scholarly journals Effect of Rock Particle Content on the Mechanical Behavior of a Soil-Rock Mixture (SRM) via Large-Scale Direct Shear Test

2019 ◽  
Vol 2019 ◽  
pp. 1-16
Author(s):  
Longqi Liu ◽  
Xuesong Mao ◽  
Yajun Xiao ◽  
Qian Wu ◽  
Ke Tang ◽  
...  
Keyword(s):  
Shear Strength ◽  
Normal Stress ◽  
Large Scale ◽  
Direct Shear Test ◽  
Shear Test ◽  
Volumetric Strain ◽  
Direct Shear ◽  
Stress Strain ◽  
Particle Content ◽  
Rock Particle

The mechanical strength of the landslide deposits directly affects the safety and operation of the roads in the western mountainous area of China. Therefore, the research is aimed at studying the mechanisms of a landslide deposit sample with different rock particle contents by analyzing its characteristics of the stress-strain behavior, the “jumping” phenomenon, the volumetric strain, and the shear strength parameters via a large-scale direct shear test. Stress-strain results show that stress-strain curves can be divided into 3 different stages: liner elastic stage, yielding stage, and strain-hardening stage. The shear strength of SRM behaves more like “soil” at a lower rock particle content and behaves more like “rock joints” at a higher rock particle content. Characteristics of the “jumping” phenomenon results show that the “intense jumping” stage becomes obvious with the increasing rock particle content and the normal stress. However, the lower the rock particle content is, the more obvious the “jumping” phenomenon under the same normal stress is. Volumetric strain results show that the sample with a lower rock particle content showed a dilatancy behavior under the low normal stress and shrinkage behavior under the high normal stress. The dilatancy value becomes smaller with the increasing normal stress. The maximum shear stress value of the rock particle content corresponds to the maximum value of dilatancy or shrinkage. We also conclude that the intercept of the Mohr failure envelope of the soil-rock mixture should be called the “equivalent cohesion,” not simply called the “cohesion.” The higher the normal stress and rock particle content are, the bigger the equivalent cohesion and the internal friction angle is.

scholarly journals Influence of Maximum Particle Diameter on the Mechanical Behavior of Soil-Rock Mixtures

2020 ◽  
Vol 2020 ◽  
pp. 1-9
Author(s):  
Zhuoling He ◽  
Junyun Zhang ◽  
Tao Sun
Keyword(s):  
Shear Strength ◽  
Large Scale ◽  
Direct Shear Test ◽  
Shear Test ◽  
Particle Diameter ◽  
Size Difference ◽  
Direct Shear ◽  
Fine Grained ◽  
Fine Grained Soil ◽  
Maximum Particle

With the steady development of the development of the western region in China, the construction of mountain highways has developed rapidly, and the soil-rock mixed filler, as an excellent filler, is widely used in the subgrade filling of mountain highways. Unlike ordinary fine-grained soil, the source of the soil-rock mixtures (S-RMs) is not unique, and the particle size difference is large and the water content is not uniform, resulting in very complicated mechanical properties. But the current highway embankment codes are still mainly established on the fine-grained soil. It is not fully applicable to soil-rock filled embankment. Based on soil-rock filled embankment engineering practice, this research uses a large-scale direct shear test to research the mechanical characteristics of the S-RMs with different maximum particle diameters. According to the large-scale direct shear test of S-RMs with different maximum particle diameters, the shear displacement vs shear stress curve, shear dilation, and strength characteristics with maximum particle diameter were analyzed. Results demonstrate that whether secondary hardening occurs mainly depends on the normal stress and the maximum particle diameter of the filler. At different maximum particle diameters, the horizontal displacement vs vertical displacement curves of the S-RMs can be roughly divided into continuous shearing and beginning of shearing and quick dilation. And the shear strength increases with the increase of the maximum particle diameter. Moreover, the cohesion decreases first and then increases with the increase of the maximum particle diameter, and the internal friction angle increases with the increase of the maximum particle diameter. Therefore, some RBs with large particle diameter added to filler can effectively improve the shear strength of the S-RMs, which may be valuable for realistic engineering.

scholarly journals Determining the Shear Strength Properties of a Soil-geogrid Interface Using a Large-scale Direct Shear Test Apparatus

2020 ◽  
Author(s):  
Jakub Stacho ◽  
Monika Sulovska ◽  
Ivan Slavik
Keyword(s):  
Shear Stress ◽  
Shear Strength ◽  
Large Scale ◽  
Direct Shear Test ◽  
Shear Test ◽  
Strength Properties ◽  
Coarse Grained ◽  
Direct Shear ◽  
Test Apparatus ◽  
Fine Gravel

