scholarly journals Influence of Structural Plane Microscopic Parameters on Direct Shear Strength

2018 ◽  
Vol 2018 ◽  
pp. 1-7 ◽  
Author(s):  
Yanhui Cheng ◽  
Weijun Yang ◽  
Dongliang He
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Internal Friction ◽  
Direct Shear Test ◽  
Shear Test ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Direct Shear ◽  
Stiffness Ratio ◽  
Structural Plane

Structural plane is a key factor in controlling the stability of rock mass engineering. To study the influence of structural plane microscopic parameters on direct shear strength, this paper established the direct shear mechanical model of the structural plane by using the discrete element code PFC2D. From the mesoscopic perspective, the research on the direct shear test for structural plane has been conducted. The bonding strength and friction coefficient of the structural plane are investigated, and the effect of mesoscopic parameters on the shear mechanical behavior of the structural plane has been analyzed. The results show that the internal friction angle φ of the structural plane decreases with the increase of particle contact stiffness ratio. However, the change range of cohesion is small. The internal friction angle decreases first and then increases with the increase of parallel bond stiffness ratio. The influence of particle contact modulus EC on cohesion c is relatively small. The internal friction angle obtained by the direct shear test is larger than that obtained by the triaxial compression test. Parallel bond elastic modulus has a stronger impact on friction angle φ than that on cohesion c. Under the same normal stress conditions, the shear strength of the specimens increases with particle size. The shear strength of the specimen gradually decreases with the increase of the particle size ratio.

scholarly journals Study on Water Characteristic Curve and Shear Characteristics of Typical Unsaturated Silty Clay in Shaoxing

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-15
Author(s):  
Ruiqian Wu ◽  
Youzhi Tang ◽  
Shaohe Li ◽  
Wei Wang ◽  
Ping Jiang ◽  
...  
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Unsaturated Soil ◽  
Direct Shear Test ◽  
Shear Test ◽  
Characteristic Curve ◽  
Friction Angle ◽  
Matric Suction ◽  
Silty Clay ◽  
Direct Shear

In order to probe into one simplified method to predict the shear strength of Shaoxing unsaturated silty clay, the test method combining unsaturated soil consolidation instrument and conventional direct shear instrument is used to study the shear strength, and the method is compared and verified with the results of equal suction direct shear test. The research results show that the soil water characteristic curve fitted by the measured data points and VG model has obvious stage characteristics in the range of 0~38 kPa, 38~910 kPa, and 910~10000 kPa. The shear strength of unsaturated soil measured by consolidation meter combined with conventional direct shear test is in good agreement with that measured by equal suction direct shear test in the range of 0~500 kPa. The results show that the shear strength, total cohesion, and effective internal friction angle of soil increase slightly with the increase of matric suction in the range of 0~38 kPa. When the matric suction increases from 38 kPa to 500 kPa, the shear strength and total cohesion force of the soil have similar stage characteristics with the SWCC, which first increases and then tends to be stable, while the effective internal friction angle changes slightly. Finally, taking the air-entry value as the demarcation point, an improved model of unsaturated shear strength is proposed by analyzing the error value. Compared with the measured value, the absolute value of relative error is basically kept in the range of 5%~10%, which is close to the measured value.

scholarly journals Determination of the Effect of Soil Particle Size Distribution on the Shear Behavior of Sand

2021 ◽  
Vol 5 (2) ◽  
pp. 125
Author(s):  
Mohammad Afrazi ◽  
Mahmoud Yazdani
Keyword(s):  
Particle Size ◽  
Shear Strength ◽  
Direct Shear Test ◽  
Shear Test ◽  
Friction Angle ◽  
Particle Sizes ◽  
Direct Shear ◽  
Shear Tests ◽  
Direct Shear Tests

