scholarly journals Effects of Niobium-Loading on Sulfur Dioxide Gas-Sensing Characteristics of Hydrothermally Prepared Tungsten Oxide Thick Film

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Viruntachar Kruefu ◽  
Anurat Wisitsoraat ◽  
Sukon Phanichphant
Keyword(s):  
Spin Coating ◽  
Gas Sensing ◽  
Operating Temperature ◽  
Sensor Response ◽  
X Ray Diffraction ◽  
Optimal Operating ◽  
Impregnation Process ◽  
X Ray ◽  
Transmission Electron ◽  
Sensing Characteristics

Nb-loaded hexagonal WO3nanorods with 0–1.0 wt% loading levels were successfully synthesized by a simple hydrothermal and impregnation process and characterized for SO2sensing. Nb-loaded WO3sensing films were produced by spin coating on alumina substrate with interdigitated gold electrodes and annealed at 450°C for 3 h in air. Structural characterization by X-ray diffraction, high-resolution transmission electron microscopy, and Brunauer-Emmett-Teller analysis showed that spherical, oval, and rod-like Nb nanoparticles with 5–15 nm mean diameter were uniformly dispersed on hexagonal WO3nanorods with 50–250 nm diameter and 100 nm–5 µm length. It was found that the optimal Nb loading level of 0.5 wt% provides substantial enhancement of SO2response but the response became deteriorated at lower and higher loading levels. The 0.50 wt% Nb-loaded WO3nanorod sensing film exhibits the best SO2sensing performances with a high sensor response of ~10 and a short response time of ~6 seconds to 500 ppm of SO2at a relatively low optimal operating temperature of 250°C. Therefore, Nb loading is an effective mean to improve the SO2gas-sensing performances of hydrothermally prepared WO3nanorods.

scholarly journals Liquid petroleum gas sensing performance enhanced by CuO modification of nanocrystalline ZnO-TiO2

2016 ◽  
Vol 34 (3) ◽  
pp. 571-581
Author(s):  
R.B. Pedhekar ◽  
F.C. Raghuwanshi ◽  
V.D. Kapse
Keyword(s):  
Thick Film ◽  
Gas Sensing ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
X Ray ◽  
Molar Ratios ◽  
Transmission Electron ◽  
Liquid Petroleum Gas ◽  
Synthesized Materials ◽  
Sensing Characteristics

AbstractNanocrystalline ZnO-TiO2 (with molar ratios 9:1, 7:3, 1:1, 3:7 and 1:9) were successfully synthesized by hydrothermal method. Synthesized materials were examined with the help of X-ray diffraction and transmission electron microscope. Liquid petroleum gas sensing characteristics of the ZnO-TiO2 films were investigated at different operating temperatures. The ZnO-TiO2 thick film (with 1:1 molar ratio) exhibited good response toward liquid petroleum gas as compared to other investigated compositions. Further, liquid petroleum gas sensing characteristics of CuO modified ZnO-TiO2 thick films were investigated. 0.2 M CuO modified ZnO-TiO2 thick film exhibited excellent liquid petroleum gas sensing characteristics such as higher response (~ 1637.49 at 185 °C) with quick response time (~30 s), low recovery time (~70 s), excellent repeatability and stability at low operating temperature.

Acetylene Sensing Characteristics of SnO2 Nanowires

2015 ◽  
Vol 1119 ◽  
pp. 132-136
Author(s):  
Bing Wang
Keyword(s):  
Electron Microscopy ◽  
Thermal Evaporation ◽  
Gas Adsorption ◽  
Gas Sensing ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Material ◽  
Transmission Electron ◽  
Mems Technology ◽  
Sensing Characteristics

