scholarly journals Towards Optimization of Surface Roughness and Productivity Aspects during High-Speed Machining of Ti–6Al–4V

Materials ◽  
2019 ◽  
Vol 12 (22) ◽  
pp. 3749 ◽  
Author(s):  
Adel T. Abbas ◽  
Neeraj Sharma ◽  
Saqib Anwar ◽  
Faraz H. Hashmi ◽  
Muhammad Jamil ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Titanium Alloys ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Removal Rate ◽  
Depth Of Cut ◽  
Optimization Approach ◽  
High Speed Machining

Nowadays, titanium alloys are achieving a significant interest in the field of aerospace, biomedical, automobile industries especially due to their extremely high strength to weight ratio, corrosive resistance, and ability to withstand higher temperatures. However, titanium alloys are well known for their higher chemical reactive and low thermal conductive nature which, in turn, makes it more difficult to machine especially at high cutting speeds. Hence, optimization of high-speed machining responses of Ti–6Al–4V has been investigated in the present study using a hybrid approach of multi-objective optimization based on ratio analysis (MOORA) integrated with regression and particle swarm approach (PSO). This optimization approach is employed to offer a balance between achieving better surface quality with maintaining an acceptable material removal rate level. The position of global best suggested by the hybrid optimization approach was: Cutting speed 194 m/min, depth of cut of 0.1 mm, feed rate of 0.15 mm/rev, and cutting length of 120 mm. It should be stated that this solution strikes a balance between achieving lower surface roughness in terms of Ra and Rq, with reaching the highest possible material removal rate. Finally, an investigation of the tool wear mechanisms for three studied cases (i.e., surface roughness based, productivity-based, optimized case) is presented to discuss the effectiveness of each scenario from the tool wear perspective.

Investigation of Surface Roughness and Material Removal Rate for High Speed Micro End Milling on PMMA

2015 ◽  
Vol 1115 ◽  
pp. 12-15
Author(s):  
Nur Atiqah ◽  
Mohammad Yeakub Ali ◽  
Abdul Rahman Mohamed ◽  
Md. Sazzad Hossein Chowdhury
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Feed Rate ◽  
Material Removal ◽  
High Speed ◽  
End Milling ◽  
Removal Rate ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Micro End Milling

Micro end milling is one of the most important micromachining process and widely used for producing miniaturized components with high accuracy and surface finish. This paper present the influence of three micro end milling process parameters; spindle speed, feed rate, and depth of cut on surface roughness (Ra) and material removal rate (MRR). The machining was performed using multi-process micro machine tools (DT-110 Mikrotools Inc., Singapore) with poly methyl methacrylate (PMMA) as the workpiece and tungsten carbide as its tool. To develop the mathematical model for the responses in high speed micro end milling machining, Taguchi design has been used to design the experiment by using the orthogonal array of three levels L18 (21×37). The developed models were used for multiple response optimizations by desirability function approach to obtain minimum Ra and maximum MRR. The optimized values of Ra and MRR were 128.24 nm, and 0.0463 mg/min, respectively obtained at spindle speed of 30000 rpm, feed rate of 2.65 mm/min, and depth of cut of 40 μm. The analysis of variance revealed that spindle speeds are the most influential parameters on Ra. The optimization of MRR is mostly influence by feed rate. Keywords:Micromilling,surfaceroughness,MRR,PMMA

scholarly journals Multi-Response Optimization of process Parameter in Vertical Milling Machine of EN 31 Using Taguchi Method

2021 ◽  
Vol 23 (11) ◽  
pp. 228-235
Author(s):  
Sunil Kumar ◽  
◽  
P.N . Rao ◽  
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Depth Of Cut ◽  
Tool Wear Rate ◽  
Vertical Milling Machine ◽  
En 31

The purpose of this experimental research is to compare the effectiveness of using Taguchi approaches for multi-response optimization of process parameters in Vertical Milling Machine of EN 31 Material intending to minimize surface roughness and tool wear rate while maximizing material removal rate to improve the productivity of the process with coated carbide insert. Taguchi L9 and Annova have been applied for experimental design and analysis. This experiment shows that feed and depth of cut are factors that are important for tool wear, Depth of cut is a notable factor for Material Removal Rate and feed is the most notable factor for surface roughness. Spindle speed has little effect on tool wear rate, surface roughness, and material removal rate. Mathematical models for three response parameters i.e. tool wear rate, surface roughness, and material removal rate were obtained by regression analysis

Influences of Varying Combination of Feed Rate and Depth of Cut to Tool Wear Rate and Surface Roughness: High Speed Machining Technique in Non-High Speed Milling Machine

2014 ◽  
Vol 903 ◽  
pp. 194-199
Author(s):  
Mohd Zairulnizam Zawawi ◽  
Mohd Ali Hanafiah Shaharudin ◽  
Ahmad Rosli Abdul Manaf
Keyword(s):  
Surface Roughness ◽  
Wear Rate ◽  
Tool Wear ◽  
Feed Rate ◽  
Material Removal ◽  
High Speed ◽  
Removal Rate ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Tool Wear Rate

