scholarly journals Design and Numerical Study of Micropump Based on Induced Electroosmotic Flow

2018 ◽  
Vol 2018 ◽  
pp. 1-6 ◽  
Author(s):  
Kai Zhang ◽  
Lengjun Jiang ◽  
Zhihan Gao ◽  
Changxiu Zhai ◽  
Weiwei Yan ◽  
...  
Keyword(s):  
Electroosmotic Flow ◽  
Stokes Equations ◽  
Numerical Study ◽  
Cross Flow ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Driving Mode ◽  
Electric Driving ◽  
Induced Charge ◽  
The Cross

Induced charge electroosmotic flow is a new electric driving mode. Based on the Navier–Stokes equations and the Poisson–Nernst–Planck (PNP) ion transport equations, the finite volume method is adopted to calculate the equations and boundary conditions of the induced charge electroosmotic flow. In this paper, the formula of the induced zeta potential of the polarized solid surface is proposed, and a UDF program suitable for the simulation of the induced charge electroosmotic is prepared according to this theory. At the same time, on the basis of this theory, a cross micropump driven by induced charge electroosmotic flow is designed, and the voltage, electric potential, charge density, and streamline of the induced electroosmotic micropump are obtained. Studies have shown that when the cross-shaped micropump is energized, in the center of the induction electrode near the formation of a dense electric double layer, there exist four symmetrical vortices at the four corners, and they push the solution towards both outlets; it can be found that the average velocity of the solution in the cross-flow microfluidic pump is nonlinear with the applied electric field, which maybe helpful for the practical application of induced electroosmotic flow in the field of micropump.

An Investigation on the Synchronization Regime of a Single Cylinder in Cross-Flow Subject to Harmonic Oscillations

2007 ◽  
Author(s):  
Waldir Terra Pinto ◽  
Marcelo Arau´jo Vitola ◽  
Carlos Antoˆnio Levi
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Time Integration ◽  
Cross Flow ◽  
Staggered Grid ◽  
Navier Stokes ◽  
Harmonic Amplitude ◽  
Navier Stokes Equations ◽  
Single Cylinder ◽  
Synchronization Regime

This work presents a numerical study on the synchronization regime of a single cylinder subject to forced harmonic motion in the transverse direction of the flow. The study is carried out for a circular cylinder for Reynolds number around 500. The forced harmonic amplitude to diameter ratio is 0.22 and the forced frequency varies from 0.2 to 4.8 Hz. The Navier-Stokes equations are solved in a non-staggered grid using a sixth-order compact difference schemes to evaluate the spatial derivatives, a low-storage third-order Runge-Kutta scheme for time integration. The cylinder is represented using a feedback force methodology. The results are compared with experimental data obtained in a water tunnel. Results show clearly that synchronization phenomenon in the fundamental frequency as well as to its super and sub-harmonics.

scholarly journals Dynamics of Single Droplet Splashing on Liquid Film by Coupling FVM with VOF

Processes ◽  
2021 ◽  
Vol 9 (5) ◽  
pp. 841
Author(s):  
Yuzhen Jin ◽  
Huang Zhou ◽  
Linhang Zhu ◽  
Zeqing Li
Keyword(s):  
Liquid Film ◽  
Weber Number ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Single Droplet ◽  
Navier Stokes Equations ◽  
Volume Method ◽  
The Relationship

A three-dimensional numerical study of a single droplet splashing vertically on a liquid film is presented. The numerical method is based on the finite volume method (FVM) of Navier–Stokes equations coupled with the volume of fluid (VOF) method, and the adaptive local mesh refinement technology is adopted. It enables the liquid–gas interface to be tracked more accurately, and to be less computationally expensive. The relationship between the diameter of the free rim, the height of the crown with different numbers of collision Weber, and the thickness of the liquid film is explored. The results indicate that the crown height increases as the Weber number increases, and the diameter of the crown rim is inversely proportional to the collision Weber number. It can also be concluded that the dimensionless height of the crown decreases with the increase in the thickness of the dimensionless liquid film, which has little effect on the diameter of the crown rim during its growth.

scholarly journals Transient Pressure-Driven Electroosmotic Flow through Elliptic Cross-Sectional Microchannels with Various Eccentricities

Computation ◽  
2021 ◽  
Vol 9 (3) ◽  
pp. 27
Author(s):  
Nattakarn Numpanviwat ◽  
Pearanat Chuchard
Keyword(s):  
Laplace Transform ◽  
Electroosmotic Flow ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Mathieu Functions ◽  
Navier Stokes Equations ◽  
Flow Rates ◽  
Elliptic Cross ◽  
Flow Through ◽  
Relative Errors