SnO2 nanowires have been fabricated using thermal evaporation of the mixed powders of SnO2 and active carbon with Au catalysts. The morphology and structure of the prepared nanowires are determined on the basis of field-emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectrometer (EDS), x-ray diffraction (XRD) and transmission electron microscopy (TEM). The comb-shape interdigitating electrode made by MEMS technology is used to auxiliary investigating the gas sensing performance of the synthesized SnO2 nanowires. The SnO2 nanowires have sensing response to acetylene concentration of 1000 ppm under operated temperature of 300°C. The gas sensing mechanism is attributed to the gas adsorption and desorption processes occurring on the surface of the gas sensing material.

scholarly journals Improvement in NO2 Gas Sensing Properties of Semiconductor-Type Sensors by Loading Pt into BiVO4 Nanocomposites at Room Temperature

Materials ◽  
2021 ◽  
Vol 14 (20) ◽  
pp. 5913
Author(s):  
Wang-De Lin ◽  
Shu-Yun Lin ◽  
Murthy Chavali
Keyword(s):  
Recovery Time ◽  
Gas Sensing ◽  
Fast Response ◽  
X Ray Diffraction ◽  
X Ray ◽  
Response Recovery ◽  
Transmission Electron ◽  
Surface Morphologies ◽  
Sensing Characteristics ◽  
Semiconductor Type

In the present study, we report the first attempt to prepare a conducive environment for Pt/BiVO4 nanocomposite material reusability for the promotion of sustainable development. Here, the Pt/BiVO4 nanocomposite was prepared using a hydrothermal method with various weight percentages of platinum for use in NO2 gas sensors. The surface morphologies and structure of the Pt/BiVO4 nanocomposite were characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD). The results showed that Pt added to BiVO4 with 3 wt.% Pt/BiVO4 was best at a concentration of 100 ppm NO2, with a response at 167.7, and a response/recovery time of 12/35 s, respectively. The Pt/BiVO4 nanocomposite-based gas sensor exhibits promising nitrogen dioxide gas-sensing characteristics, such as fast response, highly selective detection, and extremely short response/recovery time. Additionally, the mechanisms of gas sensing in Pt/BiVO4 nanocomposites were explored in this paper.

A Novel Tungsten Trioxide Based Gas Sensor for Indoor Formaldehyde Detection

2021 ◽  
Vol 16 (3) ◽  
pp. 363-367
Author(s):  
Gaoqi Zhang ◽  
Fan Zhang ◽  
Kaifang Wang ◽  
Tao Tian ◽  
Shanyu Liu ◽  
...  
Keyword(s):  
Electron Microscope ◽  
Gas Sensor ◽  
Indoor Air ◽  
Gas Sensing ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sensing Material ◽  
Transmission Electron ◽  
Gas Sensing Properties ◽  
Gas Response

Accurate and real-time detection of formaldehyde (HCHO) in indoor air is urgently needed for human health. In this work, a ceramic material (WO3·H2O) with unique structure was successfully prepared using an efficient hydrothermal method. The crystallinity, morphology and microstructure of the as-prepared sensing material were analyzed by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) as well as transmission electron microscope (TEM). The characterization results suggest that the as-prepared sample is composed of square-like nanoplates with uneven surface. Formaldehyde vapor is utilized as the target gas to investigate gas sensing properties of the synthesized novel nanoplates. The testing results indicate that the as-fabricated gas sensor exhibit high gas response and excellent repeatability to HCHO gas. The response value (Ra/Rg) is 24.5 towards 70 ppm HCHO gas at 350 °C. Besides, the gas sensing mechanism was described.

A Formaldehyde Gas Sensor Based on Zinc Doped Lanthanum Ferrite

2013 ◽  
Vol 873 ◽  
pp. 304-310 ◽  
Author(s):  
Jin Zhang ◽  
Yu Min Zhang ◽  
Chang Yi Hu ◽  
Zhong Qi Zhu ◽  
Qing Ju Liu
Keyword(s):  
Gas Sensing ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Sensing Properties ◽  
Transmission Electron ◽  
Lanthanum Ferrite ◽  
Gas Sensing Properties ◽  
Recovery Times ◽  
Response And Recovery ◽  
Sensing Characteristics

