A Simple Hydrothermal Synthesis of Cadmium Sulfide Wrapped on Graphene Nanocomposite for Supercapacitor Applications

2021 ◽  
Vol 21 (12) ◽  
pp. 5835-5845
Author(s):  
Ranjith Balu ◽  
Arivuoli Dakshanamoorthy
Keyword(s):  
Hydrothermal Synthesis ◽  
Specific Surface ◽  
Cadmium Sulfide ◽  
Specific Capacitance ◽  
Surface Area ◽  
Specific Surface Area ◽  
High Current Density ◽  
Specific Capacity ◽  
Cds Nanoparticles ◽  
Electrochemical Characteristics

Supercapacitor with high specific capacity is desirable for various energy storage and high powerdensity applications. Though Graphene has been the preferred material for high current density, nanocomposites have been attempted to increase the specific capacitance. Hydrothermal synthesis of cadmium sulfide/graphene (CdS/G) nanocomposite with CdS nanoparticles anchored/decorated over the graphene sheets is reported. The structural studies reveal the hexagonal phase of the prepared materials. The specific surface area (BET) and porosity is found to increase upon nanocomposite formation. The electrochemical characteristics such as cyclic voltammetry (CV), GCD and EIS of the CdS/G nanocomposite have been investigated. The capacitance of CdS/G nanocomposite almost doubled to 248 Fg−1 indicating the enhanced performance of the nanocomposite system and in addition it also showed excellent cycling stability of 74.8 percent after 1000 cycles. The supercapacitor investigated retained the initial energy density after charge-discharge, at 0.5 A/g for 1000 cycles. The graphene nanosheets increased the specific surface area and interfacial electron transfer of the composite material. It enhances the specific capacitance and cyclic stability of the supercapacitor device.

Design of ZnMoO4 porous nanosheet with oxygen vacancy as better performance electrode material for supercapacitor

2021 ◽  
Author(s):  
Pengxi Li ◽  
Jiepeng Wang ◽  
Liming Li ◽  
Shili Song ◽  
Xianming Yuan ◽  
...  
Keyword(s):  
Hydrothermal Synthesis ◽  
Oxygen Vacancy ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Electrode Material ◽  
Reduction Method

ZnMoO4 with oxygen vacancy (ZnMoO4-OV) porous nanosheet was synthesized by hydrothermal synthesis and hydrogenation reduction method. The ZnMoO4-OV porous nan sheet delivers a higher specific surface area together with a...

Preparation of Fe/N co-doped hierarchical porous carbon nanosheets derived from chitosan nanofibers for high-performance supercapacitors

2021 ◽  
pp. 1-16
Author(s):  
Yaqi Yang ◽  
Ziqiang Shao ◽  
Feijun Wang
Keyword(s):  
Specific Surface ◽  
Specific Capacitance ◽  
Surface Area ◽  
Double Layer ◽  
Specific Surface Area ◽  
Porous Carbon ◽  
Active Sites ◽  
Transport Pathway ◽  
Carbon Nanosheets ◽  
Hierarchical Porous

Abstract Due to the low specific capacitance and small specific surface area of conventional carbon materials used as electrode materials for double-layer capacitors, the search for more ideal materials and ingenious preparation methods remains a major challenge. In this study, fractional porous carbon nanosheets were prepared by co-doping Fe and N with chitosan as nitrogen source. The advantage of this method is that the carbon nanosheets can have a large number of pore structures and produce a large specific surface area. The presence of Fe catalyzes the graphitization of carbon in the carbon layer during carbonization process, and further increases the specific surface area of the electrode material. This structure provides an efficient ion and electron transport pathway, which enables more active sites to participate in the REDOX reaction, thus significantly enhancing the electrochemical performance of SCs. The specific surface area of CS-800 is up to 1587 m2 g−1. When the current density is 0.5 A g−1, the specific capacitance of CS-800 reaches 308.84 F g−1, and remains 84.61 % of the initial value after 10,000 cycles. The Coulomb efficiency of CS-800 is almost 100 % after a long cycle, which indicates that CS-800 has more ideal double-layer capacitance and pseudo capacitance.

