Effect of Glass Cullet Size and Hydrated Lime—Nanoclay Additives on the Mechanical Properties of Glassphalt Concrete

In this study, the use of glass waste as aggregate in asphalt mixtures was investigated. Maximum glass aggregate size options of 0.075, 2.00, 4.75 and 9.5 mm. were selected. Conventional bitumen, nanoclay-modified bitumen and hydrated lime-modified bitumen were used. Dense graded asphalt mixtures were designed according to the Marshall method. Mixtures were evaluated for low-temperature cracking, resistance to water damage, fatigue, and permanent deformation behavior with repeated creep, indirect tensile strength, indirect tensile fatigue, modified Lottman and Hamburg wheel tracking tests. Increasing glass aggregate size reduced the water damage resistance of asphalt mixtures because of the smooth surface of the glass particles and nanoclay and hydrated lime modification improved the mechanical properties of the asphalt mixtures. Using 2.00 mm sized maximum glass aggregate showed relatively less water damage and deformation properties due to higher internal friction which is due to the greater angularity of the glass particles. In addition, there was a significant correlation between repeated creep test, modified Lottman methods and Hamburg Wheel tracking test from the viewpoint of deformation and water damage assessments.

Study on the Optimum Steel Slag Content of SMA-13 Asphalt Mixes Based on Road Performance

To reduce the use of aggregates such as limestone and basalt, this paper used steel slag to replace some of the limestone aggregates in the production of SMA-13 asphalt mixes. The optimum content of steel slag in the SMA-13 asphalt mixes was investigated, and the performance of these mixes was evaluated. Five SMA-13 asphalt mixes with varying steel slag content (0%, 25%, 50%, 75%, and 100%) were designed and prepared experimentally. The high-temperature stability, low-temperature crack resistance, water stability, dynamic modulus, shear resistance, and volumetric stability of the mixes were investigated using the wheel tracking, Hamburg wheel tracking, three-point bending, freeze–thaw splitting, dynamic modulus, uniaxial penetration, and asphalt mix expansion tests. The results showed that compared to normal SMA-13 asphalt mixes, the high-temperature stability, water stability, and shear resistance of the SMA-13 asphalt mixes increased and then decreased as the steel slag content increased. All three performance indicators peaked at 75% steel slag content, and the dynamic stability, freeze–thaw splitting ratio, and uniaxial penetration strength increased by 90.48%, 7.39%, and 88.08%, respectively; however, the maximum bending tensile strain, which represents the low-temperature crack resistance of the asphalt mix, decreased by 5.98%. The dynamic modulus of the SMA-13 asphalt mixes increased with increasing steel slag content, but the volume expansion at a 75% steel slag content was 0.446% higher than at a 0% steel slag content. Based on the experimental results, the optimum content of steel slag for SMA-13 asphalt mixes was determined to be 75%.

Laboratory Evaluation of Mechanical Properties of Modified Asphalt and Mixture Using Graphene Platelets (GnPs)

Recently, nanomaterials have attracted attention in the field of pavement construction as modifiers to endure heavy loads and climate changes. In this study, conventional asphalt (bitumen) of penetration grade AC (60/70) was modified with graphene platelets (GnPs) at three different contents: 0.5%, 1.0%, and 1.5% by weight of asphalt content. Kinematic viscosity, softening point, penetration, and dynamic shear rheology tests were performed to evaluate the mechanical properties of modified binder. The results showed that adding GnPs improves the mechanical properties of asphalt binder; the kinematic viscosities, softening points, and rutting parameters increased but penetrations decreased with the contents of GnPs. Hot mix asphalt specimens with GnPs-modified asphalt were prepared and characterized with Marshall tests, thermal stress restrained specimen tests (TSRST), wheel tracking tests, and indirect tensile tests. Similar to the results of asphalt binder, the mechanical properties of asphalt mixture were improved by GnPs. Marshall stability increased by 21% and flow decreased by 24% with accepted value of 2.8 mm in penetration when the mixture was modified with 1.0 wt% of GnPs. At the same GnPs content, modified asphalt mixture led to lower failure temperature by 2 °C in comparison with unmodified asphalt mixture and the cryogenic failure stress was improved by 12%. The wheel tracking tests showed that GnPs-modified asphalt mixture has outstanding deformation resistance in comparison with unmodified asphalt mixtures: after 5000 cycles, 1.0 wt% of GnPs reduced the rut depth of asphalt mixture by 60%—the rut depth of unmodified asphalt mixture was 6.9 mm compared to 2.75 mm for modified asphalt mixture. After 10,000 cycles, the modified asphalt mixture showed rut depth of 3.24 mm in comparison with 8.12 mm in case of unmodified asphalt mixture. Addition of GnPs into asphalt mixture significantly improved the indirect tensile strength: 1.0 wt% of GnPs increased the indirect tensile strength of unmodified asphalt mixture from 0.79 to 1.1 MPa recording ~40% increment. The results of this study can confirm that graphene platelets enhance the mechanical properties of asphalt mixture and its performance.

