scholarly journals Effects of Paving Technology, Pavement Materials, and Structures on the Fatigue Property of Double-Layer Pavements

2020 ◽  
Vol 2020 ◽  
pp. 1-15
Author(s):  
Changqing Deng ◽  
Yingjun Jiang ◽  
Zhanchuang Han ◽  
Hongwei Lin ◽  
Jiangtao Fan
Keyword(s):  
Surface Layer ◽  
Fatigue Life ◽  
Weibull Distribution ◽  
Double Layer ◽  
Asphalt Pavement ◽  
Bottom Layer ◽  
Asphalt Pavements ◽  
Fatigue Properties ◽  
Pavement Structure ◽  
Pavement Structures

Double-layer paving technology, which is a new technology for construction asphalt pavements, has received increasing research attention for several years. However, few studies have focused on the effect of asphalt pavement layer thickness and mixture-type combinations on the fatigue properties of a double-layer pavement. Therefore, the fatigue properties of the double-layer and traditionally paved asphalt pavements were studied in this work. The effects of two paving technologies, three mixture combinations, and two asphalt layer thickness combinations on the fatigue properties of asphalt pavements were studied through bending beam tests, and a fatigue equation of different asphalt pavements was established using the two-parameter Weibull distribution. Subsequently, the fatigue lives of different pavements were compared and analyzed under the same cyclic load. Results indicate that the flexural strength and fatigue life of the double-layer pavement increased by at least 10% and 54%, respectively, compared with those of a traditionally paved pavement structure. The goodness of fit of the equation established using the Weibull distribution exceeded 0.90. For the traditional paving technology, compared with the pavement structure combination of 4-cm AC-13 surface layer/6-cm AC-20 bottom layer, the fatigue life of a 3-cm AC-13 surface layer/7-cm AC-20 bottom layer can be increased by at least 8%, while the fatigue lives of other pavement structures are reduced significantly. The results also indicate that the fatigue life of the double-layer pavement structure with the 3-cm AC-13 surface layer/7-cm AC-20 bottom layer can be increased by at least 114% compared with that of the traditionally paved pavement structure (4-cm AC-13 surface layer/6-cm AC-20 bottom layer). Additionally, the fatigue lives of other pavement structures can be improved. To effectively improve the fatigue life of an asphalt pavement, a double-layer pavement structure with the 3-cm AC-13 surface layer/7-cm AC-20 bottom layer combination is recommended.

scholarly journals Long-Term Performance of Pavement Structures with Cold In-Place Recycled Base Course

2021 ◽  
Vol 16 (2) ◽  
pp. 48-65
Author(s):  
Audrius Vaitkus ◽  
Judita Gražulytė ◽  
Andrius Baltrušaitis ◽  
Jurgita Židanavičiūtė ◽  
Donatas Čygas
Keyword(s):  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Asphalt Pavements ◽  
Recycled Asphalt ◽  
Binding Agents ◽  
Pavement Structure ◽  
Pavement Structures ◽  
Base Course ◽  
Surface Distress ◽  
Foamed Bitumen

Properly designed and maintained asphalt pavements operate for ten to twenty-five years and have to be rehabilitated after that period. Cold in-place recycling has priority over all other rehabilitation methods since it is done without preheating and transportation of reclaimed asphalt pavement. Multiple researches on the performance of cold recycled mixtures have been done; however, it is unclear how the entire pavement structure (cold recycled asphalt pavement overlaid with asphalt mixture) performs depending on binding agents. The main objective of this research was to evaluate the performance of cold in-place recycled asphalt pavements considering binding agents (foamed bitumen in combination with cement or only cement) and figure out which binder leads to the best pavement performance. Three road sections rehabilitated in 2000, 2003, and 2005 were analysed. The performance of the entire pavement structure was evaluated in terms of the International Roughness Index, rut depth, and pavement surface distress in 2013 and 2017.

