scholarly journals Mechanism of Enhanced Oil Recovery for In-Depth Profile Control and Cyclic Waterflooding in Fractured Low-Permeability Reservoirs

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Daiyin Yin ◽  
Wei Zhou
Keyword(s):  
Enhanced Oil Recovery ◽  
Depth Profile ◽  
Oil Recovery ◽  
Water Injection ◽  
High Water ◽  
Low Permeability ◽  
Profile Control ◽  
High Water Cut ◽  
Water Cut ◽  
Low Permeability Reservoirs

When fractured low-permeability reservoirs enter a high water cut period, injected water always flows along fractures, water cut speeds increase rapidly, and oil production decreases quickly in oil wells. It is difficult to further improve the oil recovery of such fractured low-permeability reservoirs. In this paper, based on the advantages of in-depth profile control and cyclic water injection, the feasibility of combining deep profile control with cyclic water injection to improve oil recovery in fractured low-permeability reservoirs during the high water cut stage was studied, and the mechanisms of in-depth profile control and cyclic waterflooding were investigated. According to the characteristics of reservoirs in Zone X, as well as the fracture features and evolution mechanisms of the well network, an outcrop plate fractured core model that considers fracture direction was developed, and core displacement experiments were carried out by using the HPAM/Cr3+ gel in-depth profile control system. The enhanced oil recovery of waterflooding, cyclic water injection, and in-depth profile control, as well as a combination of in-depth profile control and cyclic water injection, was investigated. Moreover, variations in the water cut degree, reserve recovery percentage, injection pressure, fracture and matrix pressure, and water saturation were monitored. On this basis, the mechanism of enhanced oil recovery based on the combined utilization of in-depth profile control and cyclic waterflooding methods was analyzed. The results show that in-depth profile control and cyclic water injection can be synchronized to further increase oil recovery. The recovery ratio under the combination of in-depth profile control and cyclic water injection was 1.9% higher than that under the in-depth profile control and 5.6% higher than that under cyclic water injection. The combination of in-depth profile control and cyclic water injection can increase the reservoir pressure; therefore, the fluctuation of pressure between the matrix and its fractures increases, more crude oil flows into the fracture, and the oil production increases.

scholarly journals New prediction method for transient productivity of fractured five-spot patterns in low permeability reservoirs at high water cut stages

Open Physics ◽  
2018 ◽  
Vol 16 (1) ◽  
pp. 499-508
Author(s):  
Chuanzhi Cui ◽  
Zhongwei Wu ◽  
Zhen Wang ◽  
Jingwei Yang ◽  
Yingfei Sui
Keyword(s):  
Prediction Method ◽  
Mass Conservation ◽  
High Water ◽  
Low Permeability ◽  
Element Analysis ◽  
Fracture Length ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut ◽  
Low Permeability Reservoirs

AbstractPredicting the productivity of fractured five-spot patterns in low permeability reservoirs at high water cut stages has an important significance for the development and optimization of reservoirs. Taking the reservoir heterogeneity and uneven distribution of the remaining oil into consideration, a novel method for predicting the transient productivity of fractured five-spot patterns in low permeability reservoirs at high water cut stages is proposed by using element analysis, the flow tube integration method, and the mass conservation principle. This new method is validated by comparing with actual production data from the field and the results of a numerical simulation. Also, the effects of related parameters on transient productivity are analyzed. The results show that increasing fracture length, pressure difference and reservoir permeability correspond to an increasing productivity. The research provides theoretical support for the development and optimization of fractured five-spot patterns at the high water cut stage.

scholarly journals Analytical Solution and Simulation of Oil Deliverability Analysis for Reorientation Hydraulic Fracture in Low-Permeability Reservoirs

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-11
Author(s):  
Xinyu Qiu ◽  
Botao Kang ◽  
Pengcheng Liu ◽  
Shengye Hao ◽  
Yanglei Zhou ◽  
...  
Keyword(s):  
Analytical Solution ◽  
Principal Stress ◽  
High Water ◽  
Maximum Principal Stress ◽  
Low Permeability ◽  
Minimum Principal Stress ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut ◽  
Low Permeability Reservoirs

