Development and Characterization of Acrylic Based Bone Cements

2022 ◽  
Vol 12 (3) ◽  
pp. 471-479
Author(s):  
Aqsa Khan ◽  
Ghazna Hassan Khan ◽  
Eraj Humayun Mirza ◽  
Alidad Chandio ◽  
Maliha Mohsin ◽  
...  
Keyword(s):  
Bone Cement ◽  
Morphological Changes ◽  
Chemical Properties ◽  
Bone Cements ◽  
Mechanical And Thermal Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Physical And Chemical ◽  
And Chemical Properties

Bone tissue engineering has emerged as a multidisciplinary field in recent times with an aim to expedite the process of regeneration of damaged or diseased tissues. This study is an attempt to fabricate and characterize Tricalcium Phosphate (TCP) and Chitosan incorporated Polymethylmethacrylate (PMMA) based bone cement. In total two experimental PMMA based bone cements were fabricated that were differentiated by presence and absence of Chitosan. In both groups (10 and 30 wt.%) TCP were incorporated into Methyl methacrylate (MMA) monomer. PMMA was used as a control. The physical, mechanical and thermal properties of the composites were assessed. Morphological changes of PMMA after the introduction of TCP and Chitosan were observed by means of X-ray diffraction (XRD). Major peak shifts in Fourier transform Infrared spectroscopy (FTIR) spectra demonstrated the strong bonding of PMMA with incorporated materials. PMMA incorporated with 10% TCP showed the maximum wettability in absence of Chitosan. Hardness of the tested specimens decreased with increasing content of TCP which in turns enhanced ductility. It was also observed that neither of the samples showed significant degradation. The incorporation of additives enhance the physical and chemical properties of PMMA as bone cement.

Characterization of Shivirtui Zeolite Modified with Aluminum Oxyhydroxide Nanofibers

2019 ◽  
Vol 942 ◽  
pp. 40-49
Author(s):  
Yulia Murashkina ◽  
Olga B. Nazarenko
Keyword(s):  
Chemical Properties ◽  
Nitrogen Adsorption ◽  
X Ray Diffraction ◽  
Scanning Electronic Microscopy ◽  
Electronic Microscopy ◽  
X Ray ◽  
Physical And Chemical ◽  
And Chemical Properties ◽  
Aluminum Oxyhydroxide

Natural zeolite of Shivirtui deposit (Russia) was modified with nanofibers of aluminum oxyhydroxide AlOOH. Aluminum oxyhydroxide nanofibers were produced at the heating and oxidation of aluminum powder with water. The properties of modified zeolite were investigated by means of X-ray diffraction, transmission electronic microscopy, scanning electronic microscopy, low-temperature nitrogen adsorption, thermal analysis, and Fourier transform infrared spectroscopy. It was found that water content in the modified sample of zeolite was about 15 %. Based on the study of the physical and chemical properties, shivirtui zeolite modified with nanofibers of aluminum oxyhydroxide can be proposed for use as a flame-retardant additive to polymers.

Physical and Chemical Properties of Mineral in Soils of Cassava Cropping Area: A Case Study in Chonburi Province

2014 ◽  
Vol 979 ◽  
pp. 440-443
Author(s):  
W. Siriprom ◽  
K. Teanchai ◽  
S. Kongsriprapan ◽  
J. Kaewkhao ◽  
N. Sangwaranatee
Keyword(s):  
Thermo Gravimetric Analysis ◽  
Chemical Properties ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Xrd Pattern ◽  
X Ray ◽  
Physical And Chemical ◽  
And Chemical Properties

The chemical and physical properties of topsoil and subsoil which collected from the cassava cropping area in Chonburi Province have been investigated. The characterization of both soil sample were used X-Ray Diffraction (XRD), Energy Dispersive X-Ray Fluorescence (EDXRF) while FTIR used to confirmed the formation of intermolecular bonding and Thermo-Gravimetric Analysis (TGA) used for investigated the crystalline. It was found that, the XRD pattern indicated quartz phase. The chemical composition by XRF reported that the soils samples consist of Si, Al, Ca, Fe, K, Mn, Ti, Cr, Zn, Ag and Cu. and TGA results, noticed that the removal of moisture and organics material.

