Effect of Friction Stir Welding Parameters on Microstructure and Properties of Welded 5083 Aluminium Alloy

2020 ◽  
Vol 20 (8) ◽  
pp. 5055-5063
Author(s):  
Lixin Hao ◽  
Ruiling Jia ◽  
Xiwei Zhai ◽  
Huixia Zhang ◽  
Jian Hou
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Heat Affected Zone ◽  
Intermetallic Phase ◽  
Welding Parameters ◽  
Kelvin Probe ◽  
Friction Stir ◽  
The Difference ◽  
Fsw Parameters

The friction stir welding (FSW) parameters were designed in this study by orthogonal experimental method. The microstructure, mechanical properties and corrosion behavior of corresponding FSW joints of 5083 aluminium alloy (AA5083) were also investigated. Scanning Kelvin probe force microscopy (SKPFM) was employed to study local potential differences on the FSW joint. Results showed that the welding parameters greatly influenced the FSW joint properties of the AA5083. The ratio of rotation speed to welding speed (n/v) mainly affected the mechanical properties of the joint. The tensile strength for the joint was reduced when welded with too large or too small n/v. The hardness of all FSW joints was characterized with similar ‘W-shaped,’ and minimum hardness value appeared on advancing side of the heat affected zone. Different heat input and agitation intensity caused heterogeneous microstructure for the AA5083 FSW joint, which led to differences in passivation properties of weld nugget zone, thermo-mechanically affected zone and heat-affected zone. Susceptibility of the AA5083 FSW joint to pitting corrosion was attributed to the difference of relative potential between the intermetallic phase and Al matrix.

scholarly journals Research on the Friction Stir Welding of Sc-Modified AA2519 Extrusion

Metals ◽  
2019 ◽  
Vol 9 (10) ◽  
pp. 1024 ◽  
Author(s):  
Robert Kosturek ◽  
Lucjan Śnieżek ◽  
Janusz Torzewski ◽  
Marcin Wachowski
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Base Material ◽  
Stir Zone ◽  
Welding Parameters ◽  
Friction Stir ◽  
Treated Condition ◽  
Heat Treated ◽  
Heat Treated Condition ◽  
Fsw Parameters

The aim of this research was to investigate the effect of friction stir welding (FSW) parameters on microstructure and mechanical properties of Sc-modified AA2519 extrusion joints. The workpiece was welded by FSW in non-heat-treated condition with seven different sets of welding parameters. For each obtained joint macrostructure and microstructure observations were performed. Mechanical properties of joints were investigated using tensile test together with localization of fracture location. Joint efficiencies were established by comparing measured joints tensile strength to the value for base material. The obtained results show that investigated FSW joints of Sc-modified AA2519 in the non-heat-treated condition have joint efficiency within the range 87–95%. In the joints obtained with the lowest ratio of the tool rotation speed to the tool traverse speed, the occurrence of imperfections (voids) localized in the stir zone was reported. Three selected samples were subjected to further investigations consisting microhardness distribution and scanning electron microscopy fractography analysis. As the result of dynamic recrystallization, the microhardness of the base material value of 86 HV0.1 increased to about 110–125 HV0.1 in the stir zone depending on the used welding parameters. Due to lack of the strengthening phase and low strain hardening of used alloy the lack of a significantly softened zone was reported by both microhardness analysis and investigation of the fractured samples.

scholarly journals The Influence of Tool Shape and Process Parameters on the Mechanical Properties of AW-3004 Aluminium Alloy Friction Stir Welded Joints

Materials ◽  
2021 ◽  
Vol 14 (12) ◽  
pp. 3244
Author(s):  
Anna Janeczek ◽  
Jacek Tomków ◽  
Dariusz Fydrych
Keyword(s):  
Mechanical Properties ◽  
Aluminium Alloy ◽  
Welding Speed ◽  
Welded Joints ◽  
Rotational Speed ◽  
Welding Parameters ◽  
Friction Stir ◽  
Tool Shape ◽  
Joint Quality ◽  
Fsw Parameters

