scholarly journals Hydrodynamic Characterization of thePolyodon spathulaRostrum Using CFD

2013 ◽  
Vol 2013 ◽  
pp. 1-8 ◽  
Author(s):  
Jeffrey B. Allen ◽  
Guillermo Riveros
Keyword(s):  
Numerical Study ◽  
Filter Feeding ◽  
Unique Shape ◽  
Lift And Drag ◽  
Naca 0012

Among the various functions of the paddlefish rostrum, it is also believed to serve as a stabilizer to counteract the downward force that would otherwise occur during the process of filter feeding. From its unique shape, it is hypothesized that the paddlefish rostrum serves to generate a substantial amount of lift that naturally occurs as the rostrum is elevated at the same time the fish opens its mouth. The present, numerical study is an attempt to quantify the amount of lift (and drag) that is generated by the rostrum of a juvenile paddlefish. Additionally, this data is compared with other hydrofoils. The results suggest that the paddlefish rostrum does indeed produce substantial lift at certain angles of attack. In fact, the results indicate that the amount of lift is comparable to that produced by a symmetric foil (NACA 0012).

scholarly journals An Experimental Analysis on the Effects of Stagger on the Aerodynamic Forces of Tandem Wings

AVIA ◽  
2021 ◽  
Vol 2 (2) ◽  
Author(s):  
Y Parlindungan ◽  
S Tobing
Keyword(s):  
Experimental Analysis ◽  
Numerical Study ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Performance ◽  
Open Loop ◽  
Aerodynamic Forces ◽  
Subsonic Wind Tunnel ◽  
Lift And Drag ◽  
Naca 0012

This study is inspired by the flapping motion of natural flyers: insects. Many insects have two pairs of wings referred as tandem wings. Literature review indicates that the effects of tandem wing are influenced by parameters such as stagger (the stream-wise distance between the aerodynamic center of the front and the rear airfoil), angle-of-attack and flow velocity. As a first stage, this study focuses on the effects of stagger (St) on the aerodynamic performance of tandem wings. A recent numerical study of stagger on tandem airfoils in turbulent flow (Re = 6000000) concluded that a larger stagger resulted in a decrease in lift force, and an increase in drag force. However, for laminar flow (Re = 2000), increasing the stagger was not found to be detrimental for aerodynamic performance. Another work also revealed that the maximum lift coefficient for a tandem configuration decreased with increasing stagger. The focus of this study is to perform an experimental analysis of tandem two-dimensional (2D) NACA 0012 airfoils. The two airfoils are set at the same angle-of-attack of 0° to 15° with 5° interval and three variations of stagger: 1c, 1.5c and 2c. The experiments are conducted using an open-loop-subsonic wind tunnel at a Reynolds number of 170000. The effects of St on the aerodynamic forces (lift and drag) are analyzed

scholarly journals Numerical Study of Wind-Tunnel Wall Effects on Lift and Drag Characteristics of NACA 0012 Airfoil

CFD letters ◽  
2020 ◽  
Vol 12 (11) ◽  
pp. 72-82
Author(s):  
Mostafa Abobaker ◽  
Sogair Addeep ◽  
Abdulhafid M. Elfaghi
Keyword(s):  
Wind Tunnel ◽  
Numerical Study ◽  
Published Data ◽  
Computational Domain ◽  
Tunnel Wall ◽  
Ansys Fluent ◽  
Slope Correction ◽  
Lift Curve ◽  
Lift And Drag ◽  
Naca 0012

Possible interference effects of the wind tunnel walls play an important role especially for measurements in closed-wall test sections. In this study, a numerical analysis of two-dimensional subsonic flow over a NACA 0012 airfoil at different computational domain heights, angles of attack from 0o to 10o, and operating Reynolds number of 6×106 is presented. The work highlights the role of computational fluid dynamics (CFD) in the investigation of wind tunnel wall effect on lift curve slope correction factor (Ka). The flow solution is obtained using Ansys Fluent software by solving the steady-state continuity and momentum governing equations combined with turbulence model k-v shear stress transport (SST-K?). The numerical results are validated by comparing with the available experimental measurements. Calculations show that the lift curve slope correction results are very close to the published data.

scholarly journals A Parametric Study of Trailing Edge Flap Implementation on Three Different Airfoils Through an Artificial Neuronal Network

Symmetry ◽  
2020 ◽  
Vol 12 (5) ◽  
pp. 828
Author(s):  
Igor Rodriguez-Eguia ◽  
Iñigo Errasti ◽  
Unai Fernandez-Gamiz ◽  
Jesús María Blanco ◽  
Ekaitz Zulueta ◽  
...  
Keyword(s):  
Aerodynamic Coefficients ◽  
Trailing Edge ◽  
High Lift ◽  
Trailing Edge Flaps ◽  
Artificial Neural Network Ann ◽  
Lift And Drag ◽  
Artificial Neuronal Network ◽  
Naca 0012 ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Trailing edge flaps (TEFs) are high-lift devices that generate changes in the lift and drag coefficients of an airfoil. A large number of 2D simulations are performed in this study, in order to measure these changes in aerodynamic coefficients and to analyze them for a given Reynolds number. Three different airfoils, namely NACA 0012, NACA 64(3)-618, and S810, are studied in relation to three combinations of the following parameters: angle of attack, flap angle (deflection), and flaplength. Results are in concordance with the aerodynamic results expected when studying a TEF on an airfoil, showing the effect exerted by the three parameters on both aerodynamic coefficients lift and drag. Depending on whether the airfoil flap is deployed on either the pressure zone or the suction zone, the lift-to-drag ratio, CL/CD, will increase or decrease, respectively. Besides, the use of a larger flap length will increase the higher values and decrease the lower values of the CL/CD ratio. In addition, an artificial neural network (ANN) based prediction model for aerodynamic forces was built through the results obtained from the research.