Three-dimensional graphene encapsulated hollow CoSe2-SnSe2 nanoboxes for high performance asymmetric supercapacitors

2022 ◽  
Author(s):  
Kainan Li ◽  
Ke Zheng ◽  
Zhifang Zhang ◽  
Kuan Li ◽  
Ziyao Bian ◽  
...  
Keyword(s):  
Electrochemical Performance ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Active Sites ◽  
Specific Capacity ◽  
Three Dimensional ◽  
Hollow Structure ◽  
Large Specific Surface Area ◽  
Composite Aerogel

Abstract Construction of metal selenides with a large specific surface area and a hollow structure is one of the effective methods to improve the electrochemical performance of supercapacitors. However, the nano-material easily agglomerates due to the lack of support, resulting in the loss of electrochemical performance. Herein, we successfully design a three-dimensional graphene (3DG) encapsulation-protected hollow nanoboxes (CoSe2-SnSe2) composite aerogel (3DG/CoSe2-SnSe2) via a co-precipitation method coupled with self-assembly route, followed by a high temperature selenidation strategy. The obtained aerogel possesses porous 3DG conductive network, large specific surface area and plenty of reactive active sites. It could be used as a flexible and binder-free electrode after a facile mechanical compression process, which provided a high specific capacitance of 460 F g-1 at 0.5 A g-1, good rate capability of 212.7 F g-1 at 10 A g-1, and excellent cycle stability due to the fast electron/ion transfer and electrolyte diffusion. With the as-prepared 3DG/CoSe2-SnSe2 as positive electrodes and the AC (activated carbon) as negative electrodes, an asymmetric supercapacitor (3DG/CoSe2-SnSe2//AC) was fabricated, which delivered a high specific capacity of 38 F g-1 at 1A g-1 and an energy density of 11.89 W h kg-1 at 749.9 W kg-1, as well as a capacitance retention of 91.1% after 3000 cycles. This work provides a new method for preparing electrode material.

Enteromorpha based porous carbons activated by zinc chloride for supercapacitors with high capacity retention

RSC Advances ◽  
2015 ◽  
Vol 5 (21) ◽  
pp. 16575-16581 ◽  
Author(s):  
Mingbo Wu ◽  
Peng Li ◽  
Yang Li ◽  
Jun Liu ◽  
Yang Wang
Keyword(s):  
Specific Surface ◽  
Specific Capacitance ◽  
Surface Area ◽  
Specific Surface Area ◽  
Zinc Chloride ◽  
Porous Carbon ◽  
High Capacity ◽  
Porous Carbons ◽  
Capacity Retention

Porous carbons were prepared from enteromorpha with ZnCl2 as active reagent. The prepared porous carbon with a specific surface area of 1651 m2 g−1 exhibited a specific capacitance of 206 F g−1 and capacity retention of 93% even after 5000 cycles.

Preparation of Nanosize Anatase TiO2 Powders by Hydrothermal Synthesis

2007 ◽  
Vol 336-338 ◽  
pp. 2017-2020 ◽  
Author(s):  
Fan Yong Ran ◽  
Wen Bin Cao ◽  
Yan Hong Li ◽  
Xiao Ning Zhang
Keyword(s):  
Grain Size ◽  
Hydrothermal Synthesis ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Reaction Temperature ◽  
Reaction System ◽  
Anatase Tio2 ◽  
Holding Time ◽  
Precursor Concentration

