Aqueous-Base-Developable Benzocyclobutene-Based Dielectric Material - An Emerging Dielectric Material for Microelectronics

2019 ◽  
Vol 6 (3) ◽  
pp. 705-719
Author(s):  
Ying-Hung So ◽  
Edmund Stark ◽  
Scott Kisting ◽  
Dan Scheck ◽  
Kayla Baranek ◽  
...  
Keyword(s):  
Dielectric Material ◽  
Aqueous Base

High Quality HfO2 Film and Its Applications in Novel Poly-Si Devices

2002 ◽  
Vol 716 ◽  
Author(s):  
K.L. Ng ◽  
N. Zhan ◽  
M.C. Poon ◽  
C.W. Kok ◽  
M. Chan ◽  
...  
Keyword(s):  
Barrier Height ◽  
Nonvolatile Memory ◽  
Dielectric Material ◽  
Tunneling Current ◽  
Interface Layer ◽  
Si Substrate ◽  
Hfo2 Film ◽  
Effective Barrier Height ◽  
Effective Barrier ◽  
Nonvolatile Memory Devices

AbstractHfO2 as a dielectric material in MOS capacitor by direct sputtering of Hf in an O2 ambient onto a Si substrate was studied. The results showed that the interface layer formed between HfO2 and the Si substrate was affected by the RTA time in the 500°C annealing temperature. Since the interface layer is mainly composed of hafnium silicate, and has high interface trap density, the effective barrier height is therefore lowered with increased RTA time. The change in the effective barrier height will affect the FN tunneling current and the operation of the MOS devices when it is applied for nonvolatile memory devices.

Mathematical model to predict the characteristics of polarization in dielectric materials: The concept of piezoelectrcity and electrostriction

2019 ◽  
Author(s):  
Chem Int
Keyword(s):  
Mathematical Model ◽  
Electric Field ◽  
Lead Zirconate Titanate ◽  
Dielectric Material ◽  
Strain Curve ◽  
Dielectric Materials ◽  
Lead Zirconate ◽  
Simulation Software ◽  
Constitutive Law ◽  
Basic Material

Model was developed for the prediction of polarization characteristics in a dielectric material exhibiting piezoelectricity and electrostriction based on mathematical equations and MATLAB computer simulation software. The model was developed based on equations of polarization and piezoelectric constitutive law and the functional coefficient of Lead Zirconate Titanate (PZT) crystal material used was 2.3×10-6 m (thickness), the model further allows the input of basic material and calculation of parameters of applied voltage levels, applied stress, pressure, dielectric material properties and so on, to generate the polarization curve, strain curve and the expected deformation change in the material length charts. The mathematical model revealed that an application of 5 volts across the terminals of a 2.3×10-6 m thick dielectric material (PZT) predicted a 1.95×10-9 m change in length of the material, which indicates piezoelectric properties. Both polarization and electric field curve as well as strain and voltage curve were also generated and the result revealed a linear proportionality of the compared parameters, indicating a resultant increase in the electric field yields higher polarization of the dielectric materials atmosphere.

scholarly journals Influence of the Porosity of Polymer Foams on the Performances of Capacitive Flexible Pressure Sensors

Sensors ◽  
2019 ◽  
Vol 19 (9) ◽  
pp. 1968 ◽  
Author(s):  
Sylvie Bilent ◽  
Thi Hong Nhung Dinh ◽  
Emile Martincic ◽  
Pierre-Yves Joubert
Keyword(s):  
Experimental Data ◽  
Linear Model ◽  
Dielectric Material ◽  
Pressure Sensors ◽  
Volume Ratio ◽  
Measurement Range ◽  
Polymer Foams ◽  
First Order ◽  
Non Linear ◽  
Flexible Pressure Sensors

This paper reports on the study of microporous polydimethylsiloxane (PDMS) foams as a highly deformable dielectric material used in the composition of flexible capacitive pressure sensors dedicated to wearable use. A fabrication process allowing the porosity of the foams to be adjusted was proposed and the fabricated foams were characterized. Then, elementary capacitive pressure sensors (15 × 15 mm2 square shaped electrodes) were elaborated with fabricated foams (5 mm or 10 mm thick) and were electromechanically characterized. Since the sensor responses under load are strongly non-linear, a behavioral non-linear model (first order exponential) was proposed, adjusted to the experimental data, and used to objectively estimate the sensor performances in terms of sensitivity and measurement range. The main conclusions of this study are that the porosity of the PDMS foams can be adjusted through the sugar:PDMS volume ratio and the size of sugar crystals used to fabricate the foams. Additionally, the porosity of the foams significantly modified the sensor performances. Indeed, compared to bulk PDMS sensors of the same size, the sensitivity of porous PDMS sensors could be multiplied by a factor up to 100 (the sensitivity is 0.14 %.kPa−1 for a bulk PDMS sensor and up to 13.7 %.kPa−1 for a porous PDMS sensor of the same dimensions), while the measurement range was reduced from a factor of 2 to 3 (from 594 kPa for a bulk PDMS sensor down to between 255 and 177 kPa for a PDMS foam sensor of the same dimensions, according to the porosity). This study opens the way to the design and fabrication of wearable flexible pressure sensors with adjustable performances through the control of the porosity of the fabricated PDMS foams.

Skin–core structured fluorinated MWCNTs: a nanofiller towards a broadband dielectric material with a high dielectric constant and low dielectric loss

2018 ◽  
Vol 6 (9) ◽  
pp. 2370-2378 ◽  
Author(s):  
Yang Liu ◽  
Cheng Zhang ◽  
Benyuan Huang ◽  
Xu Wang ◽  
Yulong Li ◽  
...  
Keyword(s):  
Dielectric Constant ◽  
Dielectric Loss ◽  
High Dielectric Constant ◽  
Dielectric Material ◽  
Epoxy Composite ◽  
Low Dielectric ◽  
High Dielectric

A novel skin–core structured fluorinated MWCNT nanofiller was prepared to fabricate epoxy composite with broadband high dielectric constant and low dielectric loss.

A High Permittivity Dielectric Material Filled SISL Antenna with Cavity Backing

2021 ◽  
pp. 1-1
Author(s):  
Ningning Yan ◽  
Kaixue Ma ◽  
Haipeng Fu
Keyword(s):  
Dielectric Material ◽  
High Permittivity
Sign in / Sign up

Export Citation Format

Share Document