scholarly journals A Comparison of Classical and Pulsating Jets in Crossflow at Various Strouhal Numbers

2017 ◽  
Vol 2017 ◽  
pp. 1-14 ◽  
Author(s):  
Jianlong Chang ◽  
Xudong Shao ◽  
Jiangman Li ◽  
Xiao Hu

Investigation of the classical and pulsating jet in crossflow (JICF) at a low Reynolds number (Re = 100) has been performed by the LES method based on varied velocity ratios (r=  1~4). Time-averaged particle trajectories are compared in the classical and pulsating JICF. The formation mechanism and the corresponding flow characteristics for the counter-rotating vortex pair (CRVP) have been analyzed. An unexpected “vortex tail” has been found in the JICF at higher velocity ratio due to the enhanced interactions indicated by the increased jet momentum among the CRVP, upright vortices, and shear layers. The analysis of time-averaged longitudinal vorticity including a coupling mechanism between vortices has been performed. The returning streamlines appear in the pulsating JICF, and two extra converging points emerge near the nozzle of the jet at different Strouhal numbers. The temperature profiles based on the iso-surface for the classical and pulsating JICF have been obtained computationally and analyzed in detail.

2016 ◽  
Vol 9 (1) ◽  
pp. 37-46 ◽  
Author(s):  
Jianlong Chang ◽  
Xudong Shao ◽  
Xiao Hu ◽  
Shuangbiao Zhang

The jet in crossflow at very low Reynolds number (Re=100) with and without block is performed by means of large eddy simulation for the jet-to-crossflow velocity ratios (r) ranging from 1 to 3, and the corresponding flow characteristics are compared. The results show that the time-averaged particle trajectories of the jet are slightly changed if a block is presented, and the mixed vortices are weakened. The existence of the block also can accelerate the formation of stable counter-rotating vortex pair. At lower velocity ratio (r=1), the block has little effect on the jet in crossflow with a symmetrically positive and negative kidney shaped vortices. As the velocity ratio increases, the effect of block not only can generate an asymmetry of positive and negative kidney shaped vortices, but also it can reinforce the interaction between the positive and negative vortices in the jet in crossflow. The effect of block on the temperature field is also analyzed in detail.


2001 ◽  
Vol 444 ◽  
pp. 117-149 ◽  
Author(s):  
A. RIVERO ◽  
J. A. FERRÉ ◽  
FRANCESC GIRALT

An experimental study to identify the structures present in a jet in crossflow has been carried out at a jet-to-crossflow velocity ratio U/Ucf = 3.8 and Reynolds number Re = UcfD/v = 6600. The hot-wire velocity data measured with a rake of eight X-wires at x/D = 5 and 15 and flow visualizations using planar laser-induced fluorescence (PLIF) confirm that the well-established pair of counter-rotating vortices is a feature of the mean field and that the upright, tornado-like or Fric's vortices that are shed to the leeward side of the jet are connected to the jet flow at the core. The counter-rotating vortex pair is strongly modulated by a coherent velocity field that, in fact, is as important as the mean velocity field. Three different structures – folded vortex rings, horseshoe vortices and handle-type structures – contribute to this coherent field. The new handle-like structures identified in the current study link the boundary layer vorticity with the counter-rotating vortex pair through the upright tornado-like vortices. They are responsible for the modulation and meandering of the counter-rotating vortex pair observed both in video recordings of visualizations and in the instantaneous velocity field. These results corroborate that the genesis of the dominant counter-rotating vortex pair strongly depends on the high pressure gradients that develop in the region near the jet exit, both inside and outside the nozzle.