The gas-sensing properties of zinc doped lanthanum ferrite (Zn-LaFeO3) compounds for formaldehyde were investigated in this paper. Zn-LaFeO3 powders were prepared using sol-gel method combined with microwave chemical synthesis. The powders were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM), respectively. The formaldehyde gas-sensing characteristics for the sample were examined. The experimental results indicate that the sensor based on the sample Zn-LaFeO3 shows excellent gas-sensing properties to formaldehyde gas. At the optimal operating temperature of 250°C, the sensitivity of the sensor based on LaFe0.7Zn0.3O3 to 100ppm formaldehyde is 38, while to other test gases, the sensitivity is all lower than 20. The response and recovery times for the sample to formaldehyde gas are 100s and 100s, respectively.

Preparation of Y-Ti Bioxides Strengthened Fe-Cr Alloy by Mechanical Milling and Hot Pressing

2013 ◽  
Vol 475-476 ◽  
pp. 1307-1310
Author(s):  
Lei Dai ◽  
Ping Feng ◽  
Cai Hua Huang ◽  
Guang Wei Zhao
Keyword(s):  
Electron Microscope ◽  
Hot Pressing ◽  
Mechanical Milling ◽  
Milling Time ◽  
Operating Temperature ◽  
Oxide Dispersion Strengthened ◽  
X Ray Diffraction ◽  
Ferritic Alloys ◽  
X Ray ◽  
Transmission Electron

Oxide-dispersion-strengthened (ODS) ferritic alloys are fascinating materials for future fusion power reactors due to these materials would allow a substantial increase of the operating temperature. Y-Ti bioxides strengthened Fe-Cr alloy was produced by mechanical milling (MM) followed by hot pressing (HP). Microstructure changes of the mixed powders during mechanical milling and subsequent hot pressing were structurally characterized by means of scanning electron microscope (SEM), transmission electron microscope (TEM) and X-ray diffraction (XRD). The observations of structure of the mixed powders after MM indicated that the powders are fractured and welded with rotation and vibration of container during mechanical milling. And the particle size decreases with increasing milling time. Nanoscale Y-Ti bioxides were formed during the HP process.

scholarly journals Highly sensitive and selective sensing of H2S gas using precipitation and impregnation-made CuO/SnO2 thick films

2021 ◽  
Author(s):  
Pimpan Leangtanom ◽  
Anurat Wisitsoraat ◽  
Kata Jaruwongrangsee ◽  
Narong Chanlek ◽  
Adisorn Tuantranont ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Fast Response ◽  
Potential Candidate ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cu Content ◽  
Transmission Electron ◽  
Highly Sensitive

Abstract In this work, CuO-loaded tetragonal SnO2 nanoparticles (CuO/SnO2 NPs) were synthesized using precipitation/impregnation methods with varying Cu contents of 0–25 wt% and characterized for H2S detection. The material phase, morphology, chemical composition and specific surface area of NPs were evaluated using X-ray diffraction, transmission electron microscopy, scanning electron microscopy, energy dispersive X-ray spectroscopy, X-ray photoelectron spectroscopy and Brunauer-Emmett-Teller analysis. From gas-sensing data, the H2S responses of SnO2 NPs were greatly enhanced by CuO loading particularly at the optimal Cu content of 20 wt%. The 20 wt%CuO/SnO2 sensor showed an excellent response of 1.36⋅105 towards 10 ppm H2S and high H2S selectivity against H2, SO2, CH4 and C2H2 at a low optimum working temperature of 200°C. In addition, the sensor provided fast response and a low detection limit of less than 0.15 ppm. The CuO-SnO2 sensor could therefore be a potential candidate for H2S detection in environmental applications.

scholarly journals Sputtered SnO2/ZnO Heterostructures for Improved NO2 Gas Sensing Properties