The purpose of the following study was to compare the effect of the shape of a tool on the joint and to obtain the values of Friction Stir Welding (FSW) parameters that provide the best possible joint quality. The material used was an aluminium alloy, EN AW-3004 (AlMn1Mg1). To the authors’ best knowledge, no investigations of this alloy during FSW have been presented earlier. Five butt joints were made with a self-developed, cylindrical, and tapered threaded tool with a rotational speed of 475 rpm. In order to compare the welding parameters, two more joints with a rotational speed of 475 rpm and seven joints with a welding speed of 300 mm/min with the use of a cylindrical threaded pin were performed. This involved a visual inspection as well as a tensile strength test of the welded joints. It was observed that the value of the material outflow for the joints made with the cylindrical threaded pin was higher than it was for the joints made with the tapered threaded pin. However, welding defects in the form of voids appeared in the joints made with the tapered threaded tool. The use of the cylindrical tool resulted in higher values for about 37% of mechanical properties compared with the highest result for the tapered threaded joint. As far as the parameters were concerned, it was concluded that most of the specimens were properly joined for a rotational speed of 475 rpm. In the joints made with a welding speed of 300 mm/min, the material was not stirred properly. The best joint quality was given for a rotational speed of 475 rpm as well as a variety of welding speed values between 150 and 475 mm/min.

Microstructure and Mechanical Properties at the Unsteady Areas of Non-Linear Friction Stir Welding

2007 ◽  
Vol 561-565 ◽  
pp. 1059-1062 ◽  
Author(s):  
H. Takahara ◽  
Masato Tsujikawa ◽  
Sung Wook Chung ◽  
Y. Okawa ◽  
Kenji Higashi
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Welding Parameter ◽  
Butt Joints ◽  
Friction Stir ◽  
Non Linear ◽  
Linear Friction ◽  
Fsw Parameters ◽  
Five Axis ◽  
Welding Direction

The influence of tool control in non-linear friction stir welding (FSW) on mechanical properties of joints was investigated. FSW is widely applied to linear joints. It is impossible for five axis FSW machines, however, to keep all the FSW parameters in optimum conditions at non-linear welding. Non-linear FSW joints should be made by compromise with the order of priority for FSW parameters. The tensile test results of butt joints with rectangular change in welding direction on plate plane (L-shaped butt joints) with various welding parameter change. It was found that turn to the retreating side is encouraged when welding direction change. And the method of zero inclination tool angle is effective at non-linear and plane welding.

scholarly journals Thermo-mechanical analysis of linear welding stage in friction stir welding - influence of welding parameters

2021 ◽  
pp. 186-186
Author(s):  
Darko Veljic ◽  
Marko Rakin ◽  
Aleksandar Sedmak ◽  
Nenad Radovic ◽  
Bojan Medjo ◽  
...  
Keyword(s):  
Friction Stir Welding ◽  
Heat Generation ◽  
Welding Speed ◽  
Reaction Force ◽  
Material Model ◽  
Element Model ◽  
Welding Parameters ◽  
Al Alloy ◽  
Friction Stir ◽  
Fsw Parameters

The influence of friction stir welding (FSW) parameters on thermo-mechanical behaviour of the material during welding is analysed. An aluminium alloy is considered (Al 2024 T351), and different rotating speed and welding speed are applied. Finite element model consists of the plate (Al alloy), backing plate and welding tool, and it is formed and solved in software package Simulia Abaqus. The influence of the welding conditions on material behaviour is taken into account by application of the Johnson-Cook material model. The rotation of the tool affects the results: if increased, it contributes to an increase of friction-generated heat intensity. The other component of the generated heat, the plastic deformation of the material, is negligibly changed. When the welding speed is increased, the intensity of friction-generated heat decreases, while the heat generation due to plastic deforming increases. Combined, these two effects cause small change of the total heat generation. For the same welded joint length, the plate welded by lower speed will be heated more intensively. The changes of the heat generation influence both the temperature field and reaction force, which are also considered.