2001 ◽  
Vol 446 ◽  
pp. 347-373 ◽  
Author(s):  
L. CORTELEZZI ◽  
A. R. KARAGOZIAN

Among the important physical phenomena associated with the jet in crossflow is the formation and evolution of vortical structures in the flow field, in particular the counter-rotating vortex pair (CVP) associated with the jet cross-section. The present computational study focuses on the mechanisms for the dynamical generation and evolution of these vortical structures. Transient numerical simulations of the flow field are performed using three-dimensional vortex elements. Vortex ring rollup, interactions, tilting, and folding are observed in the near field, consistent with the ideas described in the experimental work of Kelso, Lim & Perry (1996), for example. The time-averaged effect of these jet shear layer vortices, even over a single period of their evolution, is seen to result in initiation of the CVP. Further insight into the topology of the flow field, the formation of wake vortices, the entrainment of crossflow, and the effect of upstream boundary layer thickness is also provided in this study.


2019 ◽  
Vol 865 ◽  
pp. 928-962 ◽  
Author(s):  
Haohua Zong ◽  
Marios Kotsonis

Plasma synthetic jet actuators (PSJAs) are particularly suited for high-Reynolds-number, high-speed flow control due to their unique capability of generating supersonic pulsed jets at high frequency (${>}5$  kHz). Different from conventional synthetic jets driven by oscillating piezoelectric diaphragms, the exit-velocity variation of plasma synthetic jets (PSJs) within one period is significantly asymmetric, with ingestion being relatively weaker (less than $20~\text{m}~\text{s}^{-1}$) and longer than ejection. In this study, high-speed phase-locked particle image velocimetry is employed to investigate the interaction between PSJAs (round exit orifice, diameter 2 mm) and a turbulent boundary layer at constant Strouhal number (0.02) and increasing mean velocity ratio ($r$, defined as the ratio of the time-mean velocity over the ejection phase to the free-stream velocity). Two distinct operational regimes are identified for all the tested cases, separated by a transition velocity ratio, lying between $r=0.7$ and $r=1.0$. At large velocity and stroke ratios (first regime, representative case $r=1.6$), vortex rings are followed by a trailing jet column and tilt downstream initially. This downstream tilting is transformed into upstream tilting after the pinch-off of the trailing jet column. The moment of this transformation relative to the discharge advances with decreasing velocity ratio. Shear-layer vortices (SVs) and a hanging vortex pair (HVP) are identified in the windward and leeward sides of the jet body, respectively. The HVP is initially erect and evolves into an inclined primary counter-rotating vortex pair ($p$-CVP) which branches from the middle of the front vortex ring and extends to the near-wall region. The two legs of the $p$-CVP are bridged by SVs, and a secondary counter-rotating vortex pair ($s$-CVP) is induced underneath these two legs. At low velocity and stroke ratios (second regime, representative case $r=0.7$), the trailing jet column and $p$-CVP are absent. Vortex rings always tilt upstream, and the pitching angle increases monotonically with time. An $s$-CVP in the near-wall region is induced directly by the two longitudinal edges of the ring. Inspection of spanwise planes ($yz$-plane) reveals that boundary-layer energization is realized by the downwash effect of either vortex rings or $p$-CVP. In addition, in the streamwise symmetry plane, the increasing wall shear stress is attributed to the removal of low-energy flow by ingestion. The downwash effect of the $s$-CVP does not benefit boundary-layer energization, as the flow swept to the wall is of low energy.


2017 ◽  
Vol 140 (4) ◽  
Author(s):  
Guihui Ma ◽  
Fu Chen ◽  
Jianyang Yu ◽  
Huaping Liu

Pressure-equalizing film is a slice of air layer attached to vehicle exterior with nearly uniform inside pressure, similar to ventilated cavity in composition; it is generated through exhaust process of the inside air chamber as vehicle emerges from deep water, and can reduce the lateral force and pitching moment that vertical launched underwater vehicle suffered. In this work, the emerging process of vehicle from water with pressure-equalizing exhaust was numerically calculated to investigate the evolution and flow characteristics of the generated pressure-equalizing film along its surface. Results indicated that during the whole exhaust process, the film can be obviously classified into different sections according to the distribution of phase volume fraction or pressure. The exhaust velocity ratio and flow rate from vehicle interior chamber were also found to increase as vehicle moves. In the analysis of flow structures, vortex structures such as the horseshoe vortex, “detour-separation” vortex, and counter-rotating vortex pair (CVP) can be figured out in the region of the exhaust hole. Under the effect of re-entrant jet, water around the film tail would be entrained upstream then enter the surface film to mix with the pressure-equalizing air. It leads to the happening of the three-dimensional (3D) wall vortex in the flow field.