The hydraulic refracturing operations are often used to improve oil deliverability in the low-permeability reservoir. When the development of oilfields has entered a high water cut stage, oil deliverability can be promoted by refracturing reservoirs. The orientation of the new fracture formed by refracturing will be changed. The new formed fracture is called reorientation fracture. To calculate the oil deliverability of the refracture wells, a three-section fracture which includes reorientation fracture was established. The multiwell pressure drop superposition theory is used to derive the analytical solution of the refracture wells which includes the reorientation fracture. The numerical simulation was conducted to validate the results of the analytical solution. Comparing the refracture well deliverability of reorientation and nonreorientation, permeability, deflection angle, and the length of reorientation fracture will jointly control the productivity of refracture well. When the permeability in the direction of maximum principal stress is greater than the permeability in the direction of minimum principal stress, the capacity of reorientation fractures is relatively large. The deflection angles and the length of the reorientation fracture will directly affect the drainage area of the fracture, thus affecting productivity. The reorientation fractures generated by repeated fracturing have great potential for improving oil deliverability in the anisotropic low-permeability reservoirs.

scholarly journals Study on three phase foam for Enhanced Oil Recovery in extra-low permeability reservoirs

2018 ◽  
Vol 73 ◽  
pp. 55 ◽  
Author(s):  
Ming Zhou ◽  
Juncheng Bu ◽  
Jie Wang ◽  
Xiao Guo ◽  
Jie Huang ◽  
...  
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Foam Stability ◽  
Temperature Tolerance ◽  
Resistance Coefficient ◽  
Low Permeability ◽  
Displacement Efficiency ◽  
Three Phase ◽  
Profile Control ◽  
Low Permeability Reservoirs

Poly (MSt-MMA) nanosphere as foam stabilizing agent was synthesized by emulsion polymerization. The three phase foam was prepared with Disodium 4-Dodecyl-2,4′-Oxydiben Zenesulfonate (DOZS) as foaming agent, Hydrolyzed Polyacrylamide (HPAM) and synthesized poly (MSt-MMA) nanospheres as the mixed foam stabilizing agents. It had outstanding foaming performance and foam stability. The optimal three phase foam system consisting of 0.12 wt% HPAM, 0.04 wt% poly (MSt-MMA) nanospheres and 0.12 wt% DOZS by orthogonal experiment, had high apparent viscosity, which showed that three components had a very good synergistic effect. The three phase foam’s temperature tolerance and salt tolerance were researched in laboratory tests. Flooding oil experiment showed that the average displacement efficiency of three phase foam system was 16.1 wt% in single core experiments and 21.7 wt% in double core experiments. Resistance coefficient of low permeability core was more than those of high permeability core, but their residual resistance coefficients were small. The results of core experiment and pilot test indicated that the three phase foam had good profile control ability and generated low damage to the low permeability layer for extra-low permeability reservoirs. Three phase foam flooding has great prospects for Enhanced Oil Recovery (EOR) in extra-low permeability reservoirs.

scholarly journals Techniques for improving the water-flooding of oil fields during the high water-cut stage

2019 ◽  
Vol 74 ◽  
pp. 69 ◽  
Author(s):  
Kuiqian Ma ◽  
Ao Li ◽  
Shuhao Guo ◽  
Jieqiong Pang ◽  
Yongchao Xue ◽  
...  
Keyword(s):  
Oil Recovery ◽  
Water Injection ◽  
Reduction Rate ◽  
High Water ◽  
Water Flooding ◽  
Variable Intensity ◽  
Remaining Oil ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

The multi-layer co-exploitation method is often used in offshore oilfields because of the large spacing between the injection and production wells. As oilfields gradually enter the high water-cut stage, the contradiction between the horizontal and vertical directions becomes more prominent, and the distribution of the remaining oil is more complex. Oilfields are facing unprecedented challenges in further enhancing oil recovery. Using oilfield A, which is in the high water-cut stage, as the research object, we compiled a detailed description of the remaining oil during the high water-cut stage using the information collected during the comprehensive adjustment and infilling of the oilfield. In addition various techniques for tapping the potential reservoir, stabilizing the oil, and controlling the water were investigated. A set of key techniques for the continuous improvement of the efficiency of water injection after comprehensive adjustment of high water-cut fields was generated. Based on the determined configuration of the offshore deltaic reservoir, a set of detailed descriptive methods and tapping technology for extracting the remaining oil in the offshore high water-cut oilfield after comprehensive adjustment was established. By considering the equilibrium displacement and using a new quantitative characterization method that includes displacement, a new technique for determining the quantity of water that needs to be injected into a stratified injection well during the high water-cut stage was established. Based on the principle of flow field intensity reconfiguration, a linear, variable-intensity, alternating injection and withdrawal technique was proposed. With the application of this series of techniques, the increase in the water content was controlled to within 1%, the natural reduction rate was controlled to within 9%, and the production increased by 1.060 × 107 m3.

On the Feasibility of Applying Electric Field to Increase Oil Recovery in Old Oil Field

2014 ◽  
Vol 900 ◽  
pp. 677-680
Author(s):  
Chun Hong Nie
Keyword(s):  
Electric Field ◽  
Oil Recovery ◽  
Water Injection ◽  
High Water ◽  
Oil Field ◽  
Thin Layers ◽  
Stable Yield ◽  
High Water Cut Stage ◽  
High Water Cut ◽  
Water Cut

This paper has discussed the characteristics, roles, feasibility and obvious effects of the technology by applying electric field to enhance oil recovery when the oil field is in high water cut stage and super high water cut stage. In view that most oil wells in old oil field have entered into the super high water cut production, the remaining oil in the main reservoir is in fragmented distribution with poor results of water injection and new reserves of oil mostly have a low penetration rate and are thin layers of poor physical properties, the use of the direct current field in period of high water cut is the best policy to achieve high and stable yield and is fairly promising.

scholarly journals Effect of Emulsification on Enhanced Oil Recovery during Surfactant/Polymer Flooding in the Homogeneous and Heterogeneous Porous Media

Geofluids ◽  
2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiaoyan Wang ◽  
Jie Zhang ◽  
Guangyu Yuan ◽  
Wei Wang ◽  
Yanbin Liang ◽  
...  
Keyword(s):  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
High Water ◽  
Heterogeneous Porous Media ◽  
Recovery Factor ◽  
Water Flooding ◽  
Core Flooding ◽  
Positive Role ◽  
High Water Cut ◽  
Water Cut

Surfactant polymer (SP) flooding has become an important enhanced oil recovery (EOR) technique for the high-water cut mature oilfield. Emulsification in the SP flooding process is regarded as a powerful mark for the successful application of SP flooding in the filed scale. People believe emulsification plays a positive role in EOR. This paper uses one-dimensional homogenous core flooding experiments and parallel core flooding experiments to examine the effect of emulsification on the oil recoveries in the SP flooding process. 0.3 pore volume (PV) of emulsions which are prepared using ultralow interface intension (IFT) SP solution and crude oil with stirring method was injected into core models to mimic the emulsification process in SP flooding, followed by 0.35 PV of SP flooding to flood emulsions and remaining oil. The other experiment was preformed 0.65 PV of SP flooding as a contrast. We found SP flooding can obviously enhance oil recovery factor by 25% after water flooding in both homogeneous and heterogeneous cores. Compared to SP flooding, emulsification can contribute an additional recovery factor of 3.8% in parallel core flooding experiments. But there is no difference on recoveries in homogenous core flooding experiments. It indicates that the role of emulsification during SP flooding will be more significant for oil recoveries in a heterogeneous reservoir rather than a homogeneous reservoir.

scholarly journals Screening and assessing the conditions for effective oil recovery enhancing techniques application for hard to recover high-water cut reserves

2021 ◽  
pp. 48-56
Author(s):  
V. V. Mukhametshin ◽  
◽  
R. N. Bakhtizin ◽  
L. S. Kuleshova ◽  
A. P. Stabinskas ◽  
...  
Keyword(s):  
Numerical Modeling ◽  
Enhanced Oil Recovery ◽  
Oil Recovery ◽  
Oil And Gas ◽  
Chemical Properties ◽  
High Water ◽  
Recovery Techniques ◽  
High Water Cut ◽  
Water Cut ◽  
Criterion Analysis

For the conditions of deposits in Jurassic and Paleozoic terrigenous reservoirs of the Sherkalinsky trough and Shaimsky swell of Western Siberia, a criterion analysis and screening of enhanced oil recovery techniques used in the fields of the West Siberian oil and gas province were carried out. For various groups of oil fields, a set of the most effective technologies for the development of residual hard-to-recover reserves of flooded fields has been proposed. The areas for effective application of the selected techniques for deposits introduced into development within the considered tectonic-stratigraphic elements are determined. The areas determination was carried out on the basis of 19 parameters characterizing the geological-physical and physical-chemical properties of formations and fluids, as well as the maximum and minimum values of the canonical discriminant functions determined by the situational map. Based on the numerical modeling of oil recovery processes, a forecast of an increase in the final oil recovery factor was made for five facilities-field test sites of the selected groups of facilities. Keywords: hard-to-recover reserves; terrigenous reservoirs; factor analysis; enhanced oil recovery techniques; numerical modeling; criterion analysis.

Sign in / Sign up

Export Citation Format

Share Document