scholarly journals Investigation on Rock Strata Fracture Regulation and Rock Burst Prevention in Junde Coal Mine

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Fengnian Wang ◽  
Gan Li ◽  
Chi Liu
Keyword(s):  
Rock Burst ◽  
Coal Mine ◽  
Coal Pillar ◽  
Energy Concentration ◽  
Pressure Relief ◽  
Rock Stratum ◽  
Mechanics Model ◽  
Bending Elasticity ◽  
Mine Roadway ◽  
Rock Strata

Through the establishment of structural mechanics model, this paper analyzes the fracture of super thick rock stratum. Through the model, it can be seen that the fracture of low-level super thick rock stratum produces large elastic energy release and dynamic load, which is easy to produce disasters such as rock burst. The numerical calculation shows that under the influence of low hard and thick rock stratum, the leading area of coal mine roadway will produce energy concentration, and the coal pillar will also produce energy accumulation. Thick rock stratum is in bending state and has large bending elasticity. Coal pillar has large compression elasticity, which is the main reason for rock burst. The accumulation of elastic properties of overburden and rock burst caused by coal pillar energy storage can be effectively controlled by using advanced presplitting blasting, coal seam drilling pressure relief, and strengthening support.

scholarly journals Research on Evaluation Index and Application of Rockburst Risk in Deep Strip Mining

2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Bangyou Jiang ◽  
Hongguang Ji ◽  
Long Fu ◽  
Shitan Gu ◽  
Tong Zou ◽  
...  
Keyword(s):  
Plastic Zone ◽  
Coal Mine ◽  
Coal Pillar ◽  
Width Ratio ◽  
Strip Mining ◽  
Index Method ◽  
Research On Evaluation ◽  
Mechanics Model ◽  
Evolution Characteristics ◽  
Comprehensive Index Method

The practice shows that deep strip mining induces rockburst disaster easily. Accurately evaluating rockburst risk of the strip coal pillar is of great significance for ensuring the safety of deep strip mining. In this paper, the catastrophe mechanics model was used to analyze the abrupt instability condition of strip coal pillar. And the three indicators that are the medium stiffness ratio (k) of the elastic and plastic zone in the coal pillar, the plastic zone width ratio (aY), and the elastic deformation index (Uq) of core zone were put forward with considering the geometry size of coal pillar. Based on the 3202 panel of Gucheng Coal Mine, the evolution characteristics of rockburst risk of coal pillar under different mining widths and coal pillar widths were studied by numerical simulation. The evaluation result shows that the strip coal pillar of the 3202 panel is in danger of strong rockburst, which is more in line with the actual situation than the results of the traditional rockburst tendency identification test and comprehensive index method. These three indicators can be regarded as important indicators to evaluate the rockburst risk in the strip mining engineering field. Based on that, the design principle of strip mining in Gucheng Coal Mine was put forward, which is considered an important reference for similar cases.

scholarly journals Study on the Mechanism and Control of Rock Burst of Coal Pillar under Complex Conditions

Geofluids ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-19
Author(s):  
Xingping Lai ◽  
Huicong Xu ◽  
Jingdao Fan ◽  
Zeyang Wang ◽  
Zhenguo Yan ◽  
...  
Keyword(s):  
Stress Concentration ◽  
Rock Burst ◽  
Coal Mine ◽  
High Stress ◽  
Coal Pillar ◽  
Vertical Stress ◽  
Body Area ◽  
High Stress Concentration ◽  
Solid Coal ◽  
Working Face

In order to explore the mechanism of coal pillar rock burst in the overlying coal body area, taking W1123 working face of Kuangou Coal Mine as the engineering background, the full mining stage of W1123 is simulated by FLAC3D. It is found that the high stress concentration area has appeared on both sides of the coal pillar when W1123 does not start mining. With the advance of the working face, the high stress concentration area forms X-shaped overlap. There is an obvious difference in the stress state between the coal pillar under the solid coal and the coal pillar under the gob in W1123. The concrete manifestation is that the vertical stress of the coal pillar below the solid coal is greater than the vertical stress of the coal pillar below the gob. The position of the obvious increase of the stress of the coal pillar in the lower part of the solid coal is ahead of the advancing position of the working face, and the position of the obvious increase of the stress of the lower coal pillar in the gob lags behind the advancing position of the working face. At the same time, in order to accurately reflect the true stress environment of coal pillars, the author conducted a physical similarity simulation experiment in the laboratory to study the local mining process of the W1123 working face, and it is found that under the condition of extremely thick and hard roof, the roof will be formed in the gob, the mechanical model of roof hinged structurer is constructed and analyzed, and the results show that the horizontal thrust of roof structure increases with the increase of rotation angle. With the development of mining activities, the self-stable state of the high stress balance in the coal pillar is easily broken by the impact energy formed by the sudden collapse of the key strata. Therefore, the rock burst of coal pillar in the overlying coal body area is the result of both static load and dynamic load. In view of the actual situation of the Kuangou Coal Mine, the treatment measures of rock burst are put forward from the point of view of the coal body and rock mass.