The semi-analytical solution for transient electroosmotic flow through elliptic cylindrical microchannels is derived from the Navier-Stokes equations using the Laplace transform. The electroosmotic force expressed by the linearized Poisson-Boltzmann equation is considered the external force in the Navier-Stokes equations. The velocity field solution is obtained in the form of the Mathieu and modified Mathieu functions and it is capable of describing the flow behavior in the system when the boundary condition is either constant or varied. The fluid velocity is calculated numerically using the inverse Laplace transform in order to describe the transient behavior. Moreover, the flow rates and the relative errors on the flow rates are presented to investigate the effect of eccentricity of the elliptic cross-section. The investigation shows that, when the area of the channel cross-sections is fixed, the relative errors are less than 1% if the eccentricity is not greater than 0.5. As a result, an elliptic channel with the eccentricity not greater than 0.5 can be assumed to be circular when the solution is written in the form of trigonometric functions in order to avoid the difficulty in computing the Mathieu and modified Mathieu functions.

A numerical study of the interaction between unsteay free-stream disturbances and localized variations in surface geometry

1989 ◽  
Vol 209 ◽  
pp. 285-308 ◽  
Author(s):  
R. J. Bodonyi ◽  
W. J. C. Welch ◽  
P. W. Duck ◽  
M. Tadjfar
Keyword(s):  
Numerical Solutions ◽  
Free Stream ◽  
Stokes Equations ◽  
Numerical Study ◽  
Navier Stokes ◽  
Surface Geometry ◽  
Navier Stokes Equations ◽  
S Waves ◽  
Tollmien Schlichting

A numerical study of the generation of Tollmien-Schlichting (T–S) waves due to the interaction between a small free-stream disturbance and a small localized variation of the surface geometry has been carried out using both finite–difference and spectral methods. The nonlinear steady flow is of the viscous–inviscid interactive type while the unsteady disturbed flow is assumed to be governed by the Navier–Stokes equations linearized about this flow. Numerical solutions illustrate the growth or decay of the T–S waves generated by the interaction between the free-stream disturbance and the surface distortion, depending on the value of the scaled Strouhal number. An important result of this receptivity problem is the numerical determination of the amplitude of the T–S waves.

Numerical Study of Viscous Flows Inside Partially Filled Spinning and Coning Cylinders

1996 ◽  
Vol 118 (2) ◽  
pp. 335-340 ◽  
Author(s):  
Mohamed Selmi
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Center Of Mass ◽  
Steady Motion ◽  
Practical Interest ◽  
Nonlinear Effects ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Practical Applications ◽  
Analysis And Design

This paper is concerned with the solution of the 3-D-Navier-Stokes equations describing the steady motion of a viscous fluid inside a partially filled spinning and coning cylinder. The cylinder contains either a single fluid of volume less than that of the cylinder or a central rod and a single fluid of combined volume (volume of the rod plus volume of the fluid) equal to that of the cylinder. The cylinder rotates about its axis at the spin rate ω and rotates about an axis that passes through its center of mass at the coning rate Ω. In practical applications, as in the analysis and design of liquid-filled projectiles, the parameter ε = τ sin θ, where τ = Ω/ω and θ is the angle between spin axis and coning axis, is small. As a result, linearization of the Navier-Stokes equations with this parameter is possible. Here, the full and linearized Navier-Stokes equations are solved by a spectral collocation method to investigate the nonlinear effects on the moments caused by the motion of the fluid inside the cylinder. In this regard, it has been found that nonlinear effects are negligible for τ ≈ 0.1, which is of practical interest to the design of liquid-filled projectiles, and the solution of the linearized Navier-Stokes equations is adequate for such a case. However, as τ increases, nonlinear effects increase, and become significant as ε surpasses about 0.1. In such a case, the nonlinear problem must be solved. Complete details on how to solve such a problem is presented.

Iterative method for solving fully-coupled fluid solid systems

2010 ◽  
pp. 653-670
Author(s):  
Elisabeth Longatte
Keyword(s):  
Stokes Equations ◽  
Cross Flow ◽  
Elastic Cylinder ◽  
Navier Stokes ◽  
Arbitrary Lagrangian Eulerian ◽  
Navier Stokes Equations ◽  
Ale Formulation ◽  
Volume Method ◽  
Fully Coupled ◽  
Solid System

This work is concerned with the modelling of the interaction of a fluid with a rigid or a flexible elastic cylinder in the presence of axial or cross-flow. A partitioned procedure is involved to perform the computation of the fully-coupled fluid solid system. The fluid flow is governed by the incompressible Navier-Stokes equations and modeled by using a fractional step scheme combined with a co-located finite volume method for space discretisation. The motion of the fluid domain is accounted for by a moving mesh strategy through an Arbitrary Lagrangian-Eulerian (ALE) formulation. Solid dyncamics is modeled by a finite element method in the linear elasticity framework and a fixed point method is used for the fluid solid system computation. In the present work two examples are presented to show the method robustness and efficiency.