Numerical study of geometric morphing wings of the 1303 UCAV

2021 ◽  
pp. 1-17
Author(s):  
B. Nugroho ◽  
J. Brett ◽  
B.T. Bleckly ◽  
R.C. Chin
Keyword(s):  
Flight Control ◽  
Numerical Study ◽  
Aerodynamic Characteristics ◽  
Morphing Wing ◽  
Rolling Moment ◽  
Wide Range ◽  
Morphing Wings ◽  
Wing Geometry ◽  
Lift And Drag ◽  
Wing Morphing

ABSTRACT Unmanned Combat Aerial Vehicles (UCAVs) are believed by many to be the future of aerial strike/reconnaissance capability. This belief led to the design of the UCAV 1303 by Boeing Phantom Works and the US Airforce Lab in the late 1990s. Because UCAV 1303 is expected to take on a wide range of mission roles that are risky for human pilots, it needs to be highly adaptable. Geometric morphing can provide such adaptability and allow the UCAV 1303 to optimise its physical feature mid-flight to increase the lift-to-drag ratio, manoeuvrability, cruise distance, flight control, etc. This capability is extremely beneficial since it will enable the UCAV to reconcile conflicting mission requirements (e.g. loiter and dash within the same mission). In this study, we conduct several modifications to the wing geometry of UCAV 1303 via Computational Fluid Dynamics (CFD) to analyse its aerodynamic characteristics produced by a range of different wing geometric morphs. Here we look into two specific geometric morphing wings: linear twists on one of the wings and linear twists at both wings (wash-in and washout). A baseline CFD of the UCAV 1303 without any wing morphing is validated against published wind tunnel data, before proceeding to simulate morphing wing configurations. The results show that geometric morphing wing influences the UCAV-1303 aerodynamic characteristics significantly, improving the coefficient of lift and drag, pitching moment and rolling moment.

scholarly journals Characterization of aerodynamic performance of ducted wind turbines: A numerical study

Wind Energy ◽  
2019 ◽  
Vol 22 (12) ◽  
pp. 1655-1666 ◽  
Author(s):  
Vinit V. Dighe ◽  
Gael Oliveira ◽  
Francesco Avallone ◽  
Gerard J. W. Bussel
Keyword(s):  
Wind Turbines ◽  
Numerical Study ◽  
Aerodynamic Performance

Numerical Characterization of Hot Gas Ingestion Through Turbine Rim Seals

2016 ◽  
Author(s):  
Riccardo Da Soghe ◽  
Cosimo Bianchini ◽  
Carl M. Sangan ◽  
James A. Scobie ◽  
Gary D. Lock
Keyword(s):  
Flow Rate ◽  
Numerical Study ◽  
Axial Flow ◽  
Radial Clearance ◽  
Buffering Effect ◽  
Hot Gas ◽  
Numerical Predictions ◽  
Wide Range ◽  
Thermal Buffering

This paper deals with a numerical study aimed at the characterization of hot gas ingestion through turbine rim seals. The numerical campaign focused on an experimental facility which models ingress through the rim seal into the upstream wheel-space of an axial-turbine stage. Single-clearance arrangements were considered in the form of axial- and radial-seal gap configurations. With the radial-seal clearance configuration, CFD steady-state solutions were able to predict the system sealing effectiveness over a wide range of coolant mass flow rates reasonably well. The greater insight of flow field provided by the computations illustrates the thermal buffering effect when ingress occurs: for a given sealing flow rate, the effectiveness on the rotor was significantly higher than that on the stator due to the axial flow of hot gases from stator to rotor caused by pumping effects. The predicted effectiveness on the rotor was compared with a theoretical model for the thermal buffering effect showing good agreement. When the axial-seal clearance arrangement is considered, the agreement between CFD and experiments worsens; the variation of sealing effectiveness with coolant flow rate calculated by means of the simulations display a distinct kink. It was found that the “kink phenomenon” can be ascribed to an over-estimation of the egress spoiling effects due to turbulence modelling limitations. Despite some weaknesses in the numerical predictions, the paper shows that CFD can be used to characterize the sealing performance of axial- and radial-clearance turbine rim seals.