Nanosize anatase TiO2 powders have been synthesized by hydrothermal synthesis by using technical grade TiOSO4 as precursor and urea as precipitating agent. The initial pressure of the reaction system was set at 6 MPa. Stirring speed was fixed at 300r/min. The reaction system reacted at the temperature ranged from 110 to 150°C for holding 2hrs to 8hrs and the concentration of the precursor was ranged from 0.25M to1.5M. XRD patterns show that the synthesized powders are in the form of anatase phase. Calculated grain size is ranged from 6.7 to 8.9nm by Scherrer method from the line broadening of the (101) diffraction peak of anatase. The specific surface area of the powders synthesized under different conditions is ranged from 124 to 240m2/g. The grain size of the powders increases with the increase of the reaction temperature, holding time and precursor concentration, respectively. The specific surface area decreases with the increase of reaction temperature and holding time, and does not obviously change with the change of precursor concentration when the concentration of the precursor is less than 1M. However, when the concentration is higher than 1M, the specific surface area will decrease quickly with the increase of the precursor concentration. XRD and DSC-TG analysis shows that the synthesized anatase TiO2 will begin to transform to rutile TiO2 at about 840°C. When heated to 1000°C for holding 1h, the anatase powders will transform to rutile completely.

Modified polyacrylonitrile-based activated carbon fibers applied in supercapacitor

2016 ◽  
Vol 45 (3) ◽  
pp. 164-171 ◽  
Author(s):  
Linjie Su ◽  
Bohong Li ◽  
Dongyu Zhao ◽  
Chuanli Qin ◽  
Zheng Jin
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Specific Capacitance ◽  
Surface Area ◽  
Specific Surface Area ◽  
Carbon Fibers ◽  
Electrode Material ◽  
High Specific Capacitance ◽  
Activated Carbon Fibers ◽  
Content Type

Purpose The purpose of this paper is to prepare a new modified activated carbon fibers (ACFs) of high specific capacitance used for electrode material of supercapacitor. Design/methodology/approach In this study, the specific capacitance of ACF was significantly increased by using the phenolic resin microspheres and melamine as modifiers to prepare modified PAN-based activated carbon fibers (MACFs) via electrospinning, pre-oxidation and carbonization. The symmetrical supercapacitor (using MACF as electrode) and hybrid supercapacitor (using MACF and activated carbon as electrodes) were tested in term of electrochemical properties by cyclic voltammetry, AC impedance and cycle stability test. Findings It was found that the specific capacitance value of the modified fibers were increased to 167 Fg-1 by adding modifiers (i.e. 20 wt.% microspheres and 15 wt.% melamine) compared to that of unmodified fibers (86.17 Fg-1). Specific capacitance of modified electrode material had little degradation over 10,000 cycles. This result can be attributed to that the modifiers embedded into the fibers changed the original morphology and enhanced the specific surface area of the fibers. Originality/value The modified ACFs in our study had high specific surface area and significantly high specific capacitance, which can be applied as efficient and environmental absorbent, and advanced electrode material of supercapacitor.

Preparation of Activated Carbons from Lignite for Electrochemical Capacitors by Microwave and Electrical Furnace Heating

2011 ◽  
Vol 194-196 ◽  
pp. 2472-2479 ◽  
Author(s):  
Bao Lin Xing ◽  
Chuan Xiang Zhang ◽  
Lun Jian Chen ◽  
Guang Xu Huang
Keyword(s):  
Specific Surface ◽  
Specific Capacitance ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Activated Carbons ◽  
Electrochemical Capacitors ◽  
Weight Ratio ◽  
Total Pore Volume ◽  
Electrochemical Performances

Activated carbons (ACs) were prepared from lignite by microwave (MW) and electrical furnace (EF) heating with KOH as activation agent. In order to compare pore structures and electrochemical performances of ACs prepared by both heating methods, the ACs were characterized by N2 adsorption at 77K, X-ray diffraction (XRD) and scanning electron microscope (SEM). The electrochemical performances of Electrochemical capacitors (ECs) with ACs as electrodes in 3mol/L KOH electrolyte were evaluated by constant current charge-discharge, cyclic voltammetry and electrochemical impedance spectroscopy. The results show that the pore structures of ACs prepared by MW and EF heating significantly enhance when the weight ratio of KOH to coal increases from 2 to 4. The BET specific surface area, total pore volume, the ratio of mesopore and average pore diameter of ACs prepared by MW heating (denoted as AC-MW4) reaches 2094m2/g, 1.193cm3/g, 53.6%, 2.28nm when the weight ratio of KOH to coal is 4, and ACs prepared by EF heating (denoted as AC-EF4) reaches 2580m2/g, 1.683cm3/g, 67.3%, 2.61nm. The ECs with AC-MW4 and AC-EF4 as electrodes present a high specific capacitance of 348F/g and 377F/g at a current density of 50mA/g, and still remain 325F/g and 350F/g after 500 cycles, respectively. Although the specific surface area, total pore volume and specific capacitance of ACs prepared by MW heating are slightly lower than EF heating, taking into account the heating time in the activation process, ACs prepared by EF heating needs approximate 140min, while MW heating only needs 10min, which have demonstrated that microwave heating technology is a promising and efficient technique to prepare ACs.