Synthesis and characterization of a composite organic semiconductor (curcumin-paracetamol/TiO2)

2020 ◽  
pp. 096739112092169
Author(s):  
Asmaa Bouazza ◽  
Salah Bassaid ◽  
Bouabdallah Daho ◽  
Massimo Messori ◽  
Abdelkader Dehbi
Keyword(s):  
Organic Semiconductor ◽  
Chemical Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Production Water ◽  
Synthesis Methodology ◽  
Physical And Chemical ◽  
Electronic And Structural Properties ◽  
And Chemical Properties

The aim of this work is to study some physical and chemical properties of an organic semiconductor (OSc)/ x%titanium dioxide (TiO2) heterosystem (with 0 ≤ x ≤ 20%) (OScs/ x%TiO2). The OSc is obtained from pure curcumin and paracetamol as starting molecules. The synthesis methodology of the mixtures of OScs/ x%TiO2 heterosystem involves a microwave-assisted multicomponent reaction using curcumin, paracetamol, and TiO2 as a heterogeneous solution. All mixtures were analyzed by Fourier-transform infrared spectroscopy, Raman spectroscopy, thermogravimetric analysis/differential thermal analysis, X-ray diffraction, ultraviolet–visible spectroscopy, and scanning electron microscopy. The results obtained show a new nanocomposite with interesting pharmaceutical, optical, electronic, and structural properties, which can be used in the fields of energy production, water purification, and air purification, as a biomaterial and for electronic applications.

Preparation of Magnetite-Mg/Al Hydrotalcite through Hydrothermal Process and Subsequent Calcination

2015 ◽  
Vol 1101 ◽  
pp. 336-339 ◽  
Author(s):  
Triastuti Sulistyaningsih ◽  
Sri Juari Santosa ◽  
Dwi Siswanta ◽  
Bambang Rusdiarso
Keyword(s):  
Hydrothermal Process ◽  
Chemical Properties ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Subsequent Calcination ◽  
The Fourier Transform ◽  
Physical And Chemical ◽  
And Chemical Properties

Fe3O4/Mg-Al-NO3-hydrotalcite composite compounds have been synthesized by hydrothermal process followed by calcination to learn the differences in physical and chemical properties of each compound. Hydrothermal was performed at a temperature of 120 °C for 5 h and calcinations was at 450 °C for 3 hours. Characterization of the composite compounds was conducted using the Fourier Transform Infrared Spectroscopy (FTIR), the X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET) and Vibrating Sample Magnetometer (VSM). The characterization results showed that crystallinity, surface area and magnetic properties of hydrothermally treated Mg/Al hydrotalcite-magnetite were higher than those unhydrothermal and calcination products.

Synthesis and Characterization of Zn doped Li(Li0.21Mn0.54Ni0.125Co0.125)O2 as the Layer Materials For Battery Applications

2018 ◽  
Vol 21 (2) ◽  
pp. 127-131
Author(s):  
S. Rumh. Kadhim ◽  
Reihan Etefagh ◽  
H. Arabi
Keyword(s):  
Infrared Spectroscopy ◽  
Chemical Elements ◽  
Sol Gel ◽  
Chemical Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Physical And Chemical ◽  
And Chemical Properties

In this paper, pure and impure nanopowders of Li(Li0.021Mn0.54Ni0.125Co0.125)O2 were prepared with different percentages (x=0.02%, 0.05%, 0.075%, 0.10%) of Zn impurity by sol-gel method, and the effect of different percentages were investigated on the structural, physical and chemical properties of the samples. These properties of samples characterized by X-ray diffraction (XRD), field-scattering microscopy (FESEM), X-ray energy spectroscopy (EDS), transmission electron microscopy (TEM), thermogravimetric analysis (TGA), differential thermal analysis (DTA), infrared spectroscopy (FTIR), and the results of characterization were investigation. All the reflection peaks indicate that the samples have standard α-NaFeO2 layered structure with the space group R3m, except for the super lattice ordering between 22°-25°.The FESEM images have shown that these nanoparticles have Hexagonal structures for doped and undoped nanopowders. The particle size of nanopowders in the range of 30-80 nm the chemical analysis of EDS has proven the presence of Zn in the samples. TG /DTA measurements showed weight loss in pure and impure of nanopowders. In infrared spectroscopy (FTIR), the connection bonds and chemical elements used in these nanopowders have been investigated.

Monitoring of Fluctuations in the Physical and Chemical Properties of a High-Calcium Fly Ash

1987 ◽  
Vol 113 ◽  
Author(s):  
Scott Schlorholtz ◽  
Ken Bergeson ◽  
Turgut Demirel
Keyword(s):  
Fly Ash ◽  
Chemical Properties ◽  
Operating Conditions ◽  
Physical And Chemical Properties ◽  
X Ray Diffraction ◽  
X Ray ◽  
Morphological Studies ◽  
High Calcium ◽  
Physical And Chemical ◽  
And Chemical Properties

ABSTRACTThe physical and chemical properties of fly ash produced at Ottumwa Generating Station have been monitored since April, 1985. The fly ash is produced from burning a low sulfur, sub-bituminous coal obtained from the Powder River Basin near Gillette, Wyoming. One-hundred and sixty samples of fly ash were obtained during the two year period. All of the samples were subjected to physical testing as specified by ASTM C 311. About one-hundred of the samples were also subjected to a series of tests designed to monitor the self-cementing properties of the fly ash. Many of the fly ash samples were subjected to x-ray diffraction and fluorescence analysis to define the mineralogical and chemical composition of the bulk fly ash as a function of sampling date. Hydration products in selected hardened fly ash pastes, were studied by x-ray diffraction and scanning electron microscopy. The studies indicated that power plant operating conditions influenced the compressive strength of the fly ash paste specimens. Mineralogical and morphological studies of the fly ash pastes indicated that stratlingite formation occurred in the highstrength specimens, while ettringite was the major hydration product evident in the low-strength specimens.