The paper deals with the laboratory testing of coarse-grained soils that are reinforced using a geogrid. The shear strength properties were determined using a large-scale direct shear test apparatus. The tests were executed on original as well as on reinforced soil, when the geogrid was placed on a sliding surface, which permitted determining the shear strength properties of the soil-geogrid interface. The aim of the tests was to determine the interface shear strength coefficient α, which represents the ratio of the shear strength of the soil-geogrid interface to the unreinforced soil. The tests were executed on 3 samples of coarse-grained materials, i.e., poorly graded sand, poorly graded fine gravel and poorly graded medium gravel. Two types of geogrids were tested, i.e., a woven polyester geogrid and a stiff polypropylene geogrid. The results of the laboratory tests on the medium gravel showed that the reduction coefficient α reached higher values in the case of the stiff polypropylene geogrid. In the cases of the fine gravel and sand, the values of the interface coefficient α were similar to each other. The shear strength of the interface was reduced or was similar to the shear strength of unreinforced soil in a peak shear stress state, but significantly increased with horizontal deformations, especially for the fine gravel and sand. The largest value of the coefficient α was measured in the critical shear stress state. Based on the results of the testing, a correlation which allows for determining the optimal grain size distribution was obtained.

scholarly journals Comparative Study in Method of Compaction by Consolidated Drained and Direct Shear Test

2020 ◽  
Vol 78 (2) ◽  
pp. 143-152
Author(s):  
Abdul Samad Abdul Rahman ◽  
N. Sidek ◽  
Juhaizad Ahmad ◽  
N. Hamzah ◽  
M. I. F. Rosli
Keyword(s):  
Shear Strength ◽  
Bearing Capacity ◽  
Triaxial Test ◽  
Direct Shear Test ◽  
Shear Test ◽  
Void Ratio ◽  
Direct Shear ◽  
Test Results ◽  
Stress Strain ◽  
Strain Behaviour

Soil compaction has been a common practice in the construction of highways, embankments, earth dams and other related structures where the condition of the soil is high in void ratio and therefore having a very low in bearing capacity. Therefore, the soil needs to be compacted in order to minimize the void ratio and in the same time would results in having a very high bearing capacity to sustain load. Nevertheless, only a few researches have been done to investigate the method of compaction using different energy on the behavior of shear strength by consolidated drained and direct shear test. In this research, the effect of different compaction in energy of 25 number of blows compared to 40 number of blows on the stress-strain behaviour of drained triaxial test has been done and findings of the data are to be compared with direct shear test. Results reveal that there is an increase in soil unit weight by using different energy in compaction with an increase of 5% from 1790 kg/m3 to 1880 kg/m3 for 25 and 40 number of blows respectively. However, the stress-strain behaviour of the specimens shows differently when compared between consolidated drained triaxial and direct shear test. The shear strength for direct shear-stress is at higher value compared to drained triaxial test. For drained triaxial test, results reveal that the effective friction angles are increase only about 1% from 37° to 38°. This is due to the soil particles rearranging itself with the different applied pressures thus eliminating the effects of different energy on the shear strength of the specimens. However, for direct shear test, the shear strength increases drastically from 29° to 32°. The increase of the shear strength is more likely influence by the soil particle arrangement due to the impact of the energy of the no of blows to the desired specimen.

scholarly journals Investigating the Effect of Rock Bridge on the Stability of Locked Section Slopes by the Direct Shear Test and Acoustic Emission Technique

Sensors ◽  
2020 ◽  
Vol 20 (3) ◽  
pp. 638 ◽  
Author(s):  
Qifeng Guo ◽  
Jiliang Pan ◽  
Meifeng Cai ◽  
Ying Zhang
Keyword(s):  
Acoustic Emission ◽  
Shear Strength ◽  
Normal Stress ◽  
Direct Shear Test ◽  
Shear Test ◽  
Rock Slope ◽  
Direct Shear ◽  
Acoustic Emission Technique ◽  
Rock Bridge ◽  
The Stability

As a portion of intact rock separating joint surfaces, rock bridge plays a significant role in the stability of rock slopes. This paper aims to investigate the effect of different rock bridges on the mechanical properties and failure mode of rock slope by means of the direct shear test and acoustic emission technique. Field conditions were simulated in direct shear tests which were carried out on specimens with rock bridges at different continuity rates, normal stress, arrangements, and joint angles. Experimental results indicate that the strength of specimens is controlled by the rock bridge and the structural plane. The rock bridge contributes to the strength of the specimen, while the through plane weakens the strength of the specimen. The increase of normal stress can weaken the stress concentration near the tip of the rock bridge and improve the shear resistance of the specimen. The different arrangement of rock bridge has little effect on the normal displacement of the specimen, and has a great influence on the shear strength. The shear capacity of the specimen is related to the angle of the crack, and the angle of the crack is approximately proportional to the peak shear strength. For the specimens with different joint occurrence, the mode of crack propagation at the initial stage is basically the same, and the specimen is finally damaged due to the generation of through cracks in the core area of rock bridge. The instantaneous release of the huge energy generated during the experiment along the shear direction is the root cause of the sudden failure of the rock bridge. The formation, aggregation, and transfixion process of rock bridge is of concern and has been experimentally investigated in this paper for the prevention and control of the locked section rock slope with sudden disasters.