Sponge roads: the permeable asphalt pavement structures based on rainfall characteristics in central plains urban agglomeration of China

2019 ◽  
Vol 80 (9) ◽  
pp. 1740-1750 ◽  
Author(s):  
Xiaodong Guo ◽  
Jiupeng Zhang ◽  
Bochao Zhou ◽  
Wolong Liu ◽  
Jianzhong Pei ◽  
...  
Keyword(s):  
Surface Layer ◽  
Bearing Capacity ◽  
Asphalt Pavement ◽  
Structure Design ◽  
Urban Agglomeration ◽  
Central Plains ◽  
Rainfall Characteristics ◽  
Combination Scheme ◽  
Pavement Structure ◽  
Pavement Structures

Abstract Permeable asphalt pavement should be selected according to the rainfall characteristics of the project site, so as to improve the permeable performance and ensure the bearing capacity of the pavement structure. Therefore, taking a city in the central plains urban agglomeration of China as an example, the characteristics of the rainstorm intensity distribution and cumulative rainfall are analyzed, and a combination scheme of drainage surface layer asphalt pavement suitable for rainfall characteristics in this area is proposed. Then, the pavement structure design is systematically carried out based on the permeable capacity and bearing capacity. The results show that under the rainfall conditions in this area, there is no surface runoff on the permeable asphalt pavement with 120 mm drainage surface layer, which is suitable for the medium traffic grade of urban roads with cumulative equivalent axle loads of 10 million to 12 million times.

Technological Study on Interlayer Bonding of Double-Layer Porous Asphalt Pavement

2013 ◽  
Vol 405-408 ◽  
pp. 1725-1732 ◽  
Author(s):  
Guo Qi Tang ◽  
Dong Wei Cao ◽  
Ke Zhong ◽  
Xiao Qiang Yang
Keyword(s):  
Double Layer ◽  
Asphalt Pavement ◽  
Layer By Layer ◽  
Simulation Experiments ◽  
Porous Asphalt ◽  
One Step ◽  
Bonding Technology ◽  
Pavement Structure ◽  
Technological Study ◽  
Interlayer Bonding

The interlayer bonding of double-layer porous asphalt pavement will show more variations with different construction technologies, such as one-step molding by double-layer (hot on hot) paver, or paving layer by layer (hot on cold) with or without tack coat, and the variations will definitely have influences on pavement structure. Different interlayer technologies are studied in this paper on three levels including simulation experiments on specimen by indoor preparation, calculation of pavement mechanics, and construction of testing road, so that optimal interlayer bonding technology for double-layer porous asphalt pavement is discussed in combination with its effect on permeability.

scholarly journals The Influence of the Carbo-Glass Geogrid-Reinforcement on the Fatigue Life of the Asphalt Pavement Structure / Wpływ Zbrojenia Siatka Weglowo–Szklana Na Trwałosc Zmeczeniowa Asfaltowej Nawierzchni Drogowej

2012 ◽  
Vol 58 (1) ◽  
pp. 97-113 ◽  
Author(s):  
J. Górszczyk ◽  
S. Gaca
Keyword(s):  
Fatigue Life ◽  
Asphalt Pavement ◽  
Field Tests ◽  
Traffic Loading ◽  
Geogrid Reinforcement ◽  
Traffic Conditions ◽  
Pavement Structure ◽  
Number Of Cycles ◽  
The One ◽  
Stress Fatigue

Abstract This paper describes the analyses of the fatigue life of the asphalt pavement reinforced with geogrid interlayer under traffic loading. Finite Element ANSYS package with using nCode applications, as well as macros specially designed in APDL programming script and VBA were used to model the considered problem. Our analysis included computation of stress, fatigue life, damage matrix and rainflow matrix. The method applied was the one of fatigue calculation: stress - number of cycles in short S-N. On the basis of the performed high cycle fatigue analysis, the influence of the location of the used geogrid and of its bond with asphalt layers on the fatigue life and the work of the asphalt pavement structure were determined. The study was carried out for three temperature seasons i.e. spring and fall (assumed as one season), winter and summer. The variability of the traffic conditions were taken into account by assuming weekly blocks of traffic loading. The calculations were made using the real values of loading measured in field tests on the German highways by means of HS-WIM weighing system. As a result of the performed tests, it was proved that the use of geogrid-reinforcement may prolong the fatigue life of the asphalt pavement. However, it is required that: the geogrid should be located in the tension zone as low as possible in the structure of the asphalt layers. Moreover, it is necessary to provide high stiffness of the bond between the geogrid and the asphalt layers.

scholarly journals Development of a Full-Depth Wheel Tracking Test for Asphalt Pavement Structure: Methods and Performance Evaluation

2016 ◽  
Vol 2016 ◽  
pp. 1-7 ◽  
Author(s):  
Hui Wang ◽  
Zepeng Fan ◽  
Jiupeng Zhang
Keyword(s):  
Performance Evaluation ◽  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Single Layer ◽  
Test Method ◽  
Shanxi Province ◽  
Wheel Tracking Test ◽  
Pavement Structure ◽  
Pavement Structures ◽  
Wheel Tracking

