1 mm, feed rate of 0.15 mm/rev, and cutting length of 120 mm. It should be stated that this solution strikes a balance between achieving lower surface roughness in terms of Ra and Rq, with reaching the highest possible material removal rate. Finally, an investigation of the tool wear mechanisms for three studied cases (i.e., surface roughness based, productivity-based, optimized case) is presented to discuss the effectiveness of each scenario from the tool wear perspective.

Process Research on High-Speed Small Hole Drilling by EDM Combined with Magnetic Field and Water Dispersant

2011 ◽  
Vol 189-193 ◽  
pp. 269-272 ◽  
Author(s):  
Ming Rang Cao ◽  
Xiao Di Geng
Keyword(s):  
Magnetic Field ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Removal Rate ◽  
Hole Drilling ◽  
Tool Wear Rate ◽  
The Magnetic Field

The mechanism that the magnetic field and the dispersant are helpful to chip removal, to improve the material removal rate (MRR) and to reduce the tool wear rate (TWR) was analyzed in detail.The corresponding experiments were conducted based on theoretical analysis. The experimental results show that adding a certain proportion of dispersant into the dielectric fluid and introducing the magnetic field for high speed small hole drilling by EDM can greatly improve the material removal rate and significantly decrease the tool wear rate.

Particularities of Grinding High Speed Steel Punching Tools

2011 ◽  
Vol 325 ◽  
pp. 177-182 ◽  
Author(s):  
Peter Krajnik ◽  
Radovan Drazumeric ◽  
Jeffrey Badger ◽  
Janez Kopač ◽  
Cornel Mihai Nicolescu
Keyword(s):  
Simulation Model ◽  
Material Removal Rate ◽  
Temperature Rise ◽  
Material Removal ◽  
High Speed ◽  
Removal Rate ◽  
High Speed Steel ◽  
Maximum Temperature ◽  
Specific Grinding Energy ◽  
Specific Material

A simulation model of a punch grinding process has been used to determine optimal parameters to reduce grinding cycle time and achieve a constant-temperature no-burn situation. Two basic outputs of the simulation model include arc length of contact and specific material removal rate that are both time-variant. A thermal model is included in the simulation to calculate maximum grinding temperature rise. The simulation-based optimization can help to avoid thermal damage, which includes thermal softening, residual tensile stress, and rehardening burn. The grindability of high speed steel (HSS) is presented in terms of specific grinding energy versus undeformed chip thickness and maximum temperature rise versus specific material removal rate. It is shown that for a given specific material removal rate lower temperatures are achieved when grinding fast and shallow. Higher temperatures, characteristic for slow and deep grinding, soften the material leading to a lower specific grinding energy, especially if grinding is timid. Lowest values of specific grinding energy can be achieved in fast and shallow grinding at aggressive grinding conditions.

Effect of SiC-Cu Electrode on Material Removal Rate, Tool Wear and Surface Roughness in EDM Process

2020 ◽  
Vol 38 (9A) ◽  
pp. 1406-1413
Author(s):  
Yousif Q. Laibia ◽  
Saad K. Shather
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
304 Stainless Steel ◽  
Tool Electrode ◽  
Pulse Time ◽  
Edm Process

Electrical discharge machining (EDM) is one of the most common non-traditional processes for the manufacture of high precision parts and complex shapes. The EDM process depends on the heat energy between the work material and the tool electrode. This study focused on the material removal rate (MRR), the surface roughness, and tool wear in a 304 stainless steel EDM. The composite electrode consisted of copper (Cu) and silicon carbide (SiC). The current effects imposed on the working material, as well as the pulses that change over time during the experiment. When the current used is (8, 5, 3, 2, 1.5) A, the pulse time used is (12, 25) μs and the size of the space used is (1) mm. Optimum surface roughness under a current of 1.5 A and the pulse time of 25 μs with a maximum MRR of 8 A and the pulse duration of 25 μs.

Optimization of Cutting Parameters in Milling Process Using Genetic Algorithm and ANOVA (March 2020)

2020 ◽  
Vol 38 (10A) ◽  
pp. 1489-1503
Author(s):  
Marwa Q. Ibraheem
Keyword(s):  
Genetic Algorithm ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Optimal Value ◽  
Optimization Of Cutting Parameters

In this present work use a genetic algorithm for the selection of cutting conditions in milling operation such as cutting speed, feed and depth of cut to investigate the optimal value and the effects of it on the material removal rate and tool wear. The material selected for this work was Ti-6Al-4V Alloy using H13A carbide as a cutting tool. Two objective functions have been adopted gives minimum tool wear and maximum material removal rate that is simultaneously optimized. Finally, it does conclude from the results that the optimal value of cutting speed is (1992.601m/min), depth of cut is (1.55mm) and feed is (148.203mm/rev) for the present work.

Process Design and Optimization of end Milling Parameters of Al 7075 Metal Matrix Composite

2021 ◽  
pp. 929-937
Author(s):  
D. S. Sai Ravi Kiran ◽  
Alavilli Sai Apparao ◽  
Vempala GowriSankar ◽  
Shaik Faheem ◽  
Sheik Abdul Mateen ◽  
...  
Keyword(s):  
Tool Wear ◽  
Material Removal Rate ◽  
Metal Matrix ◽  
Material Removal ◽  
Hybrid Composites ◽  
End Milling ◽  
Removal Rate ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Weight Percentage

This paper investigates the machinability characteristics of end milling operation to yield minimum tool wear with the maximum material removal rate using RSM. Twenty-seven experimental runs based on Box-Behnken Design of Response Surface Methodology (RSM) were performed by varying the parameters of spindle speed, feed and depth of cut in different weight percentage of reinforcements such as Silicon Carbide (SiC-5%, 10%,15%) and Alumina (Al2O3-5%) in alluminium 7075 metal matrix. Grey relational analysis was used to solve the multi-response optimization problem by changing the weightages for different responses as per the process requirements of quality or productivity. Optimal parameter settings obtained were verified through confirmatory experiments. Analysis of variance was performed to obtain the contribution of each parameter on the machinability characteristics. The result shows that spindle speed and weight percentage of SiC are the most significant factors which affect the machinability characteristics of hybrid composites. An appropriate selection of the input parameters such as spindle speed of 1000 rpm, feed of 0.02 mm/rev, depth of cut of 1 mm and 5% of SiC produce best tool wear outcome and a spindle speed of 1838 rpm, feed of 0.04 mm/rev, depth of cut of 1.81 mm and 6.81 % of SiC for material removal rate.

Sign in / Sign up

Export Citation Format

Share Document