Chemosensors ◽  
2020 ◽  
Vol 8 (3) ◽  
pp. 67 ◽  
Author(s):  
Bharat Sharma ◽  
Ashutosh Sharma ◽  
Monika Joshi ◽  
Jae-ha Myung
Keyword(s):  
Photoelectron Spectroscopy ◽  
Gas Sensing ◽  
Operating Temperature ◽  
X Ray Diffraction ◽  
X Ray ◽  
Response Recovery ◽  
No2 Gas Sensor ◽  
Highly Sensitive ◽  
Gas Sensing Properties ◽  
Gas Response

A highly sensitive and selective NO2 gas sensor dependent on SnO2/ZnO heterostructures was fabricated using a sputtering process. The SnO2/ZnO heterostructure thin film samples were characterized by field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), Energy-dispersive X-ray spectroscopy (EDS), and X-ray photoelectron spectroscopy (XPS). Sensors fabricated with heterostructures attained higher gas response (S = 66.9) and quicker response-recovery (20 s, 45 s) characteristics at 100 °C operating temperature towards 100 ppm NO2 gas efficiently in comparison to sensors based on their mono-counterparts. The selectivity and stability of SnO2/ZnO heterostructures were studied. The more desirable sensing mechanism of SnO2/ZnO heterostructures towards NO2 was described in detail.

Gas-Sensing Properties of Pt-V2O5 Thin Films for Ethanol Detection

2015 ◽  
Vol 659 ◽  
pp. 259-263 ◽  
Author(s):  
Viruntachar Kruefu ◽  
Pusit Pookmanee ◽  
Anurat Wisitsoraat ◽  
Sukon Phanichphant
Keyword(s):  
Vanadium Pentoxide ◽  
Gas Sensing ◽  
Nitrogen Adsorption ◽  
Flame Spray ◽  
X Ray Diffraction ◽  
Adsorption Method ◽  
X Ray ◽  
Transmission Electron ◽  
One Step ◽  
Ppm Level

In the present work, vanadium pentoxide (V2O5) nanoparticles have been investigated for monitoring ethanol (C2H5OH) at ppm levels in air. A one-step flame spray pyrolysis (FSP) process has been applied for the synthesis of vanadium pentoxide (V2O5) and platinum-loaded vanadium pentoxide (Pt-V2O5) nanoparticles. The samples have been studied to characterize their morphological and microstructural properties by X-ray diffraction and transmission electron microscopy. Pt addition to V2O5 samples were verified by energy dispersive X-ray spectrometry mode. The specific surface area of the nanoparticles was measured by nitrogen adsorption method. The application of the produced nanoparticles as sensitive and selective ethanol resistive sensor has been demonstrated. The Pt-loaded V2O5 sensor has shown higher response towards ethanol at ppm-level concentrations compared to unloaded one.

scholarly journals Synthesis and Characterization of Single-Crystalline SnO2Nanowires

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Dezhou Wei ◽  
Yanbai Shen ◽  
Mingyang Li ◽  
Wengang Liu ◽  
Shuling Gao ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Gas Sensing ◽  
Operating Temperature ◽  
Ambient Pressure ◽  
Silicon Substrates ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Peak Sensitivity ◽  
The Fourier Transform

Tin oxide (SnO2) nanowires were synthesized on oxidized silicon substrates by thermal evaporation of tin grains at 900°C in Ar flow at ambient pressure. Structural characterization using X-ray diffraction and transmission electron microscopy shows that SnO2nanowires have a single crystal tetragonal structure. Scanning electron microscopy observation demonstrates that SnO2nanowires are 30–200 nm in diameter and several tens of micrometers in length. The surface vibration mode resulting from the nanosize effect at 565.1 cm−1was found from the Fourier transform infrared spectrum. The formation of SnO2nanowires follows a vapour-solid (VS) growth mechanism. The gas sensing measurements indicate that SnO2nanowire gas sensor obtains peak sensitivity at a low operating temperature of 150°C and shows reversible response to H2gas (100–1000 ppm) at an operating temperature of RT-300°C.

Sign in / Sign up

Export Citation Format

Share Document