Friction Stir Welding of Elements Made of Cast Aluminium Alloys

2014 ◽  
Vol 59 (1) ◽  
pp. 385-392
Author(s):  
B. Rams ◽  
A. Pietras ◽  
K. Mroczka
Keyword(s):  
Friction Stir Welding ◽  
Aluminium Alloy ◽  
Aluminium Alloys ◽  
Welding Parameters ◽  
Process Conditions ◽  
Friction Stir ◽  
Seam Weld ◽  
Cast Aluminium ◽  
Weld Structure ◽  
Welding Stability

Abstract The article presents application of FSW method for joining elements made of cast aluminium alloys which are hardly weldable with other known welding techniques. Research’s results of plasticizing process of aluminium and moulding of seam weld during different FSW process’ conditions were also presented. Influence of welding parameters, shape and dimensions of tool on weld structure, welding stability and quality was examined. Application of FSW method was exemplified on welding of hemispheres for valves made of cast aluminium alloy EN AC-43200.

scholarly journals Friction Stir Welding Parameters: Impact of Abnormal Grain Growth during Post-Weld Heat Treatment on Mechanical Properties of Al–Mg–Si Welded Joints

Metals ◽  
2020 ◽  
Vol 10 (12) ◽  
pp. 1607
Author(s):  
Amir Hossein Baghdadi ◽  
Zainuddin Sajuri ◽  
Mohd Zaidi Omar ◽  
Armin Rajabi
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Friction Stir Welding ◽  
Grain Growth ◽  
Precipitation Hardening ◽  
Al Alloys ◽  
Abnormal Grain Growth ◽  
Post Weld Heat Treatment ◽  
Welding Parameters ◽  
Friction Stir

Friction stir welding (FSW) is an alternative method to join aluminum (Al) alloys in a solid-state condition. However, the coarsening or dissolution of precipitation hardening phases in the welding zone causes strength reduction or softening behavior in the welded area of age-hardened Al alloys. Therefore, this research aimed to improve the mechanical properties of an FSW Al–Mg–Si alloy via post-weld heat treatment (PWHT) and the possibility of controlling the abnormal grain growth (AGG) using different welding parameters. FSW was performed with different rotational and travel speeds, and T6 heat treatment was carried out on the FSW samples as the PWHT. The results showed a decrease in the strength of the FSW samples compared with that of the base material (BM) due to the dissolution of precipitation hardening particles in the heat-affected zone. However, the emergence of AGG in the microstructure after the T6-PWHT was identified as the potential event in the microstructure of the PWHT samples. It is found that the AGG of the microstructure in similar joints of Al6061(T6) was governed by the welding parameters. The results proved that PWHT was able to increase the tensile properties of the welded samples to values comparable to that of Al6061(T6)-BM. The increased mechanical properties of the FSW joints were attributed to a proper PWHT that resulted in a homogeneous distribution of the precipitation hardening phases in the welding zones.

Evaluation of dissimilar joints properties of 5083-H12 and 6061-T6 aluminum alloys produced by tungsten inert gas and friction stir welding

2015 ◽  
Vol 231 (3) ◽  
pp. 297-308 ◽  
Author(s):  
Morteza Ghaffarpour ◽  
Mohammad Kazemi ◽  
Mohammad Javad Mohammadi Sefat ◽  
Ahmad Aziz ◽  
Kamran Dehghani
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Aluminum Alloys ◽  
Traverse Speed ◽  
Inert Gas ◽  
Dissimilar Joints ◽  
Friction Stir ◽  
Dissimilar Aluminum Alloys ◽  
The Difference ◽  
Welding Processes

In the present study, friction stir welding (FSW) and tungsten inert gas (TIG) techniques were used to join the dissimilar aluminum alloys of 5083-H12 and 6061-T6. The laboratory tests were designed using design of experiment (DOE) method. Variables for the FSW process were the rotational speed, traverse speed, shoulder diameter, and pin diameter. They changed in ranges of 700–2500 r/min, 25–400 mm/min, 10–14 mm, and 2–4 mm, respectively. In the case of TIG process, the variables were current intensity, traverse speed, and tilt angle. These parameters varied from 80 to 90 A, 200 to 400 mm/min, and 3° to 12°, respectively. The optimum amounts of parameters were obtained using response surface methodology (RSM). The RSM-based model was developed to predict ultimate tensile strength (UTS) of the welds produced. In FSW, the difference between predicted and measured UTS was about 1.28% and in TIG it was 1.78%. The good agreement between experimental and predicted results indicates the high accuracy of the developed model. Mechanical properties and also the microstructure of the welds were compared after optimizing both welding processes using RSM. The results showed that the welds produced by FSW indicated a considerably higher quality and also improved mechanical properties compared to TIG. Properties of the joints obtained by FSW in single-sided joints were more desirable. In the double-sided welds obtained by FSW these differences were of an even higher significance.

Sign in / Sign up

Export Citation Format

Share Document