Machining technique using high spindle speed, high feed rate and shallow depth of cut utilize in High Speed Milling (HSM) machines offer several benefits such as increase of productivity, elimination of secondary and semi-finishing process, reduce tool load and small chips produced. By adjusting some of the machining parameters, non-HSM machine having lower spindle speed and feed rate could also take advantages some of the benefits mentioned above when applying the HSM technique. This experiment investigate the effects of varying combination of depth of cut and feed rate to tool wear rate and surface roughness during end milling of Aluminum and P20 tool steel in dry condition. The criterion for tool wear before it gets rejected is based on maximum flank wear, Vb of 0.6mm. Material removal rate, spindle speed and radial depth of cut are constant in this experiment. After preliminary machining trials, the combination starts with depth of cut of 2mm and feed rate of 45mm/min until the smallest depth of cut and highest feed rate of 0.03mm and 3000mm/min respectively. The obtained result shows that for both materials, feed rate significantly influences the surface roughness value while depth of cut does not as the surface roughness value keep increasing with the increase of feed rate and decreasing depth of cut. Whereas, tool wear rate almost remain unchanged indicates that material removal rate strongly contribute the wear rate. With no significant tool wear rate, this study demonstrates that HSM technique is possible to be applied in non-HSM machine with extra benefits of eliminating semi-finishing operation, reducing tool load for finishing, machining without coolant and producing smaller chip for ease of cleaning.

Effects of Process Parameters on Surface Roughness and MRR in the hard turning of EN 36 steel

2018 ◽  
pp. 102-110
Author(s):  
Amritpal Singh ◽  
Rakesh Kumar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Hard Turning ◽  
Control Parameter ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting

In the present study, Experimental investigation of the effects of various cutting parameters on the response parameters in the hard turning of EN36 steel under the dry cutting condition is done. The input control parameters selected for the present work was the cutting speed, feed and depth of cut. The objective of the present work is to minimize the surface roughness to obtain better surface finish and maximization of material removal rate for better productivity. The design of experiments was done with the help of Taguchi L9 orthogonal array. Analysis of variance (ANOVA) was used to find out the significance of the input parameters on the response parameters. Percentage contribution for each control parameter was calculated using ANOVA with 95 % confidence value. From results, it was observed that feed is the most significant factor for surface roughness and the depth of cut is the most significant control parameter for Material removal rate.

Effect of SiC-Cu Electrode on Material Removal Rate, Tool Wear and Surface Roughness in EDM Process

2020 ◽  
Vol 38 (9A) ◽  
pp. 1406-1413
Author(s):  
Yousif Q. Laibia ◽  
Saad K. Shather
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
304 Stainless Steel ◽  
Tool Electrode ◽  
Pulse Time ◽  
Edm Process

Electrical discharge machining (EDM) is one of the most common non-traditional processes for the manufacture of high precision parts and complex shapes. The EDM process depends on the heat energy between the work material and the tool electrode. This study focused on the material removal rate (MRR), the surface roughness, and tool wear in a 304 stainless steel EDM. The composite electrode consisted of copper (Cu) and silicon carbide (SiC). The current effects imposed on the working material, as well as the pulses that change over time during the experiment. When the current used is (8, 5, 3, 2, 1.5) A, the pulse time used is (12, 25) μs and the size of the space used is (1) mm. Optimum surface roughness under a current of 1.5 A and the pulse time of 25 μs with a maximum MRR of 8 A and the pulse duration of 25 μs.

Enhancement of EDM Performance by Using Copper-Silver Composite Electrode

2020 ◽  
Vol 38 (9A) ◽  
pp. 1352-1358
Author(s):  
Saad K. Shather ◽  
Abbas A. Ibrahim ◽  
Zainab H. Mohsein ◽  
Omar H. Hassoon
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
High Speed ◽  
Composite Electrode ◽  
Removal Rate ◽  
Pure Copper ◽  
High Speed Steel ◽  
Pulse On Time ◽  
Pulse Off Time

Discharge Machining is a non-traditional machining technique and usually applied for hard metals and complex shapes that difficult to machining in the traditional cutting process. This process depends on different parameters that can affect the material removal rate and surface roughness. The electrode material is one of the important parameters in Electro –Discharge Machining (EDM). In this paper, the experimental work carried out by using a composite material electrode and the workpiece material from a high-speed steel plate. The cutting conditions: current (10 Amps, 12 Amps, 14 Amps), pulse on time (100 µs, 150 µs, 200 µs), pulse off time 25 µs, casting technique has been carried out to prepare the composite electrodes copper-sliver. The experimental results showed that Copper-Sliver (weight ratio70:30) gives better results than commonly electrode copper, Material Removal Rate (MRR) Copper-Sliver composite electrode reach to 0.225 gm/min higher than the pure Copper electrode. The lower value of the tool wear rate achieved with the composite electrode is 0.0001 gm/min. The surface roughness of the workpiece improved with a composite electrode compared with the pure electrode.