Evaluation the Shear Strength Behavior of aged MSW using Large Scale In Situ Direct Shear Test, a case of Tabriz Landfill

2020 ◽  
Vol 18 (7) ◽  
pp. 717-733 ◽  
Author(s):  
Mohsen Keramati ◽  
Masoud Shahedifar ◽  
Mohammad Hosein Aminfar ◽  
Hasan Alagipuor
Keyword(s):  
Shear Strength ◽  
Large Scale ◽  
Direct Shear Test ◽  
Shear Test ◽  
Direct Shear ◽  
Strength Behavior

scholarly journals Influence of water and rock particle contents on the shear behaviour of a SRM

2020 ◽  
Vol 2 (1) ◽  
pp. 29-43
Author(s):  
Longqi Liu ◽  
Xuesong Mao ◽  
Yajun Xiao ◽  
Tiequan Wang ◽  
Menglan Nie
Keyword(s):  
Shear Strength ◽  
Water Content ◽  
Normal Stress ◽  
Volumetric Strain ◽  
Friction Angle ◽  
Shear Behaviour ◽  
Mountainous Area ◽  
Particle Content ◽  
Rock Particle ◽  
Influence Of Water

Abstract The contents of both water and rock particles are important factors affecting the mechanical strength of a soil–rock mixture (SRM) filled subgrade in the western mountainous area of China. Therefore, the purpose of this paper is to study the mechanisms of reconstituted landslide deposit samples with different water and rock particle contents by analysing the characteristics of shear strength, volumetric strain and ‘jumping’ phenomenon via large-scale direct shear tests. The results show that the influence of water content on shear strength is greater than the influence of rock particle content under a lower normal stress, and the results are reversed in the case of a higher normal stress. The effect of water content on the equivalent cohesion is bigger, especially for the sample with a high rock particle content. The friction angle of the specimen with same water content increases with the increasing rock particle content, but when the number of rock particles increases to a certain extent, there is a little effect on the friction angle. However, the friction angle decreases with increasing water content at the same rock particle content. Specimens with the same rock particle content change from dilation to compression with increasing water content. Finally, the continuous stage of the ‘intense jumping’ at different water content has been analysed. The ‘jumping’ phenomenon of samples with low water and rock particle content will first strengthen and then weaken the samples with increasing normal stress.

scholarly journals Influence of Structural Plane Microscopic Parameters on Direct Shear Strength

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Yanhui Cheng ◽  
Weijun Yang ◽  
Dongliang He
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Internal Friction ◽  
Direct Shear Test ◽  
Shear Test ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Direct Shear ◽  
Stiffness Ratio ◽  
Structural Plane

Structural plane is a key factor in controlling the stability of rock mass engineering. To study the influence of structural plane microscopic parameters on direct shear strength, this paper established the direct shear mechanical model of the structural plane by using the discrete element code PFC2D. From the mesoscopic perspective, the research on the direct shear test for structural plane has been conducted. The bonding strength and friction coefficient of the structural plane are investigated, and the effect of mesoscopic parameters on the shear mechanical behavior of the structural plane has been analyzed. The results show that the internal friction angle φ of the structural plane decreases with the increase of particle contact stiffness ratio. However, the change range of cohesion is small. The internal friction angle decreases first and then increases with the increase of parallel bond stiffness ratio. The influence of particle contact modulus EC on cohesion c is relatively small. The internal friction angle obtained by the direct shear test is larger than that obtained by the triaxial compression test. Parallel bond elastic modulus has a stronger impact on friction angle φ than that on cohesion c. Under the same normal stress conditions, the shear strength of the specimens increases with particle size. The shear strength of the specimen gradually decreases with the increase of the particle size ratio.

Soil Shear Strength Characteristic in Slope Disintegration Area

2013 ◽  
Vol 353-356 ◽  
pp. 735-739
Author(s):  
Xiao Ming Zhang ◽  
Shu Wen Ding ◽  
Shuang Xi Li
Keyword(s):  
Shear Strength ◽  
Direct Shear Test ◽  
Shear Test ◽  
Clay Content ◽  
Scientific Basis ◽  
Soil Mechanic ◽  
Direct Shear ◽  
Soil Cohesion ◽  
Soil Shear Strength ◽  
The Relationship

Development of slope disintegration is close to soil mechanic characteristics such as shear strength indices. Soil grain diameter and water content were tested. Soil direct shear test was conducted to analyze the relationship between shear strength indices and the influencing factors. The experimental data indicate that clay content and the range affect soil cohesion value and the scope. Soil cohesion increases with bulk density before 1.6g/cm3. But it decreases when the bulk after that. The results could provide a scientific basis for control of slope disintegration.

Sign in / Sign up

Export Citation Format

Share Document