Experimental and Numerical Study of Vortex Induced Vibrations on a Spool Model

2018 ◽  
Author(s):  
David Gross ◽  
Yann Roux ◽  
Benjamin Rousse ◽  
François Pétrié ◽  
Ludovic Assier ◽  
...  
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Flow Perturbation ◽  
Industry Standards ◽  
Vortex Induced Vibrations ◽  
Recommended Practices ◽  
Decay Tests

The problem of Vortex-Induced Vibrations (VIV) on spool and jumper geometries is known to present several drawbacks when approached with conventional engineering tools used in the study of VIV on risers. Current recommended practices can lead to over-conservatism that the industry needs to quantify and minimize within notably cost reduction objectives. Within this purpose, the paper will present a brief critical review of the Industry standards and more particularly focus on both experimental and Computational Fluid Dynamic (CFD) approaches. Both qualitative and quantitative comparisons between basin tests and CFD results for a 2D ‘M-shape’ spool model will be detailed. The results presented here are part of a larger experimental and numerical campaign which considered a number of current velocities, heading and geometry configurations. The vibratory response of the model will be investigated for one of the current velocities and compared with the results obtained through recommended practices (e.g. Shear7 and DNV guidelines). The strategy used by the software K-FSI to solve the fluid-structure interaction (FSI) problem is a partitioned coupling solver between fluid solver (FINE™/Marine) and structural solvers (ARA). FINE™/Marine solves the Reynolds-Averaged Navier-Stokes Equations in a conservative way via the finite volume method and can work on structured or unstructured meshes with arbitrary polyhedrons, while ARA is a nonlinear finite element solver with a large displacement formulation. The experiments were conducted in the BGO FIRST facility located in La Seyne sur Mer, France. Particular attention was paid towards the model design, fabrication, instrumentation and characterization, to ensure an excellent agreement between the structural numerical model and the actual physical model. This included the use of a material with low structural damping, the performance of stiffness and decay tests in air and in still water, plus the rationalization of the instrumentation to be able to capture the response with the minimum flow perturbation or interaction due to instrumentation.

Large Eddy Simulation of Cross Flow in Pipe Junction

2018 ◽  
Author(s):  
Jiajun Chen ◽  
Yue Sun ◽  
Hang Zhang ◽  
Dakui Feng ◽  
Zhiguo Zhang
Keyword(s):  
Large Eddy Simulation ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Cross Flow ◽  
Exciting Force ◽  
Navier Stokes ◽  
Pipe Network ◽  
Eddy Simulation ◽  
Large Eddy

Mixing in pipe junctions can play an important role in exciting force and distribution of flow in pipe network. This paper investigated the cross pipe junction and proposed an improved plan, Y-shaped pipe junction. The numerical study of a three-dimensional pipe junction was performed for calculation and improved understanding of flow feature in pipe. The filtered Navier–Stokes equations were used to perform the large-eddy simulation of the unsteady incompressible flow in pipe. From the analysis of these results, it clearly appears that the vortex strength and velocity non-uniformity of centerline, can be reduced by Y-shaped junction. The Y-shaped junction not only has better flow characteristic, but also reduces head loss and exciting force. The results of the three-dimensional improvement analysis of junction can be used in the design of pipe network for industry.

Numerical Prediction of Turbulent Wakes Behind a Square Cylinder

1998 ◽  
Vol 14 (1) ◽  
pp. 23-29
Author(s):  
Robert R. Hwang ◽  
Sheng-Yuh Jaw
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Navier Stokes ◽  
Wall Region ◽  
Square Cylinder ◽  
Mean Velocity ◽  
Navier Stokes Equations ◽  
Turbulent Vortex Shedding ◽  
Model Equations ◽  
Good Agreement

ABSTRACTThis paper presents a numerical study on turbulent vortex shedding flows past a square cylinder. The 2D unsteady periodic shedding motion was resolved in the calculation and the superimposed turbulent fluctuations were simulated with a second-order Reynolds-stress closure model. The calculations were carried out by solving numerically the fully elliptic ensemble-averaged Navier-Stokes equations coupled with the turbulence model equations together with the two-layer approach in the treatment of the near-wall region. The performance of the computations was evaluated by comparing the numerical results with data from available experiments. Results indicate that the present study gives good agreement in the shedding frequency and mean drag as well as in some phase profiles of the mean velocity.

Sign in / Sign up

Export Citation Format

Share Document