Optimization of Cutting Parameters in Milling Process Using Genetic Algorithm and ANOVA (March 2020)

2020 ◽  
Vol 38 (10A) ◽  
pp. 1489-1503
Author(s):  
Marwa Q. Ibraheem
Keyword(s):  
Genetic Algorithm ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Depth Of Cut ◽  
Optimal Value ◽  
Optimization Of Cutting Parameters

In this present work use a genetic algorithm for the selection of cutting conditions in milling operation such as cutting speed, feed and depth of cut to investigate the optimal value and the effects of it on the material removal rate and tool wear. The material selected for this work was Ti-6Al-4V Alloy using H13A carbide as a cutting tool. Two objective functions have been adopted gives minimum tool wear and maximum material removal rate that is simultaneously optimized. Finally, it does conclude from the results that the optimal value of cutting speed is (1992.601m/min), depth of cut is (1.55mm) and feed is (148.203mm/rev) for the present work.

Process Design and Optimization of end Milling Parameters of Al 7075 Metal Matrix Composite

2021 ◽  
pp. 929-937
Author(s):  
D. S. Sai Ravi Kiran ◽  
Alavilli Sai Apparao ◽  
Vempala GowriSankar ◽  
Shaik Faheem ◽  
Sheik Abdul Mateen ◽  
...  
Keyword(s):  
Tool Wear ◽  
Material Removal Rate ◽  
Metal Matrix ◽  
Material Removal ◽  
Hybrid Composites ◽  
End Milling ◽  
Removal Rate ◽  
Spindle Speed ◽  
Depth Of Cut ◽  
Weight Percentage

This paper investigates the machinability characteristics of end milling operation to yield minimum tool wear with the maximum material removal rate using RSM. Twenty-seven experimental runs based on Box-Behnken Design of Response Surface Methodology (RSM) were performed by varying the parameters of spindle speed, feed and depth of cut in different weight percentage of reinforcements such as Silicon Carbide (SiC-5%, 10%,15%) and Alumina (Al2O3-5%) in alluminium 7075 metal matrix. Grey relational analysis was used to solve the multi-response optimization problem by changing the weightages for different responses as per the process requirements of quality or productivity. Optimal parameter settings obtained were verified through confirmatory experiments. Analysis of variance was performed to obtain the contribution of each parameter on the machinability characteristics. The result shows that spindle speed and weight percentage of SiC are the most significant factors which affect the machinability characteristics of hybrid composites. An appropriate selection of the input parameters such as spindle speed of 1000 rpm, feed of 0.02 mm/rev, depth of cut of 1 mm and 5% of SiC produce best tool wear outcome and a spindle speed of 1838 rpm, feed of 0.04 mm/rev, depth of cut of 1.81 mm and 6.81 % of SiC for material removal rate.

Effects of Cutting Parameters on the Surface Roughness of Ti6Al4V Titanium Alloys in Side Milling

2011 ◽  
Vol 175 ◽  
pp. 289-293 ◽  
Author(s):  
Hao Liu ◽  
Chong Hu Wu ◽  
Rong De Chen
Keyword(s):  
Surface Roughness ◽  
Titanium Alloys ◽  
Material Removal Rate ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Parameters ◽  
Cutting Depth ◽  
Side Milling ◽  
Milling Parameters ◽  
Fine Grain

Side milling Ti6Al4V titanium alloys with fine grain carbide cutters is carried out. The influences of milling parameters on surface roughness are investigated and also discussed with average cutting thickness, material removal rate and vibration. The results reveal that the surface roughness increases with the increase of average cutting thickness and is primarily governed by the radial cutting depth.

scholarly journals Investigation an assisting electrode powder mixed electrical discharge machining of nonconductive ceramic

2021 ◽  
Author(s):  
Dragan Rodic ◽  
Marin Gostimirovic ◽  
Milenko Sekulic ◽  
Borislav Savkovic ◽  
Branko Strbac
Keyword(s):  
Surface Roughness ◽  
Tool Wear ◽  
Material Removal Rate ◽  
Electrical Discharge ◽  
Material Removal ◽  
Metal Removal ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
Positive Effects ◽  
Assisting Electrode

Abstract It is well known that electrical discharge machining can be used in the processing of nonconductive materials. In order to improve the efficiency of machining modern engineering materials, existing electrical discharge machines are constantly being researched and improved or developed. The current machining of non-conductive materials is limited due to the relatively low material removal rate and high surface roughness. A possible technological improvement of electrical discharge machining can be achieved by innovations of existing processes. In this paper, a new approach for machining zirconium oxide is presented. It combines electrical discharge machining with assisting electrode and powder-mixed dielectric. The assisting electrode is used to enable electrical discharge machining of nonconductive material, while the powder-mixed dielectric is used to increase the material removal rate, reduce surface roughness, and decrease relative tool wear. The response surface method was used to generate classical mathematical models, analyzing the output performances of surface roughness, material removal rate and relative tool wear. Verification of the obtained models was performed based on a set of new experimental data. By combining these latest techniques, positive effects on machining performances are obtained. It was found that the surface roughness was reduced by 18%, the metal removal rate was increased by about 12% and the relative tool wear was reduced by up to 6% compared to electrical discharge machining with supported electrode without powder.

Sign in / Sign up

Export Citation Format

Share Document