Many geotechnical problems require the determination of soil engineering properties such as shear strength. Therefore, the determination of the reliable values for this parameter is essential. For this purpose, the direct shear test, as one of the oldest tests to examine the shear strength of soils, is the most common way in laboratories to determine the shear parameters of soil. There are far too many variables that influence the results of a direct shear test. In this paper, a series of 10 × 10 cm direct shear tests were carried out on four different poorly graded sands with different particle size distributions to determine their shear behaviors. Four different poorly graded sands with a different median diameter or medium value of particle size distribution (D50) (0.2, 0.53, 1.3, and 2.3 mm) has been selected, and about 40 direct shear tests were conducted. It was concluded that a soil’s friction angle is affected by coarse-grained material. Accordingly, sandy soils with bigger particle sizes record a higher friction angle than soils containing small particles. The investigations also showed that sand with bigger particle sizes has a higher dilation angle. In addition, a non-linear regression analysis was performed to establish the exact relationship between the friction angle of the soil and the characteristics of the soil particles. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium provided the original work is properly cited.

scholarly journals Shear strength characteristics of Jerash expansive soil

2021 ◽  
Vol 3 (2) ◽  
pp. 74-80
Author(s):  
Talal Masoud
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Water Content ◽  
Direct Shear Test ◽  
Shear Test ◽  
Expansive Soil ◽  
Content Increase ◽  
Direct Shear ◽  
Initial Water ◽  
Angle Of Internal Friction

The results of the direct shear test on Jerash expansive soil show the effect of the initial water content on the cohesion (c) and on the angel of internal friction ( ) [shear strength parameters].it show that, as the initial water increase, the cohesion (c) of Jerash expansive soil also increase up to the shrinkage limit, after that increase of water even small amount, decrease the cohesion of the soil. On the other hand, the results of direct shear test show also  that as the water content increase, the angle of internal friction ( )remain unchanged up to shrinkage limit , any increase of water cause a large decrease on the angle of internal friction of Jerash expansive soil.

Study on the Granular Shear Strength Parameters of Dumping Site

2012 ◽  
Vol 256-259 ◽  
pp. 358-361
Author(s):  
Xiang Yun Kong ◽  
Guang Jin Wang ◽  
Xiao Chao Zhou
Keyword(s):  
Particle Size ◽  
Grain Size ◽  
Shear Strength ◽  
Internal Friction ◽  
Friction Angle ◽  
Internal Friction Angle ◽  
Shear Strength Parameters ◽  
Strength Parameters ◽  
Dumping Site ◽  
Size Grading

Apparent particle size grading is the important characteristic of super-high bench dumping site, and the critical factors with the impact of its stability and disaster prevention are the fragmentation distribution and shear strength parameters of granular. With the copper mine dumping site which had the feature of apparent particle size grading, the thesis carried out the study of on-site particle size investigation and indoor laboratory. The particle-size distribution law with the changing of dumping-site height was analyzed and quantitative relationship between the fragmentation distribution and shear strength parameters of granular was discussed. The research results indicated that coarse-grain contents and maximum grain size were increased significantly according to the decreasing of dumping-site height, which showed that the dumping-site had the feature of apparent particle size grading. The coarse particle content in the grain size composition and internal friction angle φ of shear strength parameters increased with the obvious increment of the distribution value B. The relationship between distribution value B and the internal friction angle φ could be expressed by exponential function curve.

scholarly journals Study on Shear Properties of the Soil-rock Mixture

2020 ◽  
Vol 165 ◽  
pp. 04079
Author(s):  
B Li
Keyword(s):  
Particle Size ◽  
Moisture Content ◽  
Large Scale ◽  
Direct Shear Test ◽  
Shear Test ◽  
Friction Angle ◽  
Direct Shear ◽  
Shear Properties ◽  
Maximum Particle Size ◽  
Maximum Particle

In order to study the shear properties of the soil-rock mixture, a large-scale indoor direct shear test is used to test the shear strength (τ) of SRM under different positive pressures, and calculates the internal friction angle (φ) and cohesive force (c) according to the molar theory. The effects of soil-rock ratio, gradation, maximum particle size, moisture content, and compaction on the shear properties of the soil-rock mixtures are studied. The results show that as the soil-rock ratio decreases, the τ and φ of the SRM increase, while the c increases first and then decreases, and reaches the maximum peak when the soil-rack ratio is 40:60. As the maximum particle size increases, the τ and φ of the SRM increase, while the c decreases. With the increase of the moisture content, the τ, φ and c of the SRM all increase first and then decrease, and reach the maximum peaks when the moisture content is 10.5%, 10%, and 12%, respectively. With the increase of compaction, the τ, φ and c of SRM all increase. The effect of gradation on τ, φ and c is small.

