scholarly journals Study on Mechanical Properties and Energy Dissipation of Frozen Sandstone under Shock Loading

2020 ◽  
Vol 2020 ◽  
pp. 1-12
Author(s):  
Lei Wang ◽  
Yue Qin ◽  
Haibin Jia ◽  
Hongming Su ◽  
Shiguan Chen

In order to understand the mechanical properties and energy dissipation law of frozen sandstone under impact loading, the cretaceous water-rich red sandstone was selected as the research object to conduct impact tests at different freezing temperatures (0°C, −10°C, −20°C, and −30°C). The test results suggested the following: (1) the peak stress and peak strain of frozen sandstone are positively correlated with strain rate and freezing temperature, and the strain rate strengthening effect and the low-temperature hardening effect are obvious. (2) The strain rate sensitivity of dynamic stress increase factor (DIF) is negatively correlated with temperature. Water-ice phase change and the difference in the cold shrinkage rate of rock matrix under strong impact loading will degrade the performance of rock together, so DIF is less than 1. (3) In the negative temperature range from −10°C to −30°C, DEIF is always greater than 1. The energy dissipation rate of red sandstone specimens fluctuated between 10% and 25% under the impact loading, and the data are discrete, showing obvious strain rate independence. The failure form changes from tensile failure to shear and particle crushing failure. (4) Combined with the micromechanism analysis, the difference in dynamic mechanical properties of red sandstone at different temperatures is caused by the water-ice phase change and the different cold shrinkage rates of the frozen rock medium. When the temperature drops from 0°C to −2°C, water migrates to the free space of the pore of frozen rock and freezes into ice crystal, resulting in frozen shrinkage. At −30°C, the expansion of ice dominates and the migration of water will stop, leading to frost heave.

2020 ◽  
Vol 10 (21) ◽  
pp. 7525
Author(s):  
Zhehao Lu ◽  
Wenyuan Yan ◽  
Pengfei Yan ◽  
Biao Yan

The objective of the study is to investigate the strengthening mechanism of embedded meta-precipitates in the design of architected metamaterials. Four precipitate-type architected metamaterials are designed and prepared by fused deposition modelling (FDM). The difference of mechanical properties and deformation mode of these structures is analyzed. The strengthening effect of the introduced meta-precipitates is then compared with Orowan bypass strengthening mechanism. The similarities and discrepancies of metallurgical hardening principles and that found in architected metamaterials are established. It is found that due to the introduction of embedded meta-precipitates, the deformation of the structure changes significantly from diagonal crushing to a meander route, thus improves the mechanical properties and energy absorption abilities. The hindering effect and the influence of volume fraction of meta-precipitates is similar to Orowan bypass mechanism.


2014 ◽  
Vol 24 (2) ◽  
pp. 151-156 ◽  
Author(s):  
Ming Li ◽  
Xianbiao Mao ◽  
Aihong Lu ◽  
Jing Tao ◽  
Guanghui Zhang ◽  
...  

2016 ◽  
Vol 28 (5) ◽  
pp. 055702 ◽  
Author(s):  
Jason Ivall ◽  
Gabriel Langlois-Rahme ◽  
Sylvain Coulombe ◽  
Phillip Servio

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Wei Wang ◽  
Shifan Liu ◽  
Chong Shi ◽  
Shanxi Zheng ◽  
Qizhi Zhu

In this research, the conventional triaxial compression experiments for intact red sandstone specimens and the specimens with a single persistent joint at different inclination angles, i.e., 0°, 30°, 45°, and 90°, were conducted at first. Based on the results of the conventional tests, the effects of the confining pressure and the joint inclination angle on the mechanical properties including deformation behavior and strength parameters were summarized and analyzed, respectively. We find that the strength and deformation of jointed red sandstone are enlarged due to the increment of confining pressure, and the mechanical parameters of specimens show a U-shaped development with the rise of the joint angle. Besides, to investigate the effects of the pore pressure on seepage characteristics of rocks with joint angles at 0°, 45°, and 90°, a series of triaxial compression drainage tests on the jointed red sandstone were performed. The results show that the pore pressure has a weakening effect on the strength of jointed specimens, which can reduce the strengthening effect induced by confining pressure. Meanwhile, the tested specimens mostly present shear failure modes. As a result, the mechanical responses, seepage characteristics, and cracking modes in red sandstone containing a single persistent joint under triaxial compression are revealed.


Author(s):  
Yu-Kai Weng ◽  
Seungha Shin ◽  
Kenneth D. Kihm ◽  
Mohammad Bahzad ◽  
Douglas S. Aaron

2020 ◽  
Vol 27 (08) ◽  
pp. 1950191
Author(s):  
TAO WANG ◽  
WEILIN QIAO ◽  
SHENG WANG ◽  
ZHAN LI ◽  
HAO WANG ◽  
...  

The dynamic mechanical properties of Ti-6Al-4V alloy prepared by laser direct deposition (LDD) at different strain rates are of great significance for the application of LDD technology in the manufacture and repair of aero-engine parts. The quasi-static tensile test and dynamic compression test of Ti-6Al-4V alloy prepared by LDD (LDD-Ti-6Al-4V) were carried out under the quasi-static and high strain rate using INSTRON-5982 tensile test equipment and Split Hopkinson pressure bar (SHPB) equipment. The true stress–strain curve is obtained, which indicates that the LDD-Ti-6Al-4V has a strain rate strengthening effect. Moreover, the Johnson–Cook (J–C) constitutive model of LDD-Ti-6Al-4V was fitted based on experimental data, and the experimental process of SHPB was numerically simulated. The simulation results are basically the same as the experimental results, which proves the correctness of the J–C constitutive model of LDD-Ti-6Al-4V.


2021 ◽  
Vol 252 ◽  
pp. 02058
Author(s):  
Libo Pan ◽  
Wanjun Zhu ◽  
Zhaojun Deng ◽  
Zhijiang Zuo

TRIP effect is one of the important features for TRIP steel. A Nb-Mo microalloyed TRIP steel was developed by employing two different soaking time during annealing, and tensile tests at three different strain rate for specimens after annealing were performed. The microstructures and the volume fraction of retained martensite were examined and analyzed. The result indicated that TRIP steel showed significantly different behaviour at different strain rates. The ultimate tensile strength and total elongation decreased with the strain rate increasing. The dynamic strain aging effect might occur at low strain rate. With shorter soaking time during annealing, microstructure with ultra-refined grain size could be achieved. Fracture surfaces were different at different strain rate. As strain rate increases, the fraction of retained austenite to martensite transformation at failure point decreases which leads to the difference of mechanical properties.


Sign in / Sign up

Export Citation Format

Share Document