The rutting performance of asphalt pavement structure relies on the high temperature properties of asphalt mixture as well as the pavement structure and thickness. In order to investigate the influence of the structure and thickness, a full-depth wheel tracking test is developed in this research by improving the conventional wheel tracking test apparatus. The newly proposed test method is capable of varying its load speed and load size, controlling its specimen temperature gradient, and simulating the support conditions of actual asphalt pavement. The full-depth wheel tracking test based rutting performance evaluation of different asphalt pavement structures indicates that it is not reasonable to explain the rutting performance of asphalt pavement structure from the point of view of single-layer asphalt mixture rutting performance. The developed full-depth wheel tracking test can be used to distinguish rutting performance of different asphalt pavement structures, and two of five typical asphalt pavement structures commonly used in Shanxi Province were suggested for use in practical engineering.

scholarly journals An Experimental Investigation on the Repairing Performance and Fatigue Life of Asphalt Pavement Potholes With an Inclined Interface Joint

2021 ◽  
Vol 7 ◽  
Author(s):  
Linyu Li ◽  
Yangquan Huang ◽  
Zhutao Shao ◽  
Dongya Ren
Keyword(s):  
Fatigue Life ◽  
Prediction Model ◽  
Structural Damage ◽  
Experimental Testing ◽  
Asphalt Pavement ◽  
Fatigue Behavior ◽  
Asphalt Pavements ◽  
Joint Interface ◽  
Tack Coat ◽  
Joint Shape

A pothole is a typical structural damage of asphalt pavements that significantly influence the life of asphalt pavements and driving safety. The durability of the existing pit repair methods is generally low. The existing studies in the context of pothole repair mainly focus on the selection and the amount of tack coat materials, nonetheless, very limited studies emphasize the effect of the joint interface shape. This study aims to investigate the influence of the interface joint shape on the service life of pothole repair by experimental testing. The strength and fatigue behavior of the joints were studied and the effectiveness of pothole repairs was evaluated under various conditions, including four temperature levels (5, 10, 15 and 25°C), four strain levels (750 με, 1,000 με, 1,250 με, and 1,500 με) and three loading frequencies (2, 5, and 10 Hz). The optimal interface joint shape was obtained by orthogonal tests. The results indicated that the bond strength and fatigue life of the high viscoelastic emulsified asphalt with an area density of 0.6 kg/m2 in the form of a 30° inclination joint was 473 and 80 times higher than those of traditional pothole repair (i.e., vertical joint form and no tack coat), respectively. Finally, a prediction model was proposed for the interface joint fatigue life considering external parameters through multiple regression analyses. This prediction model can provide a reference for the further study of asphalt pavement pothole repair.

scholarly journals Temperature Adaptability of Asphalt Pavement to High Temperatures and Significant Temperature Differences

2018 ◽  
Vol 2018 ◽  
pp. 1-16
Author(s):  
Xueying Zhao ◽  
Aiqin Shen ◽  
Baofu Ma
Keyword(s):  
Asphalt Pavement ◽  
Maximum Shear Stress ◽  
Structure Design ◽  
Temperature Fields ◽  
Asphalt Pavements ◽  
Fe Model ◽  
Tire Pressure ◽  
Significant Temperature ◽  
Pavement Structure ◽  
Temperature Adaptability

Temperature adaptability of asphalt pavements is very important, due to their potential influence on pavement structure design, particularly in areas that experience significant temperature differences. In this paper, a finite element (FE) model was developed, and Turpan-Xiaocao Lake Highway in southern Xinjiang was taken as a case study engineering, which tends to experience this adverse environmental condition (temperature difference: 25.5°C; July 14, 2008). In this model, the generalized Kelvin model and the Burgers model were used. The time-dependent tire pressure was considered. To guide pavement structure design and control pavement distresses in this area, seven alternative pavement structures were selected to simulate and analyze pavement temperature fields and the mechanical responses. It was observed that the influence of air temperature had the greatest impact on Str-1, possibly due to the thinnest asphalt course. Moreover, when rutting depth, maximum shear stress of the asphalt course, deflection on the pavement surface, and compressive strains at the subgrade top surface were taken as the evaluation indices, the adaptability of asphalt pavements using compound base courses had obvious advantage due to their strong absorption and reflection of load impact. The adaptability of seven structures analyzed in this paper decreased in the following order: Str-5 > Str-6 > Str-4 > Str-2 > Str-m > Str-1 > Str-3. In addition, it broke the traditional view that asphalt pavement with a flexible base had the poor ability on rutting resistance. Besides, it also suggests that when the thickness of asphalt courses was equivalent, increasing the thickness of chemical-treated base courses would help with the deformation resistance, and vice versa.