Bioceramic Production from Giant Purple Barnacle (Megabalanus tintinnabulum)

2014 ◽  
Vol 631 ◽  
pp. 137-142 ◽  
Author(s):  
F.N. Oktar ◽  
H. Gokce ◽  
O. Gunduz ◽  
Y.M. Sahin ◽  
D. Agaogullari ◽  
...  
Keyword(s):  
Chemical Properties ◽  
Complete Characterization ◽  
Molar Ratio ◽  
X Ray Diffraction ◽  
Hot Plate ◽  
X Ray ◽  
Fine Powders ◽  
Simple Economic ◽  
And Chemical Properties

In this study the structural and chemical properties of barnacle shell based bioceramic materials (i.e. hydroxyapatite, whitlockite, monetite and other phases) were produced by using mechano-chemical (hot-plate) conversion method. Cleaned barnacle shells were ball milled down to <75µm in diameter. Differential thermal and gravimetric analyses (DTA/TGA) were performed to determine the exact CaCO3 content. Sample batches of 2g were prepared from the fine powders produced. For each batch, the required volume of an aqueous H3PO4 solution was calculated in order to set the stoichiometric molar ratio of Ca/P equal to 1.5 for ß-tricalcium phosphate (ß-TCP) or to 1.667 for hydroxyapatite (HA). The temperature was set to 80°C for 15 minutes to complete the process. After the titration of the equivalent amount of H3PO4 into the prepared solution, agitation was carried out on a hot-plate (i.e. mechano-chemical processing) for 8 hours. The sediments formed were dried and the resulting TCP and HA powders were calcined at 400°C and 800°C respectively. For complete characterization of the bioceramics produced, scanning electron microscopy (SEM), fourier transform infrared spectroscopy (FTIR) and x-ray diffraction (XRD) analyses were carried out. The current study proposes a simple, economic and time efficient method for nano-bioceramic production.

Preparation and Evaluation of Nano-Hydroxyapatite/β-Tricalcium Phosphate/Chitosan Composite Scaffolds for Bone Tissue Engineering

2007 ◽  
Vol 361-363 ◽  
pp. 463-466
Author(s):  
T. Lin ◽  
S.M. Zhang ◽  
J. Li ◽  
L. Zhang ◽  
Y.H. Liu ◽  
...  
Keyword(s):  
Chemical Properties ◽  
Physical And Chemical Properties ◽  
X Ray Diffraction ◽  
Composite Scaffolds ◽  
X Ray ◽  
Viable Cells ◽  
Physical And Chemical ◽  
Chitosan Composite ◽  
Preparation And Evaluation ◽  
And Chemical Properties

The composite scaffolds with nine different ratios of nano-HA and ß-TCP content were fabricated by using lyophilization method. Their microscopy, physical and chemical properties were investigated by using scanning electron microscopy (SEM), X-ray diffraction (XRD), and fourier transformed infrared (FTIR) spectroscopy. MTT test was applied to quantitatively assess the number of viable cells attached and grown on the scaffolds. And the result showed that the amount of cells on the scaffold containing 30% by mass of nano-HA was significantly higher than the other samples.

scholarly journals Change of physical and chemical properties clinoptilolite after mechanical activation

2015 ◽  
Vol 11 (2) ◽  
pp. 58-61
Author(s):  
Anastasiya G Bebiya ◽  
Pavel Y Gulyaev ◽  
Irina V Milyukova
Keyword(s):  
Mechanical Activation ◽  
Chemical Properties ◽  
Optimal Time ◽  
X Ray Diffraction ◽  
X Ray ◽  
Sorption Ability ◽  
Maximum Sorption ◽  
Activation Times ◽  
Physical And Chemical ◽  
And Chemical Properties

Presents experimental data depending on the specific surface area and sorption properties of the clinoptilolite powder mechanical activation times. Carried out X-ray diffraction and spec-troscopic analysis of mechanically activated zeolite. Find the optimal time and mechanical activation modes which relate the maximum sorption ability.

Sign in / Sign up

Export Citation Format

Share Document