Performance Evaluation of Bioengineered Recyled Asphalt Materials

In this study, asphalt mixtures were engineered with bio-renewable soybean oil-derived modifiers, and then used for pavement demonstration projects in the U.S. states of Iowa and Minnesota in the summer of 2019. The performance grade, elastic recovery (R), and non-recoverable creep compliance (Jnr) of the binders were evaluated. The modification of asphalt binder for the Iowa project almost maintained the high and low temperature grades, and the presence of modifier in the mixture of Minnesota project resulted in a slight decrease in the low temperature grade while maintaining the high temperature grade. The Jnr and R values proved the increase of elasticity and relaxation of the asphalt binder modified for the Iowa project. The Jnr calculated for the Minnesota project revealed a considerable increase in the relaxation of the asphalt binder. Disc-shaped compact tension, Hamburg wheel tracking, and push-pull were the mechanical performance tests performed on the mixtures. Based on the results obtained from these tests, the Iowa mixture, produced with modified asphalt binder, showed a significant improvement in resistance to low-temperature cracking, rutting, moisture damage, and fatigue cracking. The Minnesota mixture, modified in the plant, showed a significant improvement in the fatigue performance and a slight improvement in low-temperature cracking resistance.

Effectiveness of Loaded Wheel Tracking Test to Ascertain Moisture Susceptibility of Asphalt Mixtures

Moisture damage of asphalt mixtures is a major distress affecting the durability of asphalt pavements. The loaded wheel tracking (LWT) test is gaining popularity in determining moisture damage because of its ability to relate laboratory performance to field performance. However, the accuracy of LWT’s “pass/fail” criteria for screening mixtures is limited. The objective of this study was to evaluate the capability of the LWT test to identify moisture susceptibility of asphalt mixtures with different moisture conditioning protocols. Seven 12.5 mm asphalt mixtures with two asphalt binder types (unmodified PG 67-22 and modified PG 70-22), and three aggregate types (limestone, crushed gravel, and a semi-crushed gravel) were utilized. Asphalt binder and mixture samples were subjected to five conditioning levels, namely, a control; single freeze–thaw-; triple freeze–thaw-; MiST 3500 cycles; and MiST 7000 cycles. Frequency sweep at multiple temperatures and frequencies, and multiple stress creep recovery tests were performed to evaluate asphalt binders. LWT test was used to evaluate the asphalt mixture samples. Freeze–thaw and MiST conditioning resulted in an increase in stiffness in the asphalt binders as compared with the control. Further, freeze–thaw and MiST conditioning resulted in an increase in rut depth compared with the control asphalt mixture. The conditioning protocols evaluated were effective in exposing moisture-sensitive mixtures, which initially showed compliance with Louisiana asphalt mixture design specifications.

Empirical correlation of the Modified Wheel Tracker (MWT) and the dynamic creep test for evaluating the permanent deformation of HMA

The Wheel Tracking Test (WTT) has been extensively used for laboratory characterization of permanent deformation of Hot Mix Asphalt (HMA). However, the fully-confined setup of the device is unable to capture the tertiary zone where shear deformation takes place. This makes the permanent deformation resistance characteristics of HMA difficult to analyze. Hence, a modified wheel tracker (MWT), with unconfined lateral sides along the wheel tracking direction was utilized in this study, which can capture the tertiary flow [referred to as the Flow Number (FN)]. The dynamic creep test, which yields FN, is a common laboratory test which has the ability to characterize permanent deformation considering the shear behavior. The study investigated the relationship of the MWT and the dynamic creep test utilizing the permanent deformation and permanent micro-strain data from the respective tests. A novel parameter, FN-Index was explored. The permanent deformation parameters derived from the MWT were well correlated with the dynamic creep test. The MWT showed promising repeatability for the FNs.