The Hydrothermal Synthesis and Photocatalysis of TiO2 Powders

2011 ◽  
Vol 183-185 ◽  
pp. 2024-2027
Author(s):  
Li Ming Jiang
Keyword(s):  
Photocatalytic Activity ◽  
Hydrothermal Synthesis ◽  
Specific Surface ◽  
Surface Area ◽  
Specific Surface Area ◽  
Organic Molecule ◽  
Photocatalytic Performance ◽  
Hydrothermal Conditions ◽  
Anatase Structure

Titania powders were prepared under hydrothermal conditions by employing organic molecule β-cyclodextrin(CD) as template, and characterized by means of TGA、XRD、BET . The effects of the pH on the specific surface area and photocatalytic performance of titania were discussed. The results showed that titania powders were anatase structure;the titania powders with specific surface area up to 216.2 m2g-1 were prepared while the system pH was about 1 , and the powders had the best photocatalytic activity.

Hydrothermal synthesis of Sm-doped Bi2WO6 flower-like microspheres for photocatalytic degradation of rhodamine B

CrystEngComm ◽  
2019 ◽  
Vol 21 (41) ◽  
pp. 6208-6218 ◽  
Author(s):  
Xianghui Zhang ◽  
Mingming Zhang ◽  
Kaixuan Cao
Keyword(s):  
Hydrothermal Synthesis ◽  
Optical Absorption ◽  
Specific Surface ◽  
Photocatalytic Degradation ◽  
Surface Area ◽  
Specific Surface Area ◽  
Rhodamine B

Sm-doped Bi2WO6 with 3D flower-like microspheres structure shows extremely high photodegradation activity and superior stability and reusability because of the optimum optical absorption activity and the larger specific surface area.

scholarly journals N, S-Codoped Activated Carbon Material with Ultra-High Surface Area for High-Performance Supercapacitors

Polymers ◽  
2020 ◽  
Vol 12 (9) ◽  
pp. 1982
Author(s):  
Qinghua Yuan ◽  
Zhuwen Ma ◽  
Junbiao Chen ◽  
Zhenrui Huang ◽  
Zeming Fang ◽  
...  
Keyword(s):  
Activated Carbon ◽  
Specific Surface ◽  
Specific Capacitance ◽  
Surface Area ◽  
Specific Surface Area ◽  
Carbon Material ◽  
High Surface ◽  
Koh Activation ◽  
Supercapacitor Electrode ◽  
Tobacco Stalk

The recycling of macromolecular biowastes has been a problem for the agriculture industry. In this study, a novel N, S-codoped activated carbon material with an ultrahigh specific area was produced for the application of a supercapacitor electrode, using tobacco stalk biowastes as the carbon source, KOH as the activating agents and thiourea as the doping agent. Tobacco stalk is mainly composed of cellulose, but also contains many small molecules and inorganic salts. KOH activation resulted in many mesopores, giving the tobacco stem-activated carbon a large specific surface area and double-layer capacitance. The specific surface area of the samples reached up to 3733 m2·g−1, while the maximum specific capacitance of the samples obtained was up to 281.3 F·g−1 in the 3-electrode tests (1 A·g−1). The doping of N and S elements raised the specific capacitance significantly, which could be increased to a value as high as 422.5 F·g−1 at a current density of 1 A·g−1 in the 3-electrode tests, but N, S-codoping also led to instability. The results of this article prove that tobacco stalks could be efficiently reused in the field of supercapacitors.

Sign in / Sign up

Export Citation Format

Share Document