Microseismic Precursory Characteristics of Rock Burst Hazard in Mining Areas Near a Large Residual Coal Pillar: A Case Study from Xuzhuang Coal Mine, Xuzhou, China

2016 ◽  
Vol 49 (11) ◽  
pp. 4407-4422 ◽  
Author(s):  
An-ye Cao ◽  
Lin-ming Dou ◽  
Chang-bin Wang ◽  
Xiao-xiao Yao ◽  
Jing-yuan Dong ◽  
...  
Keyword(s):  
Rock Burst ◽  
Coal Mine ◽  
Coal Pillar ◽  
Mining Areas ◽  
Burst Hazard ◽  
Residual Coal

scholarly journals Analysis on Rock Burst Risks and Prevention of a 54 m-Wide Coal Pillar for Roadway Protection in a Fully Mechanized Top-Coal Caving Face

2021 ◽  
Vol 2021 ◽  
pp. 1-7
Author(s):  
Zhihua Li ◽  
Ke Yang ◽  
Jianshuai Ji ◽  
Biao Jiao ◽  
Xiaobing Tian
Keyword(s):  
Coal Seam ◽  
Rock Burst ◽  
Influencing Factors ◽  
Abutment Pressure ◽  
Large Diameter ◽  
Coal Pillar ◽  
Distribution Characteristics ◽  
Pressure Relief ◽  
Working Face ◽  
Coal Pillars

A case study based on the 401103 fully mechanized caving face in the Hujiahe Coal Mine was carried out in this research to analyze the rock burst risks in a 54 m-wide coal pillar for roadway protection. Influencing factors of rock burst risks on the working face were analyzed. Stress distribution characteristics on the working face of the wide coal pillar for roadway protection were discussed using FLAC3D numerical simulation software. Spatial distribution characteristics of historical impact events on the working face were also investigated using the microseismic monitoring method. Results show that mining depth, geological structure, outburst proneness of coal strata, roof strata structure, adjacent mining area, and mining influence of the current working face are the main influencing factors of rock burst on the working face. Owing to the collaborative effects of front abutment pressure of the working face and lateral abutment pressure in the goaf, the coal pillar is in the ultimate equilibrium state and microseismic events mainly concentrate in places surrounding the coal pillars. Hence, wide coal pillars become the regions with rock burst risks on the working face. The working face adopts some local prevention technologies, such as pressure relief through presplitting blasting in roof, pressure relief through large-diameter pores in coal seam, coal seam water injection, pressure relief through large-diameter pores at bottom corners, and pressure relief through blasting at bottom corners. Moreover, some regional prevention technologies were proposed for narrow coal pillar for roadway protection, including gob-side entry, layer mining, and fully mechanized top-coal caving face with premining top layer.

scholarly journals Stress Relief and Support for Stability of Deep Mining Roadway with Thick Top Coal in Hujiahe Coal Mine with the Risk of Rock Burst

2021 ◽  
Vol 2021 ◽  
pp. 1-16
Author(s):  
Wenjing Liu ◽  
Deyu Qian ◽  
Xingguo Yang ◽  
Sujian Wang ◽  
Jinping Deng ◽  
...  
Keyword(s):  
Rock Burst ◽  
Coal Mine ◽  
Large Diameter ◽  
Stability Control ◽  
Surrounding Rock ◽  
Shaanxi Province ◽  
Pressure Relief ◽  
Working Face ◽  
Deformation Speed ◽  
Plastic Transformation

Rock burst is a typical dynamic disaster in deep underground coal mining. Based on the support problems of the deep roadways in fully mechanized caving face 401111 of Hujiahe Coal Mine suffering from rock burst in Shaanxi Province of China, the failure law and influencing factors of the surrounding rock of the roadway are analyzed. The results show that the deformation of surrounding rock in the roadway shows the characteristics of elastic, plastic transformation, rheology, and expansion. At the same time, it has the typical characteristics of deep roadway, such as the fast deformation speed, long duration, asymmetric deformation, and large loose broken area of surrounding rock. Based on the principle of “strengthening support in shallow zones” and “deep pressure relief in deep zones” in the surrounding rock, the control scheme of surrounding rock in the return roadway of fully mechanized caving working face 401111 is proposed by taking the large diameter pressure relief and deep hole blasting as the main means of pressure relief. The practice shows that the surrounding rock of the return roadway is relatively stable after the implementation of the new scheme, which shows that the design of the new support scheme is reasonable and reliable. It is of great significance for the stability control of surrounding rock of the mining roadway suffering from rock burst.

scholarly journals Determination of fracture location of double-sided directional fracturing pressure relief for hard roof of large upper goaf-side coal pillars

2019 ◽  
Vol 38 (1) ◽  
pp. 111-136 ◽  
Author(s):  
Jiangwei Liu ◽  
Changyou Liu ◽  
Xuehua Li
Keyword(s):  
Hydraulic Fracturing ◽  
Coal Mine ◽  
High Stress ◽  
Coal Pillar ◽  
Local Stress ◽  
Pressure Relief ◽  
Directional Hydraulic Fracturing ◽  
Fracture Location ◽  
Hard Roof ◽  
Coal Pillars