2019 ◽  
Vol 37 (2) ◽  
pp. 1489-1496 ◽  
Author(s):  
Vedanth Nair ◽  
Matthew Sirignano ◽  
Benjamin Emerson ◽  
Ben Halls ◽  
Naibo Jiang ◽  
...  

2005 ◽  
Vol 73 (3) ◽  
pp. 474-482 ◽  
Author(s):  
Michael W. Plesniak

This paper presents a review of research done over the past several years at Purdue on non-canonical jets-in-crossflow. It is a retrospective and an integrative compilation of results previously reported as well as some new ones. The emphasis is on jets emanating from “short” holes, with length-diameter ratios of one or less. A canonical jet-in-crossflow configuration is one in which a fully developed jet issues from a long pipe fed by a large plenum, into a semi-infinite cross flow. The configuration presented here is noncanonical in the sense that jet issues from a short hole and thus the flow is unable to “adjust” to the hole, unlike the case of a long hole in which fully developed pipe flow can be attained. This is motivated by gas turbine film cooling applications. Experimental results acquired with particle image velocimetry will primarily be presented, with some complementary information gained from RANS simulations of the flow. Many different aspects of the problem have been investigated, and in this paper the focus will be on structural features within the hole and in the developing jet and crossflow interaction. A significant result is that the in-hole vortical structures, depending on their sense of rotation, tend to augment or weaken the primary counter-rotating vortex pair. This impacts global features such as jet trajectory and spreading.


2009 ◽  
Vol 624 ◽  
pp. 33-44 ◽  
Author(s):  
SHERVIN BAGHERI ◽  
PHILIPP SCHLATTER ◽  
PETER J. SCHMID ◽  
DAN S. HENNINGSON

A linear stability analysis shows that the jet in crossflow is characterized by self-sustained global oscillations for a jet-to-crossflow velocity ratio of 3. A fully three-dimensional unstable steady-state solution and its associated global eigenmodes are computed by direct numerical simulations and iterative eigenvalue routines. The steady flow, obtained by means of selective frequency damping, consists mainly of a (steady) counter-rotating vortex pair (CVP) in the far field and horseshoe-shaped vortices close to the wall. High-frequency unstable global eigenmodes associated with shear-layer instabilities on the CVP and low-frequency modes associated with shedding vortices in the wake of the jet are identified. Furthermore, different spanwise symmetries of the global modes are discussed. This work constitutes the first simulation-based global stability analysis of a fully three-dimensional base flow.


2014 ◽  
Vol 663 ◽  
pp. 322-328 ◽  
Author(s):  
Ali Ahmed Gitan ◽  
Rozli Zulkifli ◽  
Kamaruzaman Sopian ◽  
Shahrir Abdullah

The problem of environmental pollution and depletion of fossil fuel can be reduced in automotives by using an alternative bio-fuel and improve the ignition process in engine. Both solutions need to use the fuel preheating technique. This work presents the idea of fuel preheating by using exhaust impingement on the fuel tank. Heat transfer between twin pulsating hot air jets and flat copper target was investigated as an application for preheating of automotive fuel to improve ignition process in the engine. The nozzle of 20 mm was used to produce air jet of Reynolds number, Re ≃ 5500 and a temperature of 54°C. The impinged target was imposed to still air surrounding at temperature of 24°C. Pulsating frequencies of 10-50 Hz were applied on air jets by using twin pulsating jet mechanism. The effect of pulsation frequency on heat transfer was measured using IR camera and heat flux-temperature micro foil sensor. The results obtained by both of these methods showed well agreement. Also, the results revealed significant influence of flow rate difference between steady and pulsating jet cases. In addition, the highest Nusselt number, Nu ≃ 7.2, was obtained at pulsation frequency of 20 Hz.


Sign in / Sign up

Export Citation Format

Share Document