scholarly journals Analysis of Internal Friction Angle and Cohesion Value for Road Base Materials in a Specified Gradation

2020 ◽  
Vol 3 (2) ◽  
pp. 58
Author(s):  
Grawira Ganjur Giwangkara ◽  
Azman Mohamed ◽  
Hasanan Md. Nor ◽  
Nur Hafizah A. ◽  
Rachmat Mudiyono
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Friction Angle ◽  
Recycled Concrete ◽  
Internal Friction Angle ◽  
Small Scale ◽  
Foundation Engineering ◽  
Direct Shear ◽  
Road Base ◽  
Factor C

Internal friction angle (φ) is one of the important parameter in a foundation engineering, especially in the stress distribution event. The higher value of the internal friction angle shows the higher of the material can withstand the lateral force. Cohesion factor (c) is also an integral part of the shear strength for the foundation material. In the granular soil such as sand or non-cohesive material, including aggregate, cohesion value usually assumed as zero, although some cohesion factor may be applied. In this research, two different materials were tested for their shear strength. The materials were Natural Crushed Aggregate (NCA) and Recycled Concrete Aggregate (RCA). Each material was also tested under two different circumstances. First, the materials were tested in a small-scale direct shear (SSDS) test with the maximum material size of 0.425 mm and 2.0 mm. Secondly, the materials were tested in a large-scale direct shear (LSDS) test with the graded size of aggregate according to road base layer specification. The SSDS showed the internal friction angle of NCA and RCA varies from 26.20 to 29.82 degrees. Whereas the LSDS showed the internal friction angle of NCA and RCA are 44.90 and 29.16 respectively. Both of SSDS and LSDS also showed the cohesion value of NCA and RCA.

Experimental Study on Shear Strength of Expansive Soil Improved by Lime - Weathered Sand

2013 ◽  
Vol 446-447 ◽  
pp. 1441-1447
Author(s):  
Meng Yun Huang ◽  
Jun Lai Xiong ◽  
Ji Bing Tang ◽  
Chi Long
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Direct Shear Test ◽  
Shear Test ◽  
Expansive Soil ◽  
Dry Density ◽  
Direct Shear ◽  
Mass Ratio ◽  
Angle Of Internal Friction ◽  
The Impact

This paper ananlyzes and contrasts the direct shear test of the expansive soil with different weathered sand dosage (mass ratio) and different lime dosage (mass ratio) in the case of the expansive soil with some water content and dry density .And try to analyzes and researches the impact of expansive soil improved by weathered sand and lime shear strength index . The direct shear test by the expansive soil mixed with different proportions of weathered sand and lime can be concluded that: mixing the weathered sand to improve the shear strength of expansive soil is effective, and cohesion gradually decreases with the increase of doped proportion of sand and the angle of internal friction first increases with the increase of doped proportion of sand and then decreases ;mixing of lime is effective to improve the shear strength of expansive soil, and cohesion gradually decreases with the increase of doped proportion of lime and angle of internal friction first increases and then decreases with the increase of doped proportion of lime. The shear strength of improved expansive soil can meet the subgrade filling with soil standards and at the same time the expansive soil improved by weathered sand and lime reduces the amount of lime and reduce project cost when to achieve the same shear strength standards.