After mining the upper-goaf side, large coal pillars and part of hard roof exposed above the pillars remain. The hard roof can significantly deform the roadway by transferring high stress through coal pillars to the roadway. This paper reports the use of hydraulic fracturing technology to cut the hard roof on both sides (i.e. the broken roof slides to the goaf) to relieve the pressure. The position of the roof fracture is the key to controlling the pressure relief. The bearing characteristics of the large coal pillars and hard roof are analyzed to establish a mechanical model of the broken-roof sliding instability after directional fracturing and determine the width of the coal pillars that can collapse under maximum overburden load on coal pillars as a reasonable hydraulic fracturing position. The results show that the distance from the mine gateway to the fracture location increases with increasing hard-roof length, coal pillar depth, coal pillar thickness (mining height), and goaf width. In addition, the distance to the mine gateway decreases with increasing coal strength, support of the coal pillar by the anchor rod, cohesive force, and internal friction angle of the coal–rock interface. Engineering tests were applied in coal roadway 5107 of coal seam 5# of the Baidong Coal Mine of the Datong Coal Mine Group. Given the site conditions, a reasonable fracturing length of 8.8 m was obtained. Next, directional hydraulic fracturing was implemented. The comparison of the roof deformation before and after fracturing suggests that this method reduces the local stress concentration in coal pillars, which allows the surrounding rock deformation in roadway 5107 to be controlled.

scholarly journals Investigation of Pressure Relief Borehole Effects Using In Situ Testing Based on Distributed Optical Fibre Sensing Technology

2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Yunpeng Li ◽  
Dequan Sun ◽  
Shankun Zhao ◽  
Kaihua Liang ◽  
Kai Cui ◽  
...  
Keyword(s):  
Rock Burst ◽  
Coal Mine ◽  
Pressure Relief ◽  
Optical Time Domain Reflectometer ◽  
Sensing Technology ◽  
Optical Time ◽  
Different Diameters ◽  
First Time ◽  
Time Domain Reflectometer

Borehole pressure relief method is one of the most effective ways of rock burst prevention in coal mines. The measured results of borehole pressure relief at no. 8939 longwall face in Xinzhouyao coal mine, China, are presented here. The analyses identify the pressure relief magnitudes in coal mass around the boreholes with different diameters, spacing, and drilling time. This research has established that the best pressure relief of the rib coal can be achieved by using φ108 mm borehole with 0.7 m interval after 288 hours. The strain relief is acceptable after 288–360 hours of drilling, while the best result is achieved after 432 hours. It is also the first time to monitor the borehole pressure relief in a coal mine on-site using Brillouin optical time domain reflectometer (BOTDR) distributed fibre-optic sensing. The method implemented in this research provides new ways to improve stress relief design and minimize the rock burst occurrence for mine practitioners.

scholarly journals Reasonable Determination of Terminal Mining Lines Using the Stress Field with Seismic Wave Excitation in Deep Coalfaces

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
Guang-an Zhu ◽  
Huan Liu ◽  
Bo-ru Su ◽  
Qi-peng Jiang ◽  
Hai-yang Liu
Keyword(s):  
Stress Field ◽  
Theoretical Analysis ◽  
Rock Burst ◽  
Seismic Wave ◽  
Coal Mine ◽  
Evaluation Method ◽  
Coal Pillar ◽  
Field Observations ◽  
Wave Excitation ◽  
Rock Burst Risk

Many field observations have shown that rock bursts occur frequently near the terminal mining line (TML) and dip coal pillar area in deep coalfaces. Taking the “7.26” rock burst in coalface 3302 in Xingcun Coal Mine as an example, the rock burst mechanism was investigated based on theoretical analysis and field observations, and a combined evaluation method using the stress field under seismic wave excitation was established to determine the reasonable TML of coalface 3302. Firstly, the static geological data revealed during roadway excavation were used for preevaluation of rock burst risk at the working face. By theoretically analyzing the stress transfer mechanism of the two types of the roof structure, the computational model of abutment pressure was established and the calculation method giving the abutment stress was proposed. Subsequently, a dynamic evaluation method that adopts microseismic and stress online monitoring system to monitor dynamic information, such as mine tremors and stress during coalface mining, was developed to define stress anomaly areas and then dynamically determine the TML. Finally, the proposed model was used to optimize the position of the TML of LW3302 in Xingcun Coal Mine; findings obtained in this study provide theoretical guidance for safe coal mining. Combined with the results of theoretical analysis (255 m), online stress monitoring (200 m), microseismic (MS) monitoring (262 m), and passive seismic velocity tomography (220–250 m), it can be finally determined that the width of the protective coal pillar for the TML of coalface 3302 should be at least 262 m.

Sign in / Sign up

Export Citation Format

Share Document