Influence Analysis of Crack Depth and Position on Asphalt Pavement Structure with 3D Finite Element

2012 ◽  
Vol 450-451 ◽  
pp. 267-272 ◽  
Author(s):  
Peng Wang ◽  
Can Cui
Keyword(s):  
Finite Element ◽  
Shear Stress ◽  
Shear Strength ◽  
Surface Layer ◽  
Tensile Stress ◽  
Asphalt Pavement ◽  
Top Down ◽  
Eccentric Load ◽  
3D Finite Element ◽  
Pavement Structure

In recent years the research on Surface-initiated longitudinal cracking along wheelpath (or Top-Down cracking) is become a fresh hotspot in the field of pavement damage focused by international asphalt pavement engineering.Because the traditional load is the vertical surface load with uniform tire pressure, this loading is applied at only one position and no effort is made to distinguish between tire pattern.The traditional method can’t explain the mechanism of the top-down cracking. In order to discuss the mechanism of TDC, this paper establish a 3D finite element model of semi-rigid pavement structure and use the large finite element software Abaqus. The analysis shows that, in the crack beginning stage, the main tensile stress appears under the center of the load on the sub-base of the pavement,and its value increases with the time. When cracks appear in the base, the position of the main tensile stress appears at the bottom of the surface layer, under the outside edge of wheel path. The value of the main shear stress increases at the stage of the cracks beginning, but the increase is small. The value of the main shear stress decreases when the cracks appear in the middle of the surface layer, and the position of the main shear stress changes with the depth of the cracks. With the increase of the cracks’ depth, the adverse influence of the shear stress becomes weaker and weaker.So the key of controlling the cracks in the surface layer is prevention. To prevent the development of the cracks, the tensile strength of the layer’s material should be enhanced in any way. The stress and its value resulted from the vehicle loaded on the structure layer is bigger than the other cases when the position of the cracks is at the edge of wheel path, and the stress is much bigger than the shear strength and the fracture toughness of the material of the layer. As the shear strength of the material is not enough, the vertical cracks are easier to appear at the edge of wheel path under the load of the vertical. Once it appearing, the cracks will extended into the layer because of the load of vertical. Eccentric load generates greater stress in the structure than the load loaded upright. In fact, though, non-channeling can reduce the appearance of the tracks, eccentric load enhance the development of the cracks in the surface because of the existence of the cracks in the surface layer.

Analysis of Perpetual Asphalt Pavement Response under Heavy Loads in Northeast Area of China

2013 ◽  
Vol 838-841 ◽  
pp. 1203-1215
Author(s):  
Deng Wen Zhou ◽  
Rong Jin Wang
Keyword(s):  
Finite Element ◽  
Contact Area ◽  
Asphalt Concrete ◽  
Asphalt Pavement ◽  
Asphalt Pavements ◽  
Rigid Base ◽  
Characteristic Finite Element ◽  
Pavement Structures ◽  
Heavy Loads ◽  
High Traffic Volume

Severe rutting, cracks and moisture damage are presented on conventional semi-rigid base asphalt pavements not long after completed in China. This phenomenon indicates that conventional philosophy on pavement design could not meet more and more frequent and heavy vehicle. With high structural capacity for high traffic volume and heavy loads, the Perpetual Asphalt Pavements (PAPs) solve those problems well. Meanwhile they need minimal or no major structural rehabilitation and/or reconstruction exercises in their life, which ensures low user-delay. Three PAPs, including semi-rigid base asphalt pavement, flexible base asphalt pavement, and combined base asphalt pavement, are put forward for the northeast area in China considering its climate, traffic characteristic. Finite element method is utilized to analyze response of PAPs under heavy loads. Two key factors, i.e. tensile horizontal strains at the bottom of asphalt layers and compressive vertical strains are investigated. Also the capacities of the structures on bearing overloading are estimated. Four types of wheel and axle, including single axle and single tire, single axle and dual tires, dual axles and dual tires, and tri axles and dual tires are adopted in finite element models. The shapes of tire-pavement contact area are either circular or rectangular to simulate standard load or overloading respectively. When rectangular shapes are adopted, the contact area sizes and the distribution of pressure are varied. Conventional asphalt concrete and high modulus asphalt concrete are adopted. Simulations are done. The competences of the three pavement structures on fulfilling long lives are evaluated.

Sign in / Sign up

Export Citation Format

Share Document