Improvement of the Shear Strength Parameters of a Granular Volcanic Soil Using Type I Portland Cement

2021 ◽  
Vol 896 ◽  
pp. 165-172
Author(s):  
Jordy Frank Viso Chachayma ◽  
Jhian Franco Torres Alvarez ◽  
Gary Durán Ramírez ◽  
Carlos Mario Fernández Díaz
Keyword(s):  
Shear Strength ◽  
Direct Shear Test ◽  
Shear Test ◽  
Friction Angle ◽  
Natural Soil ◽  
Dry Density ◽  
Type I ◽  
Direct Shear ◽  
Volcanic Soil ◽  
Maximum Dry Density

The purpose of this research is to improve the parameters of shear strength in granular volcanic soil, by adding a percentage of Portland type I cement. The first step for this research was to classify the soil through a Granulometry test, according to the Unified Soil Classification System (USCS), the result was considered as a poorly graded sand with gravel also considered by The American Association of State Highway and Transportation Officials (AASHTO) as “A-1-b”. In addition, the compaction curve of the volcanic soil has a Maximum Dry Density (MDD) of 1.21 kg/cm2 and an optimum moisture content of 17.8%. Also, the friction angle of 33.5° and a cohesion of 0 kg/cm2, and the results of the Direct Shear Test indicate the Residual Stresses of 0.63, 1.34 and 2.65 kg/cm2 according to the Normal Stresses 1, 2 and 4 kg/cm2, respectively. The second step was to apply a Modified Proctor Test as following: one sample for natural soil and four samples adding 3%, 5%, 7% and 9% of cement. Finally, applied the Direct Shear Test: one sample for natural soil and three samples adding 3%, 5%, and 7% of cement after 7 days of curing, then three more samples are taken adding 3, 5% and 7% of cement at 14 days of curing. The results of the Modified Proctor Test of the volcanic soil with the addition of 5% cement has a maximum peak of a Maximum Dry Density of 1.33 kg/cm2 and with an Optimal Moisture Content of 22.7%, improved the MDD by 10% in regard to the natural soil. And the results of the Direct Shear Test shown in each sample an increase from 14.6% to 79.1% in the friction angle in comparison with the natural soil from 25.8% to 161.5% in shear strength. Likewise, the behavior of the volumetric deformation is shown, presenting a greater contraction when a normal stress of 1 kg/cm2 is applied and a greater expansion when a normal stress of 4 kg/cm2 is applied. Also, the volcanic soil at 7 days of curing with 7% cement addition increases its resistance by 67.34% and the volumetric variation decreases by 50% and the volcanic soil at 14 days of curing with 5% addition of cement increases its resistance by 103.40% and the volumetric variation decreases by 25%.

Effect of Particle Size and Shape Characteristics on Ballast Shear Strength: A Numerical Study Using the Direct Shear Test

2017 ◽  
Author(s):  
Debakanta Mishra ◽  
S. M. Naziur Mahmud
Keyword(s):  
Particle Size ◽  
Numerical Modeling ◽  
Shear Strength ◽  
Direct Shear Test ◽  
Shear Test ◽  
Direct Shear ◽  
Ongoing Research ◽  
Size And Shape ◽  
Particle Size And Shape ◽  
Shape Characteristics

The ballast layer serves as a major structural component in typical ballasted railroad track systems. When subjected to an external load, ballast particles present a complex mechanical response which is strongly dependent on particle to particle interactions within this discrete medium. One common test used to study the shear strength characteristics of railroad ballast is the Direct Shear Test (DST). However, it is often not feasible in standard geotechnical engineering laboratories to conduct direct shear tests on ballast particles due to significantly large specimen and test setup requirements. Even for the limited number of laboratories equipped to accommodate the testing of such large specimens, conducting repeated tests for parametric analysis of different test and specimen parameters on shear strength properties is often not feasible. Numerical modeling efforts are therefore commonly used for such parametric analyses. An ongoing research study at Boise State University is using the Discrete Element Method (DEM) to evaluate the effects of varying particle size and shape characteristics (i.e., flakiness, elongation, roundness, angularity) on direct shear strength behavior of railroad ballast. A commercially available three-dimensional DEM package (PFC3D®) is being used for this purpose. In numerical modeling, railroad ballasts can be simulated using spheres (simple approach) and non-breakable clumps (complex approach). This paper utilizes both approaches to compare the ballast stress-strain response as obtained from DST. Laboratory test results available in published literature are being used to calibrate the developed numerical models. This paper presents findings from this numerical modeling effort, and draws inferences concerning the implications of these findings on the design and construction of railroad ballast layers.

Sign in / Sign up

Export Citation Format

Share Document