On the crack characterization of reinforced concrete structures: Experimental and data-driven numerical study

Structures ◽  
2021 ◽  
Vol 30 ◽  
pp. 134-145
Author(s):  
Sandeep Das ◽  
Subhrajit Dutta ◽  
Dibyendu Adak ◽  
Shubhankar Majumdar
Keyword(s):  
Reinforced Concrete ◽  
Numerical Study ◽  
Concrete Structures ◽  
Data Driven ◽  
Reinforced Concrete Structures

Numerical Characterization of Flow and Heat Transfer in Pre-Swirl Systems

2017 ◽  
Author(s):  
Riccardo Da Soghe ◽  
Cosimo Bianchini ◽  
Jacopo D’Errico
Keyword(s):  
Heat Transfer ◽  
Gas Turbines ◽  
Numerical Study ◽  
Physical Phenomenon ◽  
Computational Procedure ◽  
Operating Conditions ◽  
Simulation Techniques ◽  
Numerical Characterization ◽  
Unsteady Simulation

This paper deals with a numerical study aimed at the validation of a computational procedure for the aerothermal characterization of pre-swirl systems employed in axial gas turbines. The numerical campaign focused on an experimental facility which models the flow field inside a direct-flow pre-swirl system. Steady and unsteady simulation techniques were adopted in conjunction with both a standard two-equations RANS/URANS modelling and more advanced approaches such as the Scale-Adaptive-Simulation principle, the SBES and LES. The comparisons between CFD and experiments were done in terms of swirl number development, static and total pressure distributions, receiving holes discharge coefficient and heat transfer on the rotor disc surface. Several operating conditions were accounted for, spanning 0.78·106<Reφ<1.21·106 and 0.123<λt<0.376. Overall the steady-state CFD predictions are in good agreement with the experimental evidences even though it is not able to confidently mimic the experimental swirl and pressure behaviour in some regions. Although the use of unsteady sliding mesh and direct turbulence modelling, would in principle increase the insight in the physical phenomenon, from a design perspective the tradeoff between accuracy and computational costs is not always favourable.

Numerical Characterization of Hot-Gas Ingestion Through Turbine Rim Seals

2016 ◽  
Vol 139 (3) ◽  
Author(s):  
Riccardo Da Soghe ◽  
Cosimo Bianchini ◽  
Carl M. Sangan ◽  
James A. Scobie ◽  
Gary D. Lock
Keyword(s):  
Flow Rate ◽  
Numerical Study ◽  
Axial Flow ◽  
Radial Clearance ◽  
Buffering Effect ◽  
Hot Gas ◽  
Numerical Predictions ◽  
Wide Range ◽  
Thermal Buffering

This paper deals with a numerical study aimed at the characterization of hot-gas ingestion through turbine rim seals. The numerical campaign focused on an experimental facility which models ingress through the rim seal into the upstream wheel-space of an axial-turbine stage. Single-clearance arrangements were considered in the form of axial- and radial-seal gap configurations. With the radial-seal clearance configuration, computational fluid dynamics (CFD) steady-state solutions were able to predict the system sealing effectiveness over a wide range of coolant mass flow rates reasonably well. The greater insight of flow field provided by the computations illustrates the thermal buffering effect when ingress occurs: For a given sealing flow rate, the effectiveness on the rotor was significantly higher than that on the stator due to the axial flow of hot gases from stator to rotor caused by pumping effects. The predicted effectiveness on the rotor was compared with a theoretical model for the thermal buffering effect showing good agreement. When the axial-seal clearance arrangement is considered, the agreement between CFD and experiments worsens; the variation of sealing effectiveness with coolant flow rate calculated by means of the simulations displays a distinct kink. It was found that the “kink phenomenon” can be ascribed to an overestimation of the egress spoiling effects due to turbulence modeling limitations. Despite some weaknesses in the numerical predictions, the paper shows that CFD can be used to characterize the sealing performance of axial- and radial-clearance turbine rim seals.

The Effect of Injection and Suction on the Interfacial Mass Transport Resistance in a Proton Exchange Membrane Fuel Cell Air Channel

2014 ◽  
Author(s):  
Mustafa Koz ◽  
Satish G. Kandlikar
Keyword(s):  
Proton Exchange Membrane ◽  
Numerical Study ◽  
Gas Diffusion ◽  
Proton Exchange ◽  
Channel Cross Section ◽  
Flow Through ◽  
Air Channel ◽  
Air Channels ◽  
Exchange Membrane

Proton exchange membrane fuel cells are efficient and environmentally friendly electrochemical engines. The present work focuses on air channels that bring the oxidant air into the cell. Characterization of the oxygen concentration drop from the channel to the gas diffusion layer (GDL)-channel interface is a need in the modeling community. This concentration drop is expressed with the non-dimensional Sherwood number (Sh). At the aforementioned interface, the air can have a non-zero velocity normal to the interface: injection of air to the channel and suction of air from the channel. A water droplet in the channel can constrict the channel cross section and lead to a flow through the GDL. In this numerical study, a rectangular air channel, GDL, and a stationary droplet on the GDL-channel interface are simulated to investigate the Sh under droplet induced injection/suction conditions. The simulations are conducted with a commercially available software package, COMSOL Multiphysics.

Sign in / Sign up

Export Citation Format

Share Document