scholarly journals Stress-Strain Relationship of Steel Fiber Reinforced Alkali Activated Slag Concrete under Static Compression

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Xiaohui Yuan ◽  
Huiting Guan ◽  
Yanyu Shi
Keyword(s):  
Damage Evolution ◽  
Steel Fiber ◽  
Strain Curve ◽  
Fiber Reinforced ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Alkali Activated Slag ◽  
Strain Relationship ◽  
Activated Slag ◽  
Alkali Activated

Stress-strain curve can accurately reflect the mechanical behavior of materials, and it is very important for structural design and nonlinear numerical analysis. Some cube and prism specimens were made to investigate the physical and mechanical properties of steel fiber reinforced alkali activated slag concrete (AASC); test results show that the strength, Young’s Elastic Modulus, and Poisson’s ratio all increase with the increase of steel fiber content. The steel fiber reinforced AASC shows an excellent postcracking behavior. Damage evolution parameter (D) was used to describe the formation and propagation of cracks, and continuum damage evolution model of steel fiber reinforced AASC was established by Weibull and Cauchy distribution. The establishing model can well describe the geometric characteristics of the key points of the concrete materials stress-strain curve. Finally, the accuracy of the model was verified by comparing the test stress-strain relationship curve of steel fiber reinforced AASC.

Research on the Stress-Strain Curve and Damage of Steel Fiber Reinforced Concrete under Uniaxial Loading

2011 ◽  
Vol 255-260 ◽  
pp. 383-388
Author(s):  
Run Nian Yang ◽  
De Min Wei
Keyword(s):  
Reinforced Concrete ◽  
Fatigue Failure ◽  
Steel Fiber ◽  
Strain Curve ◽  
Fiber Reinforced Concrete ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Static Failure

The static failure can be seen as a special fatigue failure, which means the static failure is the fatigue failure only bearing one cycle under the ultimate-strength loading. By learning from the analysis of fatigue damage, the stress- strain curve and damage of steel fiber reinforced concrete under uniaxial loading have been studied in this paper. The damage evolution equation can be derived from the damage theory, and it can be used to describe the relationship between the damage variable and strain. According to the strain equivalence principle, the corresponding constitutive equation considering damage can be obtained. Finally, comparisons among test results, the model and ansys simulation results show that the model is suitable to describe the uniaxial stress-strain curves of steel fiber reinforced concrete.

scholarly journals Mechanical Properties and Eco-Efficiency of Steel Fiber Reinforced Alkali-Activated Slag Concrete

Materials ◽  
2015 ◽  
Vol 8 (11) ◽  
pp. 7309-7321 ◽  
Author(s):  
Sun-Woo Kim ◽  
Seok-Joon Jang ◽  
Dae-Hyun Kang ◽  
Kyung-Lim Ahn ◽  
Hyun-Do Yun
Keyword(s):  
Mechanical Properties ◽  
Steel Fiber ◽  
Fiber Reinforced ◽  
Alkali Activated Slag ◽  
Activated Slag ◽  
Alkali Activated

Behavior and modeling of post-heated circular concrete specimens repaired with fiber-reinforced polymer composites

2021 ◽  
pp. 136943322110585
Author(s):  
Seyed Mehrdad Elhamnike ◽  
Rasoul Abbaszadeh ◽  
Vahid Razavinasab ◽  
Hadi Ziaadiny
Keyword(s):  
Strain Curve ◽  
Concrete Columns ◽  
Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Concrete Members ◽  
Frp Composites ◽  
Reinforced Polymer ◽  
Fiber Reinforced Polymer Composites

Exposure of buildings to fire is one of the unexpected events during the life of the structure. The heat from the fire can reduce the strength of structural members, and these damaged members need to be strengthened. Repair and strengthening of concrete members by fiber-reinforced polymer (FRP) composites has been one of the most popular methods in recent years and can be used in fire-damaged concrete members. In this paper, in order to provide further data and information about the behavior of post-heated circular concrete columns confined with FRP composites, 30 cylindrical concrete specimens were prepared and subjected under four exposure temperatures of 300, 500, 700, and 900. Then, specimens were repaired by carbon fiber reinforced polymer composites and tested under axial compression. Results indicate that heating causes the color change, cracks, and weight loss of concrete. Also, with the increase of heating temperature, the shape of stress–strain curve of FRP-retrofitted specimens will change. Therefore, the main parts of the stress–strain curve such as ultimate stress and strain and the elastic modulus will change. Thus, a new stress–strain model is proposed for post-heated circular concrete columns confined by FRP composites. Results indicate that the proposed model is in a good agreement with the experimental data.

Fracture Assessment of Pipes Having Multiple Flaws Based on Ramberg–Osgood-Type Stress–Strain Relationships

2011 ◽  
Author(s):  
Hideo Machida ◽  
Tetsuya Hamanaka ◽  
Yoshiaki Takahashi ◽  
Katsumasa Miyazaki ◽  
Fuminori Iwamatsu ◽  
...  
Keyword(s):  
Flow Stress ◽  
Stress Concentration ◽  
Fracture Strength ◽  
Strain Curve ◽  
Assessment Method ◽  
Experimental Results ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Strain Relationship ◽  
Fracture Assessment

This paper describes a fracture assessment method for a pipe having multiple circumferential flaws. According to Fitness-for-Service (FFS) codes for nuclear facilities published by the Japanese Society of Mechanical Engineers (JSME), the fracture strength of a high-ductility pipe having a circumferential flaw is evaluated using the limit load assessment method assuming the elastic–perfectly-plastic stress–strain relationship. In this assessment, flow stress is used as a proportional stress. However, previous experimental results [1, 2, 3] show that a crack penetrates before the entire flawed pipe section reaches the flow stress. Therefore, stress concentration at a flaw was evaluated on the basis of the Dugdale model [4], and the fracture strength of the crack-ligament was evaluated. This model can predict test results with high accuracy when the ligament fracture strength is assumed to be tensile strength. Based on this examination, a fracture assessment method for pipes having multiple flaws was developed considering the stress concentration in the crack-ligament by using the realistic stress–strain relationship (Ramberg–Osgood-type stress–strain curve). The fracture strength of a multiple-flawed pipe estimated by the developed method was compared with previous experimental results. When the stress concentration in the crack-ligament was taken into consideration, the fracture strength estimated using the Ramberg–Osgood-type stress–strain curve was in good agreement with experimental results, confirming the validity of the proposed method.

scholarly journals Impacts of Casting Scales and Harsh Conditions on the Thermal, Acoustic, and Mechanical Properties of Indoor Acoustic Panels Made with Fiber-Reinforced Alkali-Activated Slag Foam Concretes

Materials ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 825 ◽  
Author(s):  
Mastali Mohammad ◽  
Kinnunen Paivo ◽  
Karhu Marjaana ◽  
Abdollahnejad Zahra ◽  
Korat Lidija ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Comparative Study ◽  
Sound Absorption ◽  
Acoustic Properties ◽  
Recycled Aggregates ◽  
Fiber Reinforced ◽  
Alkali Activated Slag ◽  
Activated Slag ◽  
Harsh Conditions ◽  
Alkali Activated

This paper presents experimental results regarding the efficiency of using acoustic panels made with fiber-reinforced alkali-activated slag foam concrete containing lightweight recycled aggregates produced by using Petrit-T (tunnel kiln slag). In the first stage, 72 acoustic panels with dimension 500 × 500 × 35 mm were cast and prepared. The mechanical properties of the panels were then assessed in terms of their compressive and flexural strengths. Moreover, the durability properties of acoustic panels were studied using harsh conditions (freeze/thaw and carbonation tests). The efficiency of the lightweight panels was also assessed in terms of thermal properties. In the second stage, 50 acoustic panels were used to cover the floor area in a reverberation room. The acoustic absorption in diffuse field conditions was measured, and the interrupted random noise source method was used to record the sound pressure decay rate over time. Moreover, the acoustic properties of the panels were separately assessed by impedance tubes and airflow resistivity measurements. The recorded results from these two sound absorption evaluations were compared. Additionally, a comparative study was presented on the results of impedance tube measurements to compare the influence of casting volumes (large and small scales) on the sound absorption of the acoustic panels. In the last stage, a comparative study was implemented to clarify the effects of harsh conditions on the sound absorption of the acoustic panels. The results showed that casting scale had great impacts on the mechanical and physical properties. Additionally, it was revealed that harsh conditions improved the sound properties of acoustic panels due to their effects on the porous structure of materials.

Experimental Study of Stress-Strain Curves of Lightweight Aggregate Concrete

2010 ◽  
Vol 163-167 ◽  
pp. 1762-1767 ◽  
Author(s):  
Xiang Liu ◽  
Jiang Tao Kong
Keyword(s):  
Strain Curve ◽  
Lightweight Aggregate ◽  
Lightweight Aggregate Concrete ◽  
Stress Strain Curve ◽  
Stress Strain ◽  
Concrete Material ◽  
Aggregate Concrete ◽  
Ordinary Concrete ◽  
Strength Grade ◽  
Strain Relationship

According to the contrast test of LC30, LC40 lightweight aggregate concrete and C30, C40 common concrete , the text researched the mechanical property of lightweight aggregate concrete and ordinary concrete in the same strength grade and obtained the regularity of stress-strain curve of lightweight aggregate concrete in different strength grade. Then we contrasted the experimental results and planning model, analysed the difference, and suggested that the standards should improve the descent stage of the stress-strain curve of lightweight aggregate concrete combined with correlative experiments data, and give the equation of the descent stage of stress-strain curves. Concrete material in axial compression is the basic physical mechanical performance of concrete material, and is the main basis for researching bearing capacity and deformation of concrete construction. The stress-strain relationship is all-around macroscopic reaction of basal compressive property . There have been many experiments work about the stress-strain relationship of lightweight aggregate concrete at home and abroad , and found the peak strain of lightweight aggregate concrete is higher than that of ordinary concrete in the context of same peak stress .In this paper, on the basis of experimental investigations of lightweight aggregate concrete , aim at the stress-strain relationship ,we have take comparison experiment about LC30,LC40 lightweight aggregate concrete and C30,C40 ordinary concrete , and sort out stress-strain curve under the condition of the shaft center being compressed, so get the average tress-strain curve of LC30,LC40 lightweight aggregate concrete , and analyse the curve.

Sign in / Sign